Advertisement
In case of difficulty
If difficulty is experienced after making the initial set up, the table below might help to eliminate the problem. If the trouble cannot
be corrected, check with your dealer.
Symptom
Cause
Correction
No sound from both left a
channels or one channel.
nd right
1. Turntable
output
cable
or
cables disconnected.
2. The
function
switch
of the
amplifier is not set to PHONO.
Loud hum, no music.
1. Check connections to amplifier.
2.Set
the
function
switch
to
PHONO.
Poor connection of turntable out-
put cables.
Loud hum with music.
Make solid connections to ampli-
fier.
1. Turntable output cable picking
up hum from AC cord.
2. The ground wire of the turn- '
table is not connected to GND
terminal of the amplifier.
1. Separate
output cables from
AC cord or reverse AC cord
plug.
. Connect
the ground
wire to
the GND terminal of the ampli-
fier.
Buzzing noise with music.
Turntable
output
cable
picking
up TV signal.
Relocate
output
cord
for mini-
mum pickup.
Howling drowns out mus
volume is increased.
ic when
Speaker vibration is picked up by
turntable.
Separate turntable from speakers.
Turntable platter does not turn.
Poor AC plug contact.
Check connection. Make sure AC
outlet is active.
Poor tracking.
Excessive
dust
on
record
or
stylus.
Remove
dust
from.
stylus
or
record.
Synchro recording is not possible
Specifications
Motor and turntable
Drive system.........cccseceeeeees
1. The synchro cord is not con-
nected.
2. The
cassette
is not
loaded
correctly.
3. The record lock-out tab on the
cassette has been removed.
4. The cssette deck is in play-
back mode.
Output balance ...
Direct-drive system
.Connect
the
synchro
cord
securely
. Load
the cassette
tape cor-
rectly.
. Use a new cassette or place a
piece of adhesive
tape over
the opening
from which
the
tab has.been removed.
. Set the cassette deck in stop
mode.
ptbssateacssnads 2.0 dB
(1,000 Hz, 5 cm/sec.)
Motor.......ccccccsesssceeseseseees Coreless. & slotless FG servo
Load Impedance...............+.. 47 k ohms
motor
Stylus........-.sccseeseeeeeneeeeeeee 0.6 mil diamond
Turntable platter............+.. 29.8 cm (11-3/4") diameter
Optimum Tracking Force.......1.25 grams
0.63
kg (1 4
ib) weight
Compliance............. LTT
TTT TT 7x
10°6 cm/dyne
Speeds......scscecscessesseeseeeeees 2 speeds, 33-1/3 and 45
Replacement Styius............. N-63
aa
Miscellaneous
Wow & flutter.........sreeeeeees 0.025% (WRMS)
Power Requirements............ AC 120 V, 60 Hz: U.S.A.
DIN: 0.05%
and Canada
S/N (Rumble) ...............000000 DIN: 40 dB (unweighted)
AC 240 V, 50 Hz: U.K. and
DIN: 75 dB (weighted)
Auetcsla..
Tonearm
AC 220 V, 50 Hz: Europe
TYPO sieeve
dshvs said deseueeeeess Static-balance finear tracking
NG 120: Wi220-240N,,
Tracking error.............c00ce0es
Cartridge
Furnished cartridge..............
Frequency response.............
Power Consumption............ 10 watts
Dimensions. ..............0seeeeees W
420 mm (16-9/16")
V-63 (T4P VM cartridge)
20 ~ 20,000 Hz
Channel separation.............. Better than 22 dB
Weight..................
(1,000 Hz)
Output voltage..............:0..58 2.3mV.
(1,000 Hz, 5 cm/sec.)
Note:
H
90 mm (3-9/16")
D
359 mm (14-1/8")
eltackss 5.7 kg (12.5 Ib)
We follow a policy of continuous advancements in development. For this reason specifications may be changed without notice.
Advertisement
