Sealey BC1000.V3 Quick Start Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instructions protection
1. SAFETY
Ensure that the beam clamp is in sound condition and good working order. Take action for immediate repair or replacement of damaged
9
parts. Use recommended parts only. The use of unauthorised parts may be dangerous and will invalidate the warranty.
Ensure the support beam for the beam clamp is capable of withstanding a load of at least 1½ times the beam clamp safe working load.
9
Keep the beam clamp clean for best and safest performance.
9
Locate the beam clamp in a suitable, well lit work area.
9
Keep work area clean and tidy and free from unrelated materials.
9
Ensure all non-essential persons keep a safe distance whilst the beam clamp is in use.
9
Use a qualified person to maintain the beam clamp.
9
DO NOT exceed the rated capacity (safe working load) of the beam clamp. Sudden load movement may briefly create excess load
8
causing product failure.
DO NOT use the beam clamp for purposes other than that for which it is intended.
8
Store the beam clamp in a dry, childproof area when not in use.
9
Always ensure that the load to be slung does not exceed the rated capacity of the equipment being utilized. Also ensure that the structure
9
to which the trolleys, clamps, hoists or blocks are attached meet or exceed the safety parameters as specified by the HSE.
The supporting structure the hoist is mounted to (including trolley, monorail, or crane) must be designed to withstand the loads and forces
9
imposed by the hoist for the rated load.
Install in location that allows the operator to move and stay clear of the load.
9
Raise test loads only to the minimum extent needed and stay well clear of load at all times during testing.
9
Wear goggles, hard hat, and steel-toed work boots during set up and use.
9
Sealey beam clamps can be used within an operating temperature range of -10°C to +55°C.
9
DO NOT allow children to play with or near this item.
8
Use as intended only. DO NOT use to handle molten material. DO NOT use for aircraft purposes.
9
DO NOT allow the load to swing during operation and DO NOT subject the equipment, chains or straps to shock loads.
8
DO NOT lift people or lift loads over people. Falling loads can injure or kill people.
8
DO NOT operate Beam Clamp with anything other than manual power (by hand).
8
DO NOT operate Beam Clamp with dangerous goods (e.g. molton masses, radioactive materials).
8
DO NOT remove or cover warning labels and/or tags. These carry important safety information. If unreadable or missing, contact
8
Customer Service Centre for a replacement.
WARNING! Failure to heed safety and warning instructions may result in damage and/or personal injury and will invalidate the warranty.
‰
NOTE: Ensure you have read and understood the safety instructions at the beginning of this section before you operate the beam clamp.
2. GENERAL
2.1. IDENTIFICATION/SUPPLIER
Sealey Power Products,
Kempson Way,
Suffolk Business Park,
Bury St Edmunds,
Suffolk, IP32 7AR.
Model No's: BC1000.V3, BC2000.V3, BC3000.V3
3. INTRODUCTION
Suitable for semi-permanent attachment to steel beams and acts as a lifting point for chain blocks, hoists and lifting tackle.The clamp
may also be used for lifting and transfer of steel beams and as a pulling clamp. Low profile afforded by integral pivot/lifting Point. All steel
structure. Powder paint coated for rust resistance.
4. SPECIFCATION
Note: Letters refer to dimensions shown in fig.1. On next page.
© Jack Sealey Limited
BEAM CLAMPS
MODEL NO'S:
Wear safety Wear head
footwear protection
Original Language Version
BC1000.V3, BC2000.V3, BC3000.V3
BC1000.V3, BC2000.V3, BC3000.V3, Issue:2 27/02/24