Yamaha GX-50 Owner's Manual page 43

RECORDING COMPACT DISCS
1
MINI COMPONENT SYSTEM
GX–50
1
2
3
LOCATION
MUSIC
TUNER
BAND
USER MEMORY
TAPE 1/2
REC/PAUSE
MODE
DOLBY NR
POWER
PHONES
TIMER REC
AUTO/MAN'L
TIME
1 2
1 2
6 7
6 7
A B
TIME PROG
MODE REPEAT
DISC SKIP
3
LOCATION
MUSIC
7
USER
SLEEP
4
Display information during programming
Side of the tape
TAPE 1 2
1 2 3 4
5 6 7 8
9 10 11 12
13 14 15
OVER 15
PRESET
TRACK T REM
Next playback order
Programmed track numbers light up
and unprogrammed ones flash.
TAPE 1 2 1 2 3 4
5 6 7 8
9 10 11 12
13 14 15
OVER 15
PRESET
T REM
TRACK
Selected track Total remaining time on
number the side of the tape
9 1
DISC CHANGE
OPEN/CLOSE
VOLUME
CD
DOWN UP
AUX
NORMAL
HIGH
DUBBING
MEMORY
Active Servo
Technology
CD
3 4 5
3 4 5 5
8 PRESET
8 9 0
C D E
TAPE EDIT + I0
TUNER
RANDOM OPEN/CLOSE
STOP PLAY/PAUSE
PLAY STOP PLAY
TAPE
FLAT REC/PAUSE DECK 1/2
POWER
INPUT
9
VOLUME
1
1
Selected disc
EDIT
A B
PROG
RANDOM
S F REP VOLUME
Hz
K
MHz
EDIT
A B
PROG
RANDOM
S F REP
VOLUME
Hz
K
MHz
To record programmed tracks from one or
more discs
1
Press the CD input selector button and load a disc (or
discs) on the disc table.
2
Follow steps 3–6 on page 31.
3
Press the PROG button.
* "PROG" and "P-01" will light up on the display, and all
track numbers on the selected disc will begin flashing.
4
If necessary, select a desired disc by pressing the DISC
SKIP button.
5
Select the desired track number by pressing the track
number input buttons.
6
Repeat steps 4 and 5 to program more selections for the
side A of the tape. You can select the same track again.
* Pressing the TIME button displays the total remaining
time on the side of the tape for about 1 second, and
then it is replaced by the display of the next playback
order.
* If "TM OVER" appears on the display, the track number
just selected cannot be programmed because there is
not enough time remaining on the side A of the tape.
However, at this time, if any other track number is
flashing continuously on the display, you can program
it instead of the unprogrammable one.
7
After you finish the programming for the side A, press the
TAPE button.
* "PU SET" appears on the display, then you can begin
programming for side B.
* After this step is done, you can check the programmed
contents for side A and side B alternately by pressing
the TAPE button at any time before you press the EDIT
button in step 9.
8
Repeat steps 4 and 5 to program selections for the side B
of the tape. You can select the same track again.
* If "TM OVER" appears on the display, the track number
just selected cannot be programmed because there is
not enough time remaining on the side B of the tape.
However, at this time, if any other track number is
flashing continuously on the display, you can program
it instead of the unprogrammable one.
9
Press the EDIT button. ("EDIT" appears on the display.)
The recording is automatically started.
Notes on tape-editing
•
If programs are made selecting tracks from more than one
disc, during recording, the DISC CHANGE button on the
CD player is disabled.
•
To check, cancel or correct program data, refer to page
14.
•
The maximum number of tracks that can be programmed
is 20.
•
This function can be used to program up to track number
15. If the disc has more than 15 tracks, track number 16
and thereafter will not be programmed.
E-33