Mac allister MBC1042 Manual
  1. Manuals
  2. Brands
  3. Mac allister Manuals
  4. Brush Cutter
  5. MBC1042
  6. Manual

Mac allister MBC1042 Manual

2-in-1 brush cutter 1000w 23cm/ 42cm
Hide thumbs

Advertisement

Table of Contents

EN
2-in-1 Brush
Cutter 1000W
23cm/ 42cm
MBC1042
WARNING: Read the instructions before using the product!

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MBC1042 and is the answer not in the manual?

Questions and answers

Related Manuals for Mac allister MBC1042

Summary of Contents for Mac allister MBC1042

  • Page 1 2-in-1 Brush Cutter 1000W 23cm/ 42cm MBC1042 WARNING: Read the instructions before using the product!
  • Page 2 Let’s get started... These instructions are for your safety. Please read through them thoroughly before use and retain them for future reference. started... Getting Safety information Your product Before you start detail... more Product functions Operation Care and maintenance Troubleshooting Recycling and disposal Guarantee Technical specifications...
  • Page 3 MBC1042 by MacAllister Safety information Safety warnings General safety warnings 1. Never allow children, persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge or people unfamiliar with these instructions to use the machine, local regulations may restrict the age of the operator.
  • Page 4 Safety information MBC1042 by MacAllister Safety warnings which may ignite the dust or fumes. 3. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. Electrical safety 1. Power tool plugs must match the outlet. Never modify the plug in any way.
  • Page 5 MBC1042 by MacAllister Safety information influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. 2. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
  • Page 6 Safety information MBC1042 by MacAllister Safety warnings tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. 2. Do not use the power tool if the switch does not turn it on and off.
  • Page 7 MBC1042 by MacAllister Safety information and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations. Service 1. Have your power tools serviced by a qualified repair person using only identical replacement parts.
  • Page 8 Safety information MBC1042 by MacAllister Safety warnings damaged, missing or misplaced guards or shields. 4. Never operate the machine while people, especially children, or pets are nearby. Operation 1. Keep supply and extension cords away from cutting means. 2. Wear eye protection and stout shoes at all times while operating the machine.
  • Page 9 MBC1042 by MacAllister Safety information remove the plug from the mains, remove the disabling device or removable battery) before carrying out maintenance or cleaning work. 2. Use only the manufacturer’s recommended replacement parts and accessories. 3. Inspect and maintain the machine regularly. Have the machine repaired only by an authorized repairer.
  • Page 10 Safety information MBC1042 by MacAllister Safety warnings cord or extension cord may result in electric shock, fire and/or serious injury. 6. Follow instructions for changing accessories. Improperly tightened blade securing nuts or bolts may either damage the blade or result in it becoming detached.
  • Page 11 Safety information MBC1042 by MacAllister only when standing on the ground. Slippery or unstable surfaces may cause a loss of balance or control of the machine. 15. Do not operate the machine on excessively steep slopes. This reduces the risk of loss of control, slipping and falling which may result in personal injury.
  • Page 12 Safety information MBC1042 by MacAllister Safety warnings parts while they are still in motion. This reduces the risk of injury from moving parts. 23. When clearing jammed material or servicing the machine, make sure all power switches are off and the power cord is disconnected.
