GE 89586LO Instructions

20 LED DUAL COLOR G-50 ICE LIGHTS
NHL Model No. 89586LO
IMPORTANT SAFETY INSTRUCTIONS
When using electric products, basic precautions should always be followed including the following:
READ & FOLLOW ALL SAFETY INSTRUCTIONS
1. This is an electric product-not a toy! To avoid risk of fire, burns, personal injury and electric shock, it should not be
played with or placed where small children can reach it.
2. Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When products are used
in outdoor applications, connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet. If one is not
provided, contact a qualified electrician for proper installation.
3. Do not use this product for other than its intended use.
4. This seasonal use product is not intended for permanent use or installation.
5. Unplug when leaving the house, when retiring for the night, or if left unattended.
6. Do not mount or place near gas or electric heaters, fireplaces, candles or other similar sources of heat.
7. Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
8. Do not hang ornaments or other objects from cord, wire, or light string.
9. Do not place lighting string on carpeting, drapes, furniture, or allow it to contact vinyl siding while the power is on.
10. Do not perform any maintenance or troubleshoot for bad or broken lamps while the power is on.
11. Do not close doors or windows on the product or extension cords as this may damage the wire insulation.
12. Do not cover the product with cloth, paper or any material not part of the product when in use.
13. This product is equipped with non- shunted type LED lamps. Do not twist or attempt to remove lamps.
14. Do not let lamps rest on the supply cord or on any wire.
15. Read and follow all instructions that are on the product or provided with the product.
SAVE THESE INSTRUCTIONS
USE AND CARE INSTRUCTIONS
1. Before using or reusing, inspect product carefully. Discard any products that have cut, damaged, or frayed
wire insulation or cords, cracks in the lamp holders or enclosures, loose connections, or exposed copper wire.
2. Before storing the product, carefully remove the product from wherever it is placed, including trees,
branches, or bushes, to avoid any undue strain or stress on the product conductors, connections, and wires.
3. When not in use, store neatly in a cool, dry location protected from sunlight.
4. When the product is used on a live tree, the tree should be well maintained and fresh. Do not place on live
trees in which the needles are brown or break off easily. Keep the tree holder filled with water.
5. lf the product is placed on a tree, the tree should be well secured and stable.
USER SERVICING INSTRUCTIONS:
WARNING:
1. Do not use where only part of the power unit is protected from rain
or water (outlet boxes where there is only a partial cover shall not be used for outdoor installations).
2. This power unit is intended to be correctly oriented in a vertical or floor mount position.
3. If the connector of this lighting string does not properly fit into the connector of the driver,
do not modify the product and discard product if the connector is damaged.
-SEE OTHER SIDE-
-CONTINUED FROM OTHER SIDE-
NOTE:
Use only this GE branded, SEASONAL-USE LED DRIVER Power Supply,
Model TS-8W29V, manufactured by Guang Zhou Ting Shen Electric Co Ltd.
that was provided with this product.
DO NOT use this adapter with any other product.
To replace lamp:
1.Grasp plug and remove from the receptacle or other outlet device.
Do not unplug by pulling on cord.
2.Pull lamp and plastic base straight out of lampholder.
3.Replace lamp with only 3.3 Volt, 0.066 Watt, LED type lamp(provided with product).
CAUTION:
1. This lighting string is rated 19.2 Watts (0.16Amps), do not overload.
GE microbright light set come pre-attached to a plug. For end-to-end connections up to three (3) sets, you will need only
one (1) plug. To begin, choose one (1) set as your master set. This set would be the only set connected to a plug. Next,
unscrew the coaxial connector between the light set on all of the sets you would connect to your master set. Lastly,
connect each set of lights end-to-end using the coaxial connections, screwing each connection cap tightly.
Note: you may only add two (2) additional sets to your master set for a total of three (3) connected sets.
2. To reduce the risk of fire electric shock: a) Do not install on trees having needles, leaves or branch
coverings of metal or materials that look like metal, and b)Do not mount or support strings in a manner
that can cut or damage wire insulation.
3. To reduce the risk of overheating, a) replace burned out lamps promptly. Use 3.3 Volt, 0.066Watt LED lamps provided
with this product .b) Risk of fire .This product does not contain lamp shunts in order to allow the product to operate if
one lamp burns out. Do not replace lamps with other than the spare lamps provided with this product.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
⑴ this device may not cause harmful interference, and
⑵ this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could
void the user' s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
For questions and/or assistance, call customer service at 1-877-398-7337 or visit us on the web at www.GEholidaylighting.com
FOR INDOOR AND OUTDOOR USE
PRINTED IN CHINA
Nicolas Holiday Ltd., 246 Spring Hill Road, Unit B, Trumbull CT 06611
©2023 Nicolas Holiday Ltd., Suite 2706 Skyline Tower,39 Wang Kwong Road,Kowloon Bay,Kowloon,Hong Kong
All rights reserved.
②
①
FIG.1 FIG.2
MADE IN CHINA
HC-23