Sealey SWC420 Instructions Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear a Face
instructions Shield
No Reaching In Keep
Bystanders
away.
1. SAFETY
WARNING! Ensure any Health & Safety, Government, or local authority regulations are adhered to when using this equipment.
‰
IMPORTANT. Read Carefully Before Use. Keep For Future Reference.
9
Familiarise yourself with the application, limitations, and the potential hazards of the chipper.
9
Maintain the chipper in good condition (use an authorised service agent). Replace or repair damaged parts. Use genuine parts only.
9
Unauthorised parts may be dangerous and will invalidate the warranty.
This chipper is designed and manufactured for specific applications. DO NOT attempt to modify the unit or use it for any application for
9
which it is not designed. If you have any questions regarding the application of the unit please contact your local Sealey stockist.
WARNING! Chipper exhaust gases contain deadly carbon monoxide which must not be inhaled. Always allow sufficient ventilation.
‰
WARNING! Petrol is highly flammable and petrol vapour is explosive. DO NOT permit smoking, naked flames, sparks or heat in the
‰
vicinity while handling petrol. Avoid spilling petrol onto a hot engine. Comply with all laws regulating storage and handling of fuels.
WARNING! Risk of burns. DO NOT touch the exhaust system or the drive unit.
‰
WARNING! NEVER refuel when the engine is running or when the engine is hot. Allow cool down time.
‰
Operate the chipper only on level surfaces (maximum allowable tilt is 10º) and where it will not be exposed to excessive moisture, dirt
9
or corrosive vapours or be in the proximity of combustible material (flammable liquids, solids or gases).
Only operate the chipper in well ventilated areas / environments.
9
DO NOT tip or change the chipper's position whilst it is operating.
8
Remove ill fitting clothing, ties, watches, rings and other loose jewellery and contain long hair. Wear appropriate protective clothing.
9
Keep non-essential persons and children away from the working area.
9
DO NOT use the chipper for any purpose other than that for which it is designed.
8
DO NOT operate the chipper if any parts are missing or damaged, as this may cause failure and/or personal injury.
8
DO NOT over-fill fuel tank. Always leave room for fuel to expand.
8
▲ DANGER! DO NOT tamper with the engine governed speed setting. Higher operating speeds are dangerous and increase the risk of
personal injury and/or equipment damage. Operating at excessively low speeds may result in shortened engine life. Over-speeding will
invalidate the warranty.
DO NOT operate the chipper when you are tired, or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT store chipper with fuel in tank where petrol vapours might reach an open flame or spark.
8
OPERATIONAL SAFETY
DO NOT allow children to operate this equipment.
8
DO NOT operate this equipment in the vicinity of bystanders. Keep bystanders away.
8
DO NOT run engine powered machines in an enclosed area since the exhaust from an engine contains carbon monoxide, which is
8
colourless, odourless, and tasteless. Carbon monoxide can be extremely dangerous in enclosed areas.
Wear ear protection and safety glasses at all times while operating the machine.
9
Avoid wearing clothing that is loose fitting or that has hanging cords or ties.
9
Only operate the machine in open space (e.g. not close to a wall or other fixed object) and on a firm, level surface.
9
DO NOT operate the machine on a paved or gravel surface where ejected material could cause injury.
8
Before starting the machine, check that all screws, nuts, bolts, and other fasteners are properly secured and that guards and screens
9
are in place. Replace damaged or unreadable labels.
Use extra care in handling fuels. They are flammable and the vapours are explosive. The following points should be observed:
9
: use only an approved container.
: never remove the fuel cap or add fuel while power source running.
© Jack Sealey Limited
WOOD CHIPPER, 420CC, 15HP, 100MM
CAPACITY
MODEL NO:
Wear protective
Wear safety
gloves
footwear
Ensure Good
Danger:
Ventilation
Rotating Blades
Original Language Version
SWC420
Wear protective Wear ear
clothing protection
Electric Shock Switch Off engine Before
Hazard
Hot surfaces Do not cover
Refuelling
SWC420 Issue 1 07/11/23