  • Page 13 Safety information MBC1042 by MacAllister Blade thrust can increase the risk of injury due to the machine moving unexpectedly. Blade thrust can be controlled by the operator if proper precautions are taken. 2. If the blade binds, or when interrupting a cut for any...
  • Page 14 Safety information MBC1042 by MacAllister 3. Use correct attachments for the product and ensure they are in good condition. 4. Keep tight grip on the handles/grip surface. 5. Maintain this product in accordance with these instructions and keep it well lubricated (where appropriate).
  • Page 15 Safety information MBC1042 by MacAllister 1. Health defects resulting from vibration emission if the product is being used over long periods of time or not adequately managed and properly maintained. 2. Injuries and damage to property due to broken attachments or the sudden impact of hidden objects during use.
  • Page 16 Safety information MBC1042 by MacAllister Symbols On the product, the rating label and within these instructions you will find among others the following symbols and abbreviations. Familiarise yourself with them to reduce hazards like personal injuries and damage to property. Volt, (alternating voltage) Hertz /min or Per minute Watt Gram Kilogram Millimetre Metre Centimeter m/s²...
  • Page 17 Safety information MBC1042 by MacAllister Objects thrown by the product could hit the user or other bystanders. Always ensure that other people and pets remain at a safe distance from the product when it is in operation. In general, children must not come near the area where the product is.
  • Page 18 Your product MBC1042 by MacAllister Your product 23 22 21...
  • Page 19 Your product MBC1042 by MacAllister Your product 1. On/Off switch b. Locking sleeve e. Release latch (x2)* 2. Lock-off button c. Bore f. Eyelet (x2)* 3. Right-handle bar d. Bolt g. Spring* 4. Left-handle bar 16. Lower pole h. Housing* 5.
  • Page 20 Before you start MBC1042 by MacAllister You will need (items not supplied) (items supplied) Suitable personal protective equipment Guard (17) Suitable crosshead screwdriver Trimmer head (18) Cutter blade (3-Teeth) (19) Harness (20) Multi tool (21) Spindle lock rod (22) Hex key (23) NOTE: The accessories required depend on the intended application.
  • Page 21 MBC1042 by MacAllister Before you start Fig. 1 Fig. 2 WARNING! Make sure bolt (15d) and lock knob (15) are properly tightened before using the product. Guard 1. Remove the bolt (17a) from the guard (17) by using the supplied multi tool (21) and keep it handy (Fig.
  • Page 22 Before you start MBC1042 by MacAllister Setup WARNING! Never use the trimmer head (18) or cutter blade (19) without the guard (17) properly fitted. NOTE: Always remove knife protector (17e) before use. Handle bars Adjust the handle bars (3, 4) to the suitable position to fit the intended use (Fig. 4, 5): Fig. 4 (Storage position) Fig. 5 (Working position) 1.
  • Page 23 MBC1042 by MacAllister Before you start Fig. 6 5. Attach the electric cord (10) with the cord clip (smaller) (14) on the righthandle bar (3), the cord clip (bigger) (12) on the upper pole (11) (Fig. 7). Fig. 7 WARNING! Never use the product without the handle bars (3, 4)
  • Page 24 Before you start MBC1042 by MacAllister Setup 6. Remove the spindle lock rod (22) (Fig. 8). Fig. 8 Cutter blade 1. Rotate the backing flange (19d) until its hole is aligned with the notch in the gear head. 2. Insert the spindle lock rod (22) into the hole to lock the spindle (19e). 3. Loosen the trimmer head (18) clockwise by hand and remove it together with the locking flange (19c).
  • Page 25 MBC1042 by MacAllister Before you start Connection to power supply NOTE: The product is equipped with a power cord with the length of 12 m. If a proper extension cord is required for operation. Observe the technical requirements for this product when purchasing an extension cord.

