Operation; Maintenance; Optional Accessories - Makita UT2204 Instruction Manual

ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and unplugged before carrying out
any work on the tool.
Installing the shaft
1. Tighten the shaft into the shaft holder till the hex
nut contacts with the shaft holder.
► Fig.4: 1. Hex nut 2. Shaft 3. Shaft holder
2. Hold the notch in the shaft holder with wrench 19 so
that it cannot revolve. With the notch held so, tighten the
hex nut with another wrench 19 in the direction of arrow.
► Fig.5: 1. Wrench 19 2. Notch 3. Wrench 19
Installing the mixing blade
► Fig.6: 1. Mixing blade
► Fig.7: 1. Hex bolt 2. Shaft 3. Flat surface
Insert the mixing blade into the shaft and secure it with the hex bolt.
At this time, position it so that the top end of the hex bolt
always fits to the flat surface on the shaft and tighten
the hex bolt with the provided wrench.
When installing the mixing blades at two different positions
(which is applicable only to the mixing blades allowed to
do so), mount and secure the two mixing blades on the flat
part of the shaft with the hex bolts so that the same sur-
face of blades faces each other as shown in the figure.
► Fig.8: 1. Mixing blade 2. Shaft
► Fig.9: 1. Hex bolt 2. Shaft 3. Flat surface

OPERATION

CAUTION:
Do not mix flammable materials or oper-
ate the tool around flammable materials such as paint with
thinner used as solvent. Failure to do so may cause an injury.
1. Hold the rear handle of the tool with one hand and the grip
with the other hand firmly, place the mixing blade under material
fully and turn on the tool after making sure work site safety.
2. Move the mixing blade up and down during the mix-
ing operation so that whole part of material can be mixed.
3.
When finishing mixing, turn off the tool, make sure
that the mixing blade has come to a complete stop, and
then pull it out of the mixing container.

MAINTENANCE

CAUTION:
Always be sure that the tool is
switched off and unplugged before attempting to
perform inspection or maintenance.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
Replacing filter
► Fig.10: 1. Filter 2. Cover 3. Screwdriver
Replace the filter regularly as the cooling efficiency of
the tool is reduced due to built-up dust or particles in
the filter.
Insert the slotted bit screwdriver and the like between
the tool and the cover as shown in the figure. Lift it up
just like using a shovel and remove the cover.
Replace the filter in the cover with a new one.
Reinstall the cover on the tool.
Replacing carbon brushes
► Fig.11: 1. Limit mark
Check the carbon brushes regularly.
Replace them when they wear down to the limit mark.
Keep the carbon brushes clean and free to slip in the
holders. Both carbon brushes should be replaced at the
same time. Use only identical carbon brushes.
1. Use a screwdriver to remove the brush holder
caps.
2. Take out the worn carbon brushes, insert the new
ones and secure the brush holder caps.
► Fig.12: 1. Brush holder cap
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
OPTIONAL
ACCESSORIES
CAUTION:
These accessories or attachments
are recommended for use with your Makita tool
specified in this manual. The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or attachment
for its stated purpose.
If you need any assistance for more details regard-
ing these accessories, ask your local Makita Service
Center.
• Mixing blade
Type
Mixing blade 175
Mixing blade 190
Mixing blade 220
Mixing blade 135
Mixing blade 183
Mixing blade 201
• Shaft
NOTE: Some items in the list may be included in the
tool package as standard accessories. They may
differ from country to country.
6 ENGLISH
Maximum diameter Twin blade
possible
175 mm Possible
190 mm Possible
220 mm
135 mm
183 mm Possible
201 mm Possible
-
-