Cub Cadet 7264 Operator's Manual
  1. Manuals
  2. Brands
  3. Cub Cadet Manuals
  4. Tractor
  5. 7264
  6. Operator's manual
Cub Cadet 7264 Operator's Manual

Cub Cadet 7264 Operator's Manual

Cub cadet compact tractor operator's manual 7000 series
Hide thumbs Also See for 7264:
Table of Contents

Advertisement

Quick Links

Operator's Manual
COMPACT TRACTOR
MODEL 7264
IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY
Warning
: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved
forest-covered, brush-covered or grass-covered land unless the engine's exhaust system is equipped with a spark
arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective
working order by the operator. In the State of California the above is required by law (Section 4442 of the California Public
Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester for the
muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box
361131Cleveland, Ohio 44136-0019.
CUB CADET LLC P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 [www.cubcadet.com]
PRINTED IN U.S.A.
FORM NO. 769-00002
(5/02)

Advertisement

Table of Contents
loading

Related Manuals for Cub Cadet 7264

Summary of Contents for Cub Cadet 7264

  • Page 1 Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 361131Cleveland, Ohio 44136-0019. CUB CADET LLC P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 [www.cubcadet.com] PRINTED IN U.S.A. FORM NO. 769-00002...

  • Page 2: Table Of Contents

    The dealer has trained service personnel familiar with the latest servicing information, is equipped with the latest tools, and has a complete line of genuine Cub Cadet service parts which assure proper fit and high quality.

  • Page 3: Recording Model And Serial Number Information

    Serial Number ROPS Information Plate: ROPS Serial No. TRACTOR MODEL PLATE XXXXXXXXXXX XXXXXXXXXX Model Number Mfg. Date CUB CADET LLC P. O. BOX 361131 www.cubcadet.com CLEVELAND, OH 44136 DEALER LOCATOR PHONE NUMBER: 877-282-8684 Mfg. Date (Serial No.) Type Date Code...

  • Page 4: Important Safe Operation Practices

    IMPORTANT SAFE OPERATION PRACTICES WARNING: THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF NOT FOLLOWED, COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OF YOURSELF AND OTHERS. READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE YOUR UNIT. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.

  • Page 5: Slope Operation

    • Maintain the weight balance of the tractor. Install front end weights to counterbalance heavy implements attached to the three point hitch. Do not operate the tractor with a light front end. • Any towed vehicle with a total weight exceeding that of the tractor should be equipped its own braking system that is operational from the tractor seat.
  • Page 6 • To prevent injury, do not adjust, unclog, clean, or service PTO driven equipment while the tractor engine is running. • Make certain all PTO shields are always installed. 5. SAFETY FRAME (ROPS) Your tractor is equipped with a rollover protective structure (ROPS) which must be maintained in a fully functional condition.

  • Page 7: Safety Labels

    SAFETY LABELS 1. KNOW THE OPERATING AND SAFETY INSTRUCTIONS IN THE OPERATORS'S MANUAL AND ON THE TRACTOR. MOVE THROTTLE TO MID POSITION AND DEPRESS BRAKE PEDAL. TURN KEY TO THE START POSITION. DISENGAGE PTO AND SET PARKING BRAKE. MOVE THROTTLE CONTROL TO MID POSITION AND TURN KEY OFF. •...
  • Page 8 SAFETY LABELS (Cont.) To avoid personal injury, keep PTO shield in place. Pull only from draw bar. pulling from any other point can cause rear overturn. Disengage PTO and stop engine before servicing tractor, or implements, or attaching or detaching implements. FAILURE TO FOLLOW ANY OF THE INSTRUCTIONS ABOVE CAN CAUSE SERIOUS INJURY TO THE OPERATOR, OR OTHER PERSONS.

