Advertisement
2.
INTRODUCTION
Heavy-duty axle stands to safely support vehicles for extended periods of
time. Large saddles for good load distribution. The heavy gauge steel frame
and welded construction gives superior strength and safety. All stands feature
captive, multi-position pin load support. Sold in pairs. Available in five colours.
3.
SPECIFICATION
Model No:
AS6.V2, AS6G, AS6Y, AS6R, AS6O
Capacity Each
6 Tonne (6,000 kg)
Capacity Pair:
12 Tonne (12,000 kg)
Maximum Working Height:
570mm
Minimum Working Height:
370mm
4.
OPERATION
4.1.
Familiarise yourself with the product. Check that the stands are in good condition
and that no damaged has been sustained during transit. Insert the centre column (fig.1.1) in the centre tube (fig.1.2), adjust to height
required and insert the locking pin (fig.1.3).
4.2.
Ensure the maximum load does not exceed 12 tonne per pair of axle stands, (6 tonne for each stand).
4.3.
Refer to vehicle manufactures instructions for recommended support points.
Check that the points are in good condition.
4.4.
Ensure the vehicle brake is on (or in park mode) and wheels are chocked.
4.5.
Adjust height of stand to correspond with the raised vehicle.
4.6.
Check that the locking pin is correctly pushed all the way through the stand collar, centre column and out of the other side, insert safety
pin, then position stands under vehicle at points specified by vehicle manufacturer.
4.7.
Carefully and slowly lower the load onto stands. Ensure the load bearing points sit in the center of the stand saddle and check that the
stands are stable and not leaning. Also ensure that there are no objects or persons that could impede the safe lowering of the vehicle onto
the stands.
4.8.
To remove stands jack vehicle slightly so that stand can be removed.
4.9.
After use, hold the centre column (fig.1.1) firmly when removing the locking pin (fig.1.3). Failure to do so will allow the center column to
fall freely through the main center tube which could be dangerous.
WARNING! Ensure you follow all instructions carefully. Failure to note these warnings may cause damage, serious injury or loss of life.
‰
5.
MAINTENANCE
5.1.
Before each use check to ensure stands and stand welds are not cracked, and that there are no missing and/or damaged parts.
WARNING! Any stand that appears to be damaged in any way must be removed from service immediately.
‰
5.2.
Ensure the locking pins, are in good order and condition.
5.3.
Due to the potential hazards associated with these stands, DO NOT misuse, or make any modification to the stands or components.
5.4.
It is the responsibility of the stands owner to ensure the operator has read these instructions, and that the operator is familiar with the
stands use and limitations.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be
sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When
the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved
containers and dispose of the product and fluids according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call
our technical team on technical@sealey.co.uk or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 3 years from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
© Jack Sealey Limited
sales@sealey.co.uk
Original Language Version
fig.1
www.sealey.co.uk
AS6.V2, AS6G, AS6Y, AS6R, AS6O
REGISTER YOUR
PURCHASE HERE
Issue 6 (3)
04/12/23
Advertisement
