Acer H233H Product Service Manual
  1. Manuals
  2. Brands
  3. Acer Manuals
  4. Monitor
  5. H233H
  6. Product service manual
Acer H233H Product Service Manual

Acer H233H Product Service Manual

Hide thumbs Also See for H233H:
Table of Contents

Advertisement

Quick Links

Product Service Manual – H233H
Service Manual for acer: H233H
P/N : 9J.0W116.H1S
Applicable for All Regions
Version : 002
Date : 2009/05/18
Notice:
- For RO to input specific "Legal Requirement" in specific NS regarding to responsibility and liability
statements.
First Edition (May, 2009)
© Copyright Acer Corporation 2009. All Right Reserved.
- 1 -

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the H233H and is the answer not in the manual?

Questions and answers

Related Manuals for Acer H233H

Summary of Contents for Acer H233H

  • Page 1 Applicable for All Regions Version : 002 Date : 2009/05/18 Notice: - For RO to input specific “Legal Requirement” in specific NS regarding to responsibility and liability statements. First Edition (May, 2009) © Copyright Acer Corporation 2009. All Right Reserved. - 1 -...

  • Page 2: Table Of Contents

    Content Index Abbreviations & Acronyms ................3 1. About This Manual..................3 1.1 Trademark ......................3 2. Introduction ....................4 2.1 RoHS (2002/95/EC) Requirements ..............4 2.2 Safety Notice ....................4 2.3 Compliance Statement..................4 2.4 General Descriptions ..................4 3.

  • Page 3: Abbreviations & Acronyms

    Abbreviations & Acronyms 1. About This Manual This manual contains information about maintenance and service of acer products. Use this manual to perform diagnostics tests, troubleshoot problems, and align the acer product. Trademark The following terms are trademarks of Acer Inc. :...

  • Page 4: Introduction

    2. Introduction This section contains general service information, please read through carefully. It should be stored for easy access place for quick reference. 2.1 RoHS (2002/95/EC) Requirements – Applied to all countries require RoHS. The RoHS (Restriction of Hazardous Substance in Electrical and Electronic Equipment Directive) is a legal requirement by EU (European Union) for the global electronics industry which sold in EU and some counties also require this requirement.

  • Page 5: Product Overview

    3. Product Overview 3.1 Introduction H233H is defined as our new 23”W model in ACER H series which will be the ACER project in Qisda. H233H is defined as 23”W LCD Monitor supports 1920(H) x 1080(V) resolution with DPMS (Display Power Management System) and ACER eColor function. There are triple input types, D- sub, DVI, and HDMI.

  • Page 6: Operational Specification

    supported EMEA Multi-language supported for OSD Non-EMEA 7 buttons including 1 Buttons control supported monitor power on/off control button. Flywheel control supported Scaling function supported Auto adjustment function supported “Auto-Key” function DDC function supported (EDID ver. DDC2B 1.3) DDC-CI support version 1.1 or later DDC-CI Audio speakers supported Audio...
  • Page 7 3.2.2 Signal interface Item Condition Spec OK N.A Remark Color: Black √ 15-pin D-Sub Length: 1800 +/- 30 mm Signal Cable Color: Black √ 24-pin DVI-D Length: 1800 +/- 50 mm √ 15-pin D-sub connector See Note-1 For 15-pin D-sub √...
  • Page 8 Note-2: The pin assignment of 24-pin DVI-D connector is as below, Signal Assignment Signal Assignment TMDS RX2- Floating TMDS RX2+ +5V Power TMDS Ground Ground(Cable Detect) Floating Hot Plug Detect Floating TMDS RX0- DDC Clock TMDS RX0+ DDC Data TMDS Ground Floating Floating TMDS RX1-...
  • Page 9 Note-3: The pin assignment of 19-pin HDMI connector is as below, Note：Pin 11 is used as Cable Detect. - 9 -...
  • Page 10 3.2.3 Video performance Item Condition Spec OK N.A Remark Both for analog and √ Max. support Pixel rate 173 MHz digital inputs Both for analog and Max. Resolution √ 1920 x 1080 digital inputs < 5 ms 1920x1080 @ 60Hz Rise time + Fall time √...
  • Page 11 3.2.6 Support Timings Resolution Resolution Horizontal Vertical Nominal Pixel Mode (active dot) (total dot) Frequency (KHz) Frequency (Hz) Clock (MHz) 640x480@60Hz 800 x 525 31.469 59.941 25.175 640x480@72Hz 832 x 520 37.861 72.809 31.500 640x480@66.66Hz 864x525 66.66 30.24 VESA 720x400@70Hz 900x449 31.469 70.087...