  • Page 9: Section 1: Controls And Features

    SECTION 1: CONTROLS AND FEATURES FLOORBOARD AND DASH PANEL MOUNTED CONTROLS Steering Wheel PTO Switch Throttle Handle Ignition Switch Brake Pedal Forward/Reverse Pedal * Steering Wheel and Seat Phantomed For Clarity Figure 1 Seat Adjustment Lever Differential Lock Pedal Parking Brake Lever Hazard Light Switch Headlight Switch Instrument Panel...
  • Page 10 NOTE: References to LEFT and RIGHT indicate that side of the tractor when facing forward while seated in the drivers seat. Reference to FRONT indicates the grille end of the tractor; to REAR, the drawbar end. A. Steering Wheel The steering wheel is centered on the dash panel. It is used to change the direction (left or right) of the tractor while driving.
  • Page 11 H. Differential Lock Pedal Diff. Lock Pedal Symbol Figure 6 Located at the rear of the left floor board, the differential lock pedal engages the transmission differential lock. The differential lock is used to gain additional trac- tion when operating the tractor on wet or loose soil. When the pedal is depressed the rear wheels of the tractor are prevented from rotating independently of one another.
  • Page 12 If this warning lamp comes on during operation, check the charging system for possible causes and/or contact your Cub Cadet dealer. 4. Engine Oil Pressure Light The bulb illuminates when the ignition switch is in the ON position and should turn off shortly after the engine is started.
  • Page 13 FENDER MOUNTED CONRTOLS AND FEATURES Fuel Fill Cap PTO Reverse Override Switch PTO Selection Lever Hydraulic Lift Lever Trans. Hi/Lo Shift Lever Cup Holder A. Fuel Fill Cap The fuel fill cap is located on the left fender beside the operator’s seat. WARNING: Never fill the fuel tank to the top of the filler neck.
  • Page 14 E. Transmission Hi/Lo Range Shift Lever The Hi/Lo range shift lever is located on the right fender. The lever has two speed range settings and a neutral position. The lever must be shifted into either the high or low range prior to depressing the forward/reverse pedal to drive the tractor.

  • Page 15: Section 2: Operation

    • In the event of an accident, have the ROPS carefully inspected and, if necessary, replaced by your Cub Cadet dealer. Do not attempt to repair the ROPS. FOLDING THE ROPS The foldable ROPS feature allows the operator to quickly lower the ROPS to operate in areas where there is low overhead clearance.
  • Page 16 SAFETY INTERLOCK SYSTEM This tractor is equipped with a safety interlock system for the protection of the operator. If the interlock system should ever malfunction, do not operate the tractor. Contact your authorized Cub Cadet Dealer. The safety interlock system prevents the engine from cranking or starting unless the brake pedal is fully depressed, and the PTO is “OFF”.
  • Page 17 Follow the normal engine starting instructions above. • An optional engine coolant heater is available from your Cub Cadet dealer. This heater will aid in starting the tractor when ambient temperatures fall below 10°F (-12°C). USING JUMPER CABLES TO START THE...
  • Page 18 DRIVING THE TRACTOR WARNING: Avoid sudden starts, exces- sive speed and sudden stops. WARNING: Do not leave the seat of the tractor without disengaging the PTO and engaging the parking brake. If leaving the tractor unattended, turn the ignition key off and remove key. •...
  • Page 19 • To move in reverse, check that the area behind is clear then slowly depress the rear of the forward/reverse pedal. PARKING BRAKE LEVER FORWARD/ REVERSE PEDAL Figure 15 • When traveling short distances with frequent changes in direction, the forward/reverse rocker pedal may be operated using the heel/toe method.
  • Page 20 • Fully depress and hold the differential lock pedal to engage the transmission differential lock. Release the pedal to disengage the differential lock. See Figure 17. DIFFERENTIAL LOCK PEDAL (Depress and Hold to Engage) Figure 17 NOTE: Because of the drive load on the internal engagement mechanism, releasing the differential lock pedal...
  • Page 21 • Shift the PTO lever forward to select the mid PTO. The mid PTO is used to drive equipment designed to operate at an input speed of 2000 RPM. Refer to Figure 19. • Shift the PTO lever to the middle position to select both the mid PTO and rear PTO.
  • Page 22 Hazard Lights Always use the flashing amber hazard lights along with the SMV (Slow Moving Vehicle) emblem when operating the tractor on, or near, roadways. Also activate the hazard lights when necessary to warn others that the tractor is being operated in the area. •...
  • Page 23 Front Weights To counterbalance three point hitch mounted equipment, a weight bracket/bumper kit and cast iron weights are available from your Cub Cadet dealer. When mounting Cub Cadet equipment such as the 50" rotary tiller; 48" rotary cutter; or the 60" finish mower, the weight bracket and a minimum of four suitcase weights should be used.

