Related Manuals for Monacor RELACART MIXX12-D
Summary of Contents for Monacor RELACART MIXX12-D
- Page 1 Distribution of Relacart products w w w . r e l a c a r t . c o m www.monacor-international.com MONACOR INTERNATIONAL GmbH & Co. KG Zum Falsch 36, 28307 Bremen, Germany A-2162.00.01.02.2024...
-
Page 2: Table Of Contents
Quick Connect Guide Contents… … … … … … … … … … … … … … … … … … … … … … … … … … … … Quick Connect Guide … … … … … … … … … … … … … … … … … … … … … … … 2 Quick Connect Guide Product introduction …... -
Page 3: Product Introduction
Introduction of Mixer Panel Product introduction Front panel: MIXX12 / MIXX12-E is a digital mixer with 12 inputs and 10 outputs. It is a new mixer equipped with DANTE4 * 4 digital audio transmission module. You can use a network cable to connect to the router for wireless control, or use the built-in WIFI of the mixer 1. -
Page 4: Rear Panel
Instructions for using the interactive operation interface Rear panel: 1. AC power interface: Install the factory-configured power cord and connect 110V-240V 50 / 60Hz AC power. GAIN SHOW SYSTEM INPUTS OUTPUTS 2. Power switch: I / O boat switch, press I to turn on the power, press O to turn off the Analog Analog Analog... -
Page 5: Ch1-12 Input Channels
CH1-12 Input channels GAIN Analog GAIN SHOW SYSTEM INPUTS OUTPUTS GATE/COMP Analog Analog Analog Analog Analog Analog Analog Analog SENDS COMP GATE/COMP GATE/COMP GATE/COMP GATE/COMP GATE/COMP GATE/COMP GATE/COMP GATE/COMP SENDS SENDS SENDS SENDS SENDS SENDS SENDS SENDS MUTE SOLO MUTE MUTE MUTE MUTE... - Page 6 OUTPUTS Input equalizer: 4 - band parametric equalizer, of which BAND 1 and BAND 4 can be GAIN GAIN switched between shelves and bells, can be in the range Click "Equalizer", and when SHOW SHOW INPUTS OUTPUTS INPUTS OUTPUTS Analog Analog GATE GATE...
-
Page 7: Aux1-4 / Dante1-4 Auxiliary Output / Dante Output
AUX1-4 / DANTE1-4 Auxiliary output / DANTE output Click this button, the main interface area is displayed as shown in the figure Compressor: An amplifier that reduces its gain as the input signal level increases. AUX 1 GAIN SHOW MAIN AUX 1 - 6 INPUTS OUTPUTS... -
Page 8: Effect: Reverb / Echo
DELAY (Echo): Input equalizer: 4-band parametric equalizer, of which BAND 1 and BAND 4 can be Before Fader: Click this button to select Pre Fader, Post Fader, or Pre Dsp.(Before switched between the shelf and the bell shape, and the frequency, gain and Q value the fader) indicates that the signal is not limited by the fader. -
Page 9: Group: Grouping
GROUP: Grouping There are 4 mute groups and 4 control groups. After clicking GROUP, a pop-up picture Control grouping: After entering the control editing interface, as shown in the figure: is displayed, click "Edit", the main screen area enters the mute / control interface. click “Control 1”, select 1, 2, 3, 4 channels, then select the function you want to adjust at the same time, and then click the control group “1”... -
Page 10: Eeffect: Mixing / Echo Parameters
EEFFECT: mixing / echo parameters CLEAN SOLO After clicking this button, the monitoring function of all channels will be cancelled after 2 DELAY seconds. 0.0 dB GAIN SHOW INPUT INPUTS OUTPUTS Analog REVERB PRESET RESET CLEAN MUTE Delay 1 COMP Click this button to cancel the mute function of all channels after 2 seconds Delay 2 REVERB... -
Page 11: Main Output Controls
Main output controls Main output compressor: You can set a level point. Once the signal exceeds this Main output channel function: critical point, the volume will be attenuated and the overall volume will be stable, Input equalizer so as to avoid howling or overload the amplifier. Left and right channel adjustment COMP MAIN... -
Page 12: Troubleshooting Guide
Troubleshooting Guide Home screen area DANTE network port or WIFI operation steps are the same 1: Network connection between computer / tablet and MIXX12. GAIN SYSTEM SHOW INPUTS OUTPUTS Analog Analog Analog Analog Analog Analog Analog Analog COMP GATE/COMP GATE/COMP GATE/COMP GATE/COMP GATE/COMP... - Page 13 3 Switch to the help page and click Local Upgrade. Do not click repeatedly or you will 5 If the upgrade is unsuccessful, the Update fail prompt window appears. Please check get an error. After clicking, the firmware will start to upgrade, as shown below: the upgrade steps and upgrade again.
-
Page 14: Reset The Parameters After The Wifi Reset
Reset the parameters after the WIFI reset 4 Change the webpage to Chinese, click the HLK-RM04 page (see Figure 1) (Press and hold the RESET key for 3 seconds to reset the factory fixed IP address of PIC 1： HLK-RM04 Web Configure the DANTE network port. - Page 15 5 Wait for 20 seconds and search again for WIFI name: MIXX12, and the connection password is 12345678 12345678 6 After setting the WIFI parameters according to the above 5 steps, if you need to modify the WIFI name and password, or the connection software is abnormal, the IP that needs to re-enter the setting interface has changed: 192.168.11.254, the login account and password are also: admin 192.168.11.254...
Need help?
Do you have a question about the RELACART MIXX12-D and is the answer not in the manual?
Questions and answers