  • Page 26: Table Of Contents

    MBC1042 by MacAllister more detail... Product functions Operation Care and maintenance Troubleshooting Recycling and disposal Guarantee Technical specifications Declaration of conformity...
  • Page 27 MBC1042 by MacAllister Product functions Intended use This electric 2-in-1 brush cutter MBC1042 is designated with a rated power input of 1000 Watts. With the trimmer head attached the product is intended to cut smaller types of weed, lawn grass or similar soft vegetation.
  • Page 28 MBC1042 by MacAllister Product functions Harness 3. Adjust the length of the harness (20) so that the securing clip (20a) is approximately 15 cm below your waist. 4. Attach the securing clip (20a) to the loop the suspension sleeve (11a) (Fig. 14).
  • Page 29 MBC1042 by MacAllister Product functions Fig. 17 Cutting attachments Trimmer head Use the trimmer head (18) to cut smaller types of weed, lawn grass or similar soft vegetation. Cutter blade Use the cutter blade (19) to cut heavier weeds, brush and similar vegetation.

  • Page 30: Product Functions

    MBC1042 by MacAllister Product functions / Operation Switching on/off 1. Hold the product with one hand at the lefthandle bar (4) and with the other at the righthandle bar (3). 2. Press the lock-off button (2) and hold it in position (Fig.
  • Page 31 MBC1042 by MacAllister Operation Cutting 1. Attach the cutter blade (19) to cut heavier weeds, brush and similar vegetation. Make sure that the guard (17) has been attached properly. WARNING! To avoid hazards never cut heavier weeds, brush and similar vegetation with a thickness exceeding the capacity stated in section ”Technical specification”!
  • Page 32 Operation MBC1042 by MacAllister Trimming 1. Attach the trimmer head (18) to cut to cut smaller types of weed, lawn grass or similar soft vegetation. Make sure that the guard (17) has been attached properly. 2. Hold the product firmly with a gap between the product and your right side. 3. Stand upright, do not lean forward and pay attention to posture. Keep both feet apart to help retain your balance.
  • Page 33 MBC1042 by MacAllister Operation Tips 1. For best results, do not cut wet grass because it tends to stick to the cutting head and guard, prevents proper discharge of grass trimmings, and could cause you to slip and fall. 2. Do not allow the spool cover to drag on the ground or other surfaces.
  • Page 34 Operation MBC1042 by MacAllister Trimming Line feeding 1. Tap the bumper (18b) on solid ground and the trimmer head (18) will release trimming line (18d). 2. Excess line will be cut by the knife (17d) (Fig. 26). Fig. 26 WARNING! The trimming line (18d) will be thrown out! Danger of injury...
  • Page 35 MBC1042 by MacAllister Care and maintenance The golden rules for care WARNING! Always switch the product off, disconnect the product from the power supply and let the product cool down before performing inspection, maintenance and cleaning work! 1. Keep the product clean. Remove debris from it after each use and before storage.
  • Page 36 Care and maintenance MBC1042 by MacAllister Cutting attachments Replace worn or damaged cutting attachments. WARNING! Never use other blades including metal multi-piece pivoting chains and flail blades. Otherwise serious injury may result. 1. Keep the cutting attachments and the safety guard clean and free of debris. Remove grass trimmings.
  • Page 37 MBC1042 by MacAllister Care and maintenance 6. Remove the cover (18a) and the trimming spool (18c) from the housing (18h) (Fig. 28, step 3). Fig. 27 Fig. 28 7. Clean the housing (18h) before inserting a new trimming spool (18c) of the same type.
  • Page 38 Care and maintenance MBC1042 by MacAllister Trimming line Refill the trimming line in the trimming spool 1. Remove the trimming spool (18c) from the housing (18h) as instructed in chapter “Trimming line - Replace the trimming spool”. 2. Discard all the remaining line (18d) from the trimming spool (18c).
  • Page 39 MBC1042 by MacAllister Care and maintenance UK plug (only for UK market) If you need to replace the fitted plug, then follow the instructions below. IMPORTANT: The wires in the mains lead are coloured in accordance with the following code: Blue – Neutral Brown – Live As the colours of the wire in the mains lead of this product may not correspond with the coloured marking identifying the terminals in your plug, proceed as follows.

  • Page 40: Troubleshooting

    Care and maintenance / Troubleshooting MBC1042 by MacAllister Storage 1. Switch the product off and disconnect it from the power supply. 2. Clean the product as described above. 3. Disassemble two handle bars (3, 4) to storage position, if necessary.

  • Page 41: Recycling And Disposal

    Troubleshooting / Recycling and disposal MBC1042 by MacAllister Problem Possible cause Solution 1. Product does not 1.1. Not connected to power 1.1. Connect to power supply start supply 1.2. Power cord or plug is 1.2. Check by a specialist defective electrician 1.3.

  • Page 42: Guarantee

    Guarantee MBC1042 by MacAllister Guarantee We take special care to select high quality materials and use manufacturing techniques that allow us to create products incorporating design and durability. This product has a manufacturer’s guarantee of 2 years against manufacturing defects, from the date of purchase (if bought in store) or date of delivery (if bought online), at no additional cost for normal (non-professional or commercial) household use.
  • Page 43 MBC1042 by MacAllister Guarantee Distributor: B&Q plc Chandlers Ford, Hants, SO53 3LE, United Kingdom www.diy.com Screwfix Direct Limited Trade House, Mead Avenue, Yeovil, BA22 8RT, United Kingdom www.screwfix.com...

  • Page 44: Technical Specifications

    MBC1042 by MacAllister Technical specifications Technical specifications General >Rated voltage, frequency : 230-240 V~,50 Hz >Rated power input : 1000 W >Rated no load speed n : 6200 min (as grass trimmer) 7100 min (as brush cutter) >Protection class : II / >Weight...
  • Page 45 Proper measures include among others regular maintenance and care of the product and accessories, keeping hands warm, periodical breaks and proper planning of work processes. Rating label explanation 2-in-1 Brush Cutter: MBC1042 M = MAC Allister 10 = Rated power (1000W) BC = 2-in-1 Brush Cutter...

  • Page 46: Declaration Of Conformity

    Declaration of conformity MBC1042 by MacAllister Declaration of conformity...

Table of Contents

Save PDF