  • Page 24: Section 3: Adjustments

    SECTION 3: ADJUSTMENTS ADJUSTING THE SEAT For the comfort of the operator, a single lever adjustable seat is provided to set the fore to aft position of the seat. Adjust the seat to the most comfortable position that allows you to operate all controls and pedals.
  • Page 25 • The length of the upper hitch link is normally determined by the design of each implement. To adjust the upper hitch link, loosen the jam nut and turn the adjustment tube as shown in Figure 25. After the appropriate length is at- tained, tighten the jam nut.
  • Page 26 Because of the precise nature of the feedback rod adjustment, it is recommended that any adjustment be per- formed by a qualified mechanic at your Cub Cadet dealer. If a high pitched squeal continues to emit from the...

  • Page 27: Section 4: Tractor Maintenance

    CF-4 Above 32°F Hydraulic Transmission Fluid Approx. 12 Qts. (6 Gal.) Approx. Use Cub Cadet Gear Lube 81 Oz. (2.5 Qts.) Needed 737-3034 (14.5 Oz. Cartridge) Use High Quality Permanent Type Antifreeze Approx. (Ethylene Glycol with corrosion and rust 5.3 Qts.
  • Page 28 LUBRICATION AND MAINTENANCE CHART (ILLUSTRATION)

  • Page 29: Lubrication And Maintenance Chart

    LUBRICATION AND MAINTENANCE CHART Ref. Operation to be Performed Check Engine Oil Level Check Air Cleaner Check Engine Coolant Level Check and Clean Radiator Screen and Oil Cooler Fins Change Engine Oil and Replace Oil Filter Retorque Front and Rear Wheel Bolts Check Transmission Oil Level Replace Hydraulic and...
  • Page 30 ACCESSING THE ENGINE COMPARTMENT WARNING: If the tractor has been recently operated, engine surfaces (including the radiator) will be HOT. Allow the engine to cool before open- ing the hood, or use extreme caution to avoid burns when the hood is open. To raise the hood, locate the latch release lever in the hood notch at the front of the tractor.
  • Page 31 • Since battery acid is corrosive, do not pour it into any sink or drain. Before discarding an empty electrolyte container, rinse it thoroughly with a neutralizing solution. • NEVER connect (or disconnect) battery charger clips to the battery while the charger is turned on, as it can cause sparks.
  • Page 32 TAIL LIGHT BULB REPLACEMENT Each tail light assembly has two light bulbs — a reverse indicator bulb (Cub Cadet no. 725-3263) and a tail light (Cub Cadet no. 725-3262). Access the back side of the tail lights from under the rear fender.
  • Page 33 If the electrical system does not func- tion, check for blown fuses. See Figure 37 If you have a recurring problem with blown fuses, have the tractor’s electrical system checked by your Cub Cadet dealer. GOOD Figure 37 Accessing the Fuse Center The fuse center is located on the inside right of the dash panel.
  • Page 34 Main Fuse The main fuse in the tractor wire harness protects the tractor’s entire electrical system. A blown main fuse will prevent battery current from passing though the harness. To replace the main fuse: • Raise the tractor hood and remove the right side panel.

  • Page 35: Changing Transmission/Hydraulic System Oil

    • If the oil level is low, add Cub Cadet hydraulic oil. Loosely position a funnel in the fill hole so that there is enough clearance around the fun- nel to allow the transmission to vent while the oil is poured into the transmission. Fill ONLY to the full mark, never overfill the transmission.
  • Page 36 CHANGING HYDROSTATIC TRANSMISSION AND HYDRAULIC SYSTEM OIL FILTERS NOTE: Except for the initial break-in period oil filter change, the hydrostatic transmission and hydraulic system oil filters should be changed along with the hydrostatic transmission/hydraulic system oil after every 200 hours of operation. Initial Break-In Period Filter Change During the initial hours of tractor operation, contam- inants caused by the normal break-in of internal...
  • Page 37 (See Figure 44). • If the oil level is low, add only enough Cub Cadet Gear Lube to bring the level to the full mark on the dipstick. NEVER overfill the axle housing.
  • Page 38 Reinstall the drain plug after draining the oil. See Figure 46. • Fill the axle with Cub Cadet Gear Lube until the oil level reaches the full mark on the dipstick. Do not over fill the axle housing.
  • Page 39 TIRE MAINTENANCE Check the tire air pressure after every 50 hours of operation or weekly. Keep the tires inflated to the recommended pressures. Improper inflation will shorten the service life of a tire. See the tire side wall, or the Tire Inflation chart, for proper inflation pressures.
  • Page 40 3. Clean the engine and the entire tractor thoroughly. 4. Fill the fuel tank with FRESH high grade Number Two diesel fuel. 5. Remove the glow plugs and pour a small amount of engine oil into each cylinder. Reinstall the glow plugs and slowly crank the engine to distribute the oil.

