Advertisement
7.2.2. The beam clamp must be examined immediately if it has been subject to an abnormal load or shock. It is recommended that such an
examination is made by an authorised service agent.
7.2.3. Unauthorised parts may be dangerous and will invalidate the warranty.
Note! Please see the Definition of 'inspection' and 'examination' below.
7.3.
INSPECTION
7.3.1. Looking at the beam clamp for defects and checking the beam clamp for any signs of weakness. This is much more than a check but does
not require any part of the beam clamp to be dismantled other than removal from the beam.
7.4.
EXAMINATION
7.4.1. Verification that the beam clamp can safely continue in service. An examination is more thorough than an inspection.
7.5.
OWNER/ OPERATOR'S RESPONSIBILITIES
7.5.1. The owner and/or operator shall study these instructions and retain them for future use.
7.6.
UNDERSTANDING INSTRUCTIONS AND WARNINGS
7.6.1. The owner and/or operator shall understand the operating instructions and warnings before operating the beam clamp. Warning
information must be emphasised and understood. If the operator is not fluent in English, the product instructions and warnings must
be read to, and discussed with, the operator in the operator's native language by the owner, making sure the operator understands the
contents.
7.7.
DAMAGED BEAM CLAMPS
7.7.1. Any beam clamp which appears to be damaged, badly worn, or operates abnormally MUST BE REMOVED FROM SERVICE! It is
recommended that necessary repairs be made by an authorised service agent.
7.8.
STORAGE
7.9.
The equipment should ideally be stored in a purpose designed facility where it can be kept secure from unauthorised use. A
responsible person should control the issue and receipt of all lifting appliances and accessories, and a system to manage statutory
inspections should be in place.
7.10.
Storage would normally be on suitable racks within a container a manner that prevents accidental damage.
1. Never return damaged beam clamps to storage. The equipment should be dry, clean and protected from corrosion.
2. Store beam clamps on a rack and not lying on the ground. The storage area should be dry, clean and free from contaminates which
could harm the equipment.
3. If a beam clamp is permanently installed on a beam, it should be protected from the elements as far as possible.
7.11.
During transport to the worksite and whilst in store at the worksite, the equipment should be protected from exposure to any conditions
which may affect its ability to operate safely. In particular, it should be protected from exposure to• water/sea water;
Temperatures higher than can be comfortably tolerated by the hand.
9
Temperatures below freezing point.
9
Solvents.
9
Corrosive chemicals or fumes.
9
Grit, sand and wind-blown dust.
9
Any defects should be reported to the responsible person.
9
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be
sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When
the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved
containers and dispose of the product and fluids according to local regulations.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts
without prior notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please
email or call our technical team on technical@sealey.co.uk or 01284 757505.
IMPORTANT: No Liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
© Jack Sealey Limited
sales@sealey.co.uk
Original Language Version
www.sealey.co.uk
BC1000.V3, BC2000.V3, BC3000.V3, Issue:2 27/02/24
Advertisement
