Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Brita mypure P1
Summary of Contents for Brita mypure P1
- Page 1 P1 Instructions for use...
- Page 2 Index I. Congratulations Page ENGLISH II. Quality from the very start Page 4 – 11 III. Important notes Page IV. BRITA, quality and satisfaction guaranteed Page...
- Page 3 I. Congratulations on your new BRITA ® system Thank you for choosing BRITA quality for cleaner, clearer great tasting BRITA iltered water straight from your BRITA Dispenser with BRITA Cartrdige Status Indicator. Your BRITA system offers many advantages BRITA iltered water •...
-
Page 4: Quality From The Very Start
Contents of the mypure P1 Compact Water Filtration System To ensure you get the best result from your mypure P1 Filtration System, please follow these instructions carefully. Your mypure P1 Filtration System includes the following (see ig. - Page 5 "A" symbol appears in the window (ig. 3). The ilter head contains a low regulator already installed. It guarantees Step 1: Selecting the carbonate hardness smooth water low from your BRITA Dispenser even at higher water pressures. setting (A/B/C) on the ilter head The ilter head offers three settings for medium hard water (A), hard water (B) and very hard water (C).
- Page 6 LED light lashes green, yellow and red. Make sure you push both buttons The three lights in the BRITA lever are only activated in the iltering at the same time.
- Page 7 BRITA Dispenser. Next, install the BRITA Dispenser (see ig. 6). Then put the base (2) over the hole and ix the BRITA Dispenser (1) in place using the supplied counter plate (4), the gasket (3), the locking ring (5) and the hexagon nut (6).
- Page 8 Hose 1: on the hose (1), use the supplied adapter if required. Your 3/8” 800 mm mypure P1 Filtration System comes with a 1/2" adapter. Please go to your nearest supplier for adapters in other sizes. Cold water C a) Put the hose (2) in place.
- Page 9 Step 5: Inserting the ilter cartridge (see ig. 8) Step 6 (optional): Space-saving wall mount to install the cartridge under the sink A Remove protective strap (1). (see ig. 8) (see ig. 9) B Insert the ilter cartridge (4) vertically into the ilter head (5). Please make sure the lush hose of the ilter head is at the outside.
-
Page 10: Maintenance
Regularly check the ilter system for leaks. Regularly check the B Open the valve on your BRITA Dispenser and rinse through until hoses for kinks. Kinked hoses must be replaced. the iltered water runs clear and without any bubbles (at least 2 litres). -
Page 11: Troubleshooting
Technical data of the P 1000 cartridge Troubleshooting A No water low Operating pressure 2 bar to max. 8.6 bar Cause: Water intake closed. Water intake temperature 4°C to 30°C Troubleshooting: Open the water intake at the upstream shut-off operation 4°C to 40°C valve or by closing the locking handle (3) on the Ambient tem-... -
Page 12: Important Notes
• BRITA recommends that the ilter system is not left unused for mechanical damage. Do not assemble near sources of heat and a long period. If the mypure P1 Filtration System is not used for open lames. A stop valve must be installed before the ilter system several days (2–3 days), we recommend that the ilter system be... -
Page 13: Exclusion Of Liability
Exclusion of liability BRITA shall not be held liable for any damage, including subsequent damage, arising from the incorrect use of the product. 100% satisfaction: the BRITA guarantee...
Need help?
Do you have a question about the mypure P1 and is the answer not in the manual?
Questions and answers