  • Page 41: Section 5: Engine Information And Maintenance

    SECTION 5: ENGINE INFORMATION AND MAINTENANCE Daihatsu L.L.C., the California Air Resources Board (CARB) and the United States Environmental Protection Agency (U.S. EPA) (Owner’s Defect Warranty Rights and Obligations) EMISSION CONTROL WARRANTY COVERAGE IS APPLICABLE TO CERTIFIED ENGINES PURCHASED IN CALIFORNIA IN 1995 AND THEREAFTER, WHICH ARE USED IN CALIFORNIA, AND TO CERTIFIED MODEL YEAR 2000 AND LATER ENGINES WHICH ARE PURCHASED AND USED ELSEWHERE IN THE UNITED STATES California And United States Emission Control Defects Warranty Statement...
  • Page 42 c. Ignition System For Gasoline • Spark plug(s) • Ignition coil • Ignition processor d. Exhaust System • Exhaust manifold e. Miscellaneous Items Used in Above Systems • Vacuum, temperature, position, time sensitive valves and switches • Electronic controls • Connectors and assemblies •...
  • Page 43 ENGINE MAINTENANCE WARNING: Use care when servicing any component in the engine area. If the engine has recently been operated, components will be hot and could cause burns. Allow the engine to cool before servicing. WARNING: Before servicing the engine, place the tractor on a level surface, stop the engine, engage the parking brake, and remove the key from the...
  • Page 44 ADDING ENGINE OIL WARNING: Never overfill the engine crankcase. The engine may overheat and/or damage may result if the crankcase is below the “ADD” mark or over the “FULL” mark on the dipstick. For best results, fill to the “FULL” mark on the dipstick as opposed to adding a given quantity of oil.
  • Page 45 • Remove the filter by turning it counterclockwise using an automotive type filter wrench to loosen. See Figure 53. FUEL FILTER FILTER Figure 53 • Reinstall the drain plug in the engine and clean up any residual oil. Refer to Figure 52. •...
  • Page 46 • Start the engine and allow it to run for a short period. Stop the engine. • Recheck the coolant level in the overflow reservoir and refill as needed. Reinstall the reservoir cap. INSPECTION OF COOLING SYSTEM HOSES Check the cooling system hoses and fan belt for any cracks or deterioration after every 100 hours of operation.
  • Page 47 • Pull the air cleaner element from the housing. See Figure 56. CLEANER ELEMENT Figure 56 • Lightly blow or brush loose debris from the air cleaner element. Clean any debris from the housing. • Inspect the paper pleats of the cleaner element for damage and dirt.
  • Page 48 Changing The Fuel Filter Replace the fuel filter cartridge after every 600 hours of operation. NOTE: There is no shut off valve in fuel system. To stop the flow of fuel while replacing the filter, it will be necessary to carefully clamp the fuel line between the fuel tank and the filter.

  • Page 49: Section 6: Specifications

    Drive ............On Demand 4WD Transmission Oil ......Cub Cadet Hydraulic/Transmission Fluid Transmission Capacity (Includes Hydraulics) .

  • Page 50: Specifications

    SPECIFICATIONS Hydraulic Lift System Type ............Auxiliary Pump-Gear Control .

  • Page 51: Section 7: Optional Equipment And Accessories

    SECTION 7: OPTIONAL EQUIPMENT AND ACCESSORIES When purchasing your tractor, you probably had it equipped for your particular needs at that time. You may later wish to obtain additional equipment or accessories to perform other tasks. Refer to the chart below for a list of optional equipment and accessories currently available through your Cub Cadet dealer.

  • Page 52: Warranty

    This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Cub Cadet LLC reserves the right to make changes in the design and other changes in its products at any time without notice and without incurring any obligation to product previously manufactured or purchased.

Table of Contents