Advertisement
Scanner Features and Presentation Mode
- LED
- Scan Window
- Scan Trigger
Aiming - Right/Wrong
Scanning
Hand-Held
Hands-Free (Presentation)
Connect Host Interface
NOTE: Cables may vary depending on configuration.
USB
Scan ONE of the bar codes below. The digital scanner automatically detects the host interface type and uses the default setting. If the default (*) does not meet your requirements, scan another host bar code below.
*USB Keyboard HID
IBM Hand-Held USB
IBM OPOS (IBM Hand-Held USB with Full Scan Disable)
Symbol Native API (SNAPI) with Imaging Interface
RS-232
Scan ONE of the bar codes below. The digital scanner automatically detects the host interface type and uses the default setting. If the default (*) does not meet your requirements, scan another host bar code below.
*Standard RS-232
ICL RS-232
Wincor-Nixdorf RS-232 Mode A
Wincor-Nixdorf RS-232 Mode B
OPOS/JPOS
Fujitsu RS-232
Keyboard Wedge
Scan ONE of the bar codes below. The digital scanner automatically detects the host interface type and uses the default setting. If the default (*) does not meet your requirements, scan the IBM PC/AT and IBM PC COMPATIBLE bar code below.
IBM PC/AT & IBM PC Compatibles
*IBM AT Notebook
IBM 46XX
Scan ONE of the bar codes below. The digital scanner automatically detects the host interface type, but there is no default setting. Scan one of the bar codes below to select the appropriate port.
Hand-Held Scanner Emulation (Port 9B)
Non-IBM Scanner Emulation (Port 5B)
Table-Top Scanner Emulation (Port 17)
Useful Bar Codes
Set Defaults
Set Factory Defaults
Add a Tab Key
Tab Key
Add an Enter Key
Add Enter Key (Carriage Return/Line Feed)
USB Caps Lock Override
Override Caps Lock Key (Enable)
User Indications (By Default)
Tab 1
| Indication | Beeper Sequence | |
| Power up | Low/medium/high beep | |
| Bar code is successfully decoded | Short high beep | |
| Transmission error | 4 long low beeps | |
| Successful parameter setting | High/low/high/low beep | |
| Correct programming sequence performed | High/low beep | |
| Incorrect programming sequence, or Cancel | Low/high beep | |
Tab 2
| Indication | LED Indicator |
| Hand-Held Scanning | |
| Scanner is on and ready to scan, or no power to | Off |
| Bar code is successfully decoded | Green |
| Transmission error | Red |
| Hands-Free (Presentation) Scanning | |
| No power to scanner | Off |
| Scanner is ready to scan | Green |
| Bar code is successfully decoded | Off momentarily |
| Transmission error | Red |
123Scan
123Scan is an easy-to-use, PC-based software tool that enables rapid and easy customized setup of a scanner via a bar code or USB cable. For more information, visit: http://www.zebra.com/123Scan.
Utility Functionality
- Device configuration
- Electronic programming (USB cable)
- Programming bar code(s)
- Data view - scan log (display scanned bar code data)
- Access asset tracking information
- Upgrade firmware and view release notes
- Remote management (SMS package generation).
Troubleshooting
Aiming line does not appear
| No power to scanner | Connect scanner to powered host, or connect power supply |
| Aiming line is disabled | Enable aiming line |
Scanner decodes bar code but does not transmit data
| Interface cable is loose | Reconnect the cable |
| Transmission or format error | Set the proper communication and conversion parameters |
| Invalid ADF rule | Program the correct ADF rules |
Scanner does not decode bar code
| Scanner not programmed for bar code type | Enable that bar code type |
| Bar code is unreadable | Ensure the bar code is not defaced; scan a test bar code of the same bar code type |
| Bar code is out of aiming line area | Move the aiming line over the bar code |
Scanned data incorrectly displayed on host
| Host interface not configured properly | Scan appropriate host parameter bar codes |
| Region improperly configured | Select appropriate country and language encoding scheme |
RECOMMENDED USAGE GUIDE - OPTIMUM BODY POSTURE
LED Devices
Classified as 'EXEMPT RISK GROUP' according to IEC 62471:2006 and EN 62471:2008. Pulse duration: 9 ms.
Power Supply
Use ONLY a Zebra approved UL LISTED ITE (IEC/EN 60950-1, LPS/SELV) power supply with electrical ratings: Output 5.2Vdc, min 1.1A, with a maximum ambient temperature of at least 50 degrees C. Use of alternative power supply will invalidate any approvals given to this unit and may be dangerous.
Service Information
If you have a problem using the equipment, contact your facility's Technical or Systems Support.
If there is a problem with the equipment, they will contact the Zebra Global Customer Support Center at: http://www.zebra.com/support.
For the latest version of this guide go to: http://www.zebra.com/support.
Documents / Resources
References
Download manual
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download Zebra DS2208 - DS2200 Series Digital Scanner Quick Start Manual
Advertisement
Need help?
Do you have a question about the DS2208 and is the answer not in the manual?
Questions and answers