Summary of Contents for Rlaarlo CT-8A
- Page 1 INSTRUCTION MANUAL MODEL NO.: CT-8A BUILT-IN GYRO DIGITAL PROPORTIONAL RADIO CONTROL SYSTEM CONTACT INFO.: support@rlaarlo.com WWW.RLAARLO-RC.COM...
- Page 2 1.SAFETY STATEMENT - Never operate your model during adverse weather conditions. Poor visibility can cause disorientation and loss of control of your model. - Never use this product in a crowd and illegal area. - Always ensure the trim levers at 0 and battery properly charged before connecting the receiver. - Always check all servos and their connections prior to each run.
- Page 3 4.PACKING LIST ITEM NAME QUANTITY REMARK Transmitter 1 piece Receiver 1 piece Type-C Cable 1 piece Battery Voltage Feedback Cable 1 piece Gift Box 1 piece 5.TRANSMITTER 5.1 TRANSMITTER INTRODUCTION Built-in Antenna Type-C Port for Charging / Trainer Mode Port / Firmware Updating Steering Wheel Operation Panel /...
- Page 4 Channel A Channel B Timer RSSI Return Voltage RX Vol RSSI TX Vol Transmitter voltage Channel 1 Channel 2 Channel 4 Channel 3 Channel 6 Channel 5 Channel 8 Channel 7 Power Button Channel A Channel C Channel B Channel D Scroll Key Power Button: 1.Long Prss: Turn on and off the...
-
Page 5: Interface: Model
5.2 Basic function introduction Interface: Model Total 8 groups to store the model data. Select Name Rename each group. Copy Copy the model data to another group. Reset Reset the set model data. Interface: Channel Set the operation reverse for each channel. Phase Range Adjust the Max. - Page 6 5.3 Code matching Enter the Code Matching interface through “Radio”--> “Pairing”. The transmitter has 2 code matching methods, you can choose one of them: Method 1: A.Power on the receiver first; B.Press the BINDING BUTTON on the receiver; C.Finally, turn on the transmitter. Method 2: A.Power on both the receiver and transmitter;...
- Page 7 5.5 Coach mode Enter the Coach Mode interface through “Radio”--> “Training”. The transmiter is equipped with a Type-C data cable, and 2 same transmitters can be directly connected with this cable to activate the coaching function. The transmitter can be set as “Slave” role or “Master” role, the transmitter in “Master”...
- Page 8 5.7 Programming mixing Enter the programming mixing control interface through “MIX Setup”--> “Program”. Programming mixing control is mainly for the mixing control mode of channel A/B and channel C/D, which can be applied to the raising and lowering of the winch of model cars. MIX Setup Programme 3 / 5...
-
Page 9: Battery Setting
5.9 Battery setting Enter the Battery Setting interface through “System”--> “Battery Type”--> “AUTO” / “4AA” / “2S ” / “1S ” The transmitter can be powered by 3 types of batteries: 4 pcs of AA batteries / 2S Lithium battery / 18650 battery. Please pay attention to the positive and negative poles when installing the batteries, and the transmitter has a battery reverse protection function. -
Page 10: Magic Control
5.10 Cruise speed Enter the Cruise Speed interface through “MIX Setup”--> “ESC Setup”--> “CCS”. When the value of “CCS” is set to “ON”, a white icon will be displayed on the main interface. When the product is under Cruise Speed Mode, the icon will change to green color. Operation Instructions: 1: Hold the throttle trigger at the fixed speed value for 3 seconds, enter the cruise control function, and the icon become green;... -
Page 11: Timer Setup
5.12 Timer Enter the Timer setting interface through “System”--> “Timer”. The maximum timer is 60 minutes. Press the throttle trigger or direction stick to start the timer function. During the timing process, you can long press the scrollwheel button to pause, long press again can press clear the timer. -
Page 12: System Settings
5.15 System settings The battery type of the transmitter can be selected. The default automatic shutdown time of the transmitter is 15minutes. Turning on the setting lock can lock all setting functions. The higher the standby brightness, the more power the transmitter uses. 6.PARAMETER ITEM NAME ITEM NAME... -
Page 13: Servo Mode
7.RECEIVER 7.1 Receiver introdction Servo Mode Light Positive Pin Signal Pin Negative Pin Channel 1 Channel 2 Channel 3 Channel 4 Channel 5 Channel 6 Channel 7 Channel 8 Signal Indicator Light Battery Voltage Feedback Port Binding Button 7.2 Servo mode Press the Bind Button for 3 seconds, the blue light on the receiver will be on. - Page 14 7.5 Built-in gyro function view × √ MODEL: CT-8A FCC ID: 2BDLE-CT-8A MADE IN CHINA - 14 -...
- Page 15 - 14 -...
Need help?
Do you have a question about the CT-8A and is the answer not in the manual?
Questions and answers
how to setup external gyro