Horizon Fitness ADVENTURE 3, ADVENTURE 5 - Treadmill Manual

Horizon Fitness ADVENTURE 3, ADVENTURE 5 - Treadmill Manual

Advertisement

Horizon Fitness ADVENTURE 3, ADVENTURE 5 - Treadmill Manual

ASSEMBLY


There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the treadmill could have parts that are not tightened and will seem loose and may cause irritating noises. To prevent damage to the treadmill, the assembly instructions must be reviewed and corrective actions should be taken.

Before proceeding, find your treadmill's serial number located on a white barcode sticker near the on/off power switch and power cord and write it down for future reference.
MODEL NAME LABEL

SERIAL NUMBER LOCATION

» Refer to the SERIAL NUMBER and MODEL NAME when calling for service.

PRODUCT PARTS

TOOLS REQUIRED

  • T-Wrench (included)
  • L-Wrench (included)
  • Screwdriver (not included)

PARTS INCLUDED

  • 2 Console Masts
  • 1 Console Assembly
  • 1 Hardware Kit
  • 1 Safety Key
  • 1 Power Cord
  • 1 Audio Adapter Cable
  • 1 Bottle of Silicone Lubricant (for 2 applications)

NEED HELP?
If you have questions or if there are any missing parts, contact Customer Tech Support. Contact information is located on the back cover of this manual.

UNPACKING

Place the treadmill carton on a level flat surface. It is recommended that you place a protective covering on your floor. Take CAUTION when handling and transporting this unit. Never open box when it is on its side. Once the banding straps have been removed, do not lift or transport this unit unless it is fully assembled and in the upright folded position, with the lock latch secure. Unpack and assemble the unit where it will be used. The enclosed treadmill is equipped with high-pressure shocks and may spring open if mishandled. Never grab hold of any portion of the incline frame and attempt to lift or move the treadmill.

  • DO NOT ATTEMPT TO LIFT THE TREADMILL! Do not move or lift treadmill from packaging until specified to do so in the assembly instructions. You may remove the plastic wrap from console masts.
  • FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN INJURY!

  • During each assembly step, ensure that ALL nuts and bolts are in place and partially threaded. It is recommended you complete the full assembly of your unit before completely tightening any ONE bolt.
  • Several parts have been pre-lubricated to aid in assembly and usage. Please do not wipe this off. If you have difficulty, a light application of lithium bike grease is recommended.

STEP 1

HARDWARE FOR STEP 1
PART TYPE QTY
A BOLT 3

ASSEMBLY - STEP 1

  1. Cut the yellow banding straps and lift the running deck upward to remove all contents from underneath the running deck.
  2. Open HARDWARE FOR STEP 1.
  3. Attach LEFT CONSOLE MAST (1) to MAIN FRAME (2) using 3 BOLTS (A).

STEP 2

HARDWARE FOR STEP 2
PART TYPE QTY
A BOLT 3

ASSEMBLY - STEP 2

  1. Pull the BASE CABLE (3) away from the treadmill base frame. Connect the CONSOLE CABLE (3) from the MAIN FRAME (2) to the CONSOLE CABLE (3) in the bottom of the RIGHT CONSOLE MAST (4). The other end of the CONSOLE CABLE should be located at the top of the mast.
  2. Open HARDWARE FOR STEP 2.
  3. Attach RIGHT CONSOLE MAST (4) to MAIN FRAME (2) using 3 BOLTS (A).

NOTE: Be careful not to pinch the console cable while attaching the right console mast.

STEP 3

HARDWARE FOR STEP 3
PART TYPE QTY
B BOLT 6
C ARC WASHER 6
D SPRING WASHER 6

ASSEMBLY - STEP 3 - INSTALLING THE HANDLEBARS

  1. Open HARDWARE FOR STEP 3.
  2. Slide HANDLEBARS (5) onto CONSOLE (6).
  3. Attach HANDLEBARS (5) to CONSOLE (6) using 3 BOLTS (B), 3 SPRING WASHERS (C) and 3 ARC WASHERS (D) from each side.

STEP 4

HARDWARE FOR STEP 4
PART TYPE QTY
E BOLT 6
F SPRING WASHER 6
G FLAT WASHER 4
H ARC WASHER 2

ASSEMBLY - STEP 4 - INSTALLING THE CONSOLE

  1. Open HARDWARE FOR STEP 4.
  2. Gently place CONSOLE (5) on top of CONSOLE MASTS (1 & 4).
    NOTE: Be careful not to pinch the console cables while attaching the console.
  3. Connect the CONSOLE CABLES (7) and ensure they are tucked inside the CONSOLE (6).
  4. Connect the CONSOLE (6) to the right CONSOLE MAST (4) using 2 BOLTS (E), 2 SPRING WASHERS (F) and 2 FLAT WASHERS (G) from the inside of the mast and 1 BOLT (E), 1 SPRING WASHER (F) and 1 ARC WASHER (H) from the front of the mast.
  5. Repeat STEP D on left side.

ASSEMBLY COMPLETE
Before the first use, lubricate the treadmill deck by following the instructions in the MAINTENANCE section in the TREADMILL GUIDE.

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Horizon Fitness ADVENTURE 3, ADVENTURE 5 - Treadmill Manual

Advertisement

Need help?

Need help?

Do you have a question about the ADVENTURE 3 and is the answer not in the manual?

Questions and answers

Table of Contents