Description (Fig. A); Assembly And Adjustments - DeWalt DCW600N Original Instructions Manual

English
Date Code Position (Fig. C)
The date code 22 , which also includes the year of manufacture,
is printed into the housing.
Example:
2019 XX XX
Year of Manufacture

Description (Fig. A)


WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
1 Battery pack
Battery release button
2
On/Off switch
3
4 Variable speed dial
Depth adjustment ring
5
Motor
6
7 Spindle lock button
Spindle
8
Guide pin groove
9
10 Worklights
Micro-adjustment scale
11
Intended Use
This tool is designed for professional medium-duty routing of
wood, wood products and plastics with 6–8 mm shank bits.
DO nOT use under wet conditions or in the presence of
flammable liquids or gases.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
• Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.

ASSEMBLY AND ADJUSTMENTS


WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.

WARNING: Use only D
E
12
12 Locking lever
D-shaped subbase
13
Turret stop
14
15 Depth adjustment rod
Plunge lock lever
16
Guide pins
17
18 Plunge base side handles
Motor stop
19
Plunge subbase
20
21 Round subbase
WALT battery packs and chargers.
Inserting and Removing the Battery Pack
from the Tool (Fig. B)
nOTE: Make sure your battery pack
To Install the Battery Pack into the Tool Handle
1. Align the battery pack 1 with the rails inside the tool's
handle (Fig. B).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap into place.
To Remove the Battery Pack from the Tool
1. Press the release button 2
out of the tool handle.
2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs (Fig. B)
Some D WALT battery packs include a fuel gauge which
e
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge
button 46 . A combination of the three green LED lights will
illuminate designating the level of charge left. When the level
of charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
Bit Installation and Removal (Fig. D)
To Install the Bit
1. Remove the motor unit from the base unit. Refer to
Removing the Motor from the Fixed Base or Removing
the Motor from the Plunge Base (if needed).
2. Clean and insert the round shank of the desired router bit
into the loosened collet as far as it will go and then pull it
out about 1.6 mm.
3. Depress the spindle lock button
in place while turning the collet nut
wrench provided.
nOTE: The unit is equipped with multiple spindle lock
detents allowing an optional "manual ratchet" method of
tightening the bit.
To tighten with the "manual ratchet" method:
a. Without removing the wrench from the collet nut
release pressure on the spindle lock button
b. With the wrench still on the collet nut, reverse the
tightening direction to reset the wrench position.
c. Depress the spindle lock button again and turn the
wrench clockwise.
d. Repeat the procedure until the collet nut reaches
desired tightness.
NOTICE: Avoid possible damage to the collet. Never
tighten the collet without a bit.
1 is fully charged.
and firmly pull the battery pack
7 to hold the spindle shaft
23 clockwise with the
23 ,
7 .