  • Page 12: Operational & Functional Specification

    3.3 Operational & Functional Specification 3.3.1 Video performance *All spec. of monitor need to warm up at least 1hr. LGD LM230WF1-TLA3 Item Condition Spec OK N.A Remark Any input resolution modes √ Resolution which are under 1920x1080 1920x1080 Test Condition: Set Contrast at 50, Contrast ratio √...
  • Page 13 SEC LTM230HT01 Item Condition Spec OK N.A Remark Any input resolution modes √ Resolution which are under 1920x1080 1680x1050 Test Condition: Set Contrast at 50, Contrast ratio √ 600(min),1000(typ.) Brightness at 100, Color at User preset. Test Condition: Set Contrast at 50, At R/G/B saturated 300 cd/m (typ.),240 cd/m...
  • Page 14 3.3.5 Transportation Item Condition Spec OK N.A Remark Test Specification: 1. Frequency Hertz 5 ~ 250 HZ , PSD Level 0.0054 (G2/Hz) √ (1) Vibration Package, Non-Operating 2. Grms = 1.146 3. Sweep Time : 30 minutes per Axis 4. Axes : X,Y,Z Test Spectrum: 20 Hz 0.0185(g2/Hz) Unpackaged, Non-...

  • Page 15: Lcd Characteristics

    3.3.8 Reliability Item Condition Spec OK N.A Remark Excluding √ MTBF Prediction Refer to MIL-217F > 60,000 Hours CCFL √ CCFL Life time At 25±2℃, under 7.0mA 40,000 Hours (min) See Note-4 Note-4: CCFL lifetime is determined as the time at which brightness of lamp is 50%. The typical lifetime of CCFL is on the condition at 7.0mA lamp current.
  • Page 16 SEC LTM230HT01 Item Condition Spec OK N.A Remark √ LCD Panel Supplier √ Panel type of Supplier SEC LTM230HT01 √ Screen Diagonal 584.8mm(23”) √ Display area Unit=mm 509.76(H) x 286.74(V) √ Physical Size Unit=mm 534(H) x 311.7(V) x 18.9(D) √ Weight Unit=gram 3000 (typ.)
  • Page 17 3.4.2 Optical characteristics of LCD panel LGD LM230WF1 TLA3 Item Unit Conditions Min. Typ. Max. Remark [degree] Horizontal (Right) [degree] CR = 10 (Left) Viewing Angle [degree] Vertical [degree] (Up) CR = 10 (Down) Normal Direction Contrast ratio 1000 [msec] Rising Time Response Time [msec]...

  • Page 18: User Controls

    From 10 sec to 120 sec √ OSD Lock EMEA/Non-EMEA √ Language languages for Asia/Europe Version √ Recall Recall All √ Mode ACER Empower Mode D-sub √ Input Select HDMI Full √ Wide Mode Aspect √ Sharpness √ Display Information For input timing √...

  • Page 19: Mechanical Characteristics

    The detailed firmware functions’ specification, please refer to C212 S/W spec. document. 3.6 Mechanical Characteristics 3.6.1 Dimension Item Condition Spec OK N. Remark √ Bezel opening 511.46*288.39 mm Monitor without Stand 551.98*351.05*65.04 mm √ W x H x D mm Monitor with Stand √...

  • Page 20: Pallet & Shipment

    3.7 Pallet & Shipment 3.7.1 Container Specification Quantity of products Quantity of Products Quantity of pallet Stowing Type (sets) (sets) (sets) ontainer (Every container) (Every Pallet) (Every Container) Pallet A: 59 Pallet A: 10 Pallet B: Pallet B: With pallet 1080 Pallet A: 59 Pallet A: 20...

  • Page 21: Certification

    3.8 Certification Item Condition Spec OK N.A Remark ISO14000 √ API Doc. 715-C49 Green design Requirement √ Blue Angel German Standard √ E-2000 Switzerland Environment √ USA Standard √ TCO’99 √ TCO’03 √ MPR2 √ Green Mark √ Microsoft Windows PC98/99 √...

  • Page 22: Packing

    3.9 Packing - 22 -...

  • Page 23: Disassembly /Assembly

    Assembly Disassembly / 4.1 Exploded View - 23 -...
  • Page 24 - 24 -...

  • Page 25: Disassembly /Assembly

    4.2 Disassembly /Assembly 4.2.1 Assembly SOP Preparation before assemble 1.Clean the room for work 2.Identify the area for material 3.Prepare the implement, equipments, materials as bellow: 1) Press-fixture 2) working table 3) Screw-driver 4) knife*1 5) glove 6) cleaning cloth 7) ESD protection picture Operation...
  • Page 26 1.Assemble the power key to the BZL 2.Assemble the C/B BD and LED BD to the BZL Fix the LED BD with Screw-driver screws*2 Assemble the speakers to Screw-driver the BTK with screw*4 Assemble the wire to the I/F BD, the correct position reference on the picture Assemble the PCBA to...
  • Page 27 Lock 7 PCBA screws and one grounded screw on the PCBA board Fasten the LVDS to panel. Adhesive one yellow tape on the LVDS Assemble bracket module to BZL - 27 -...
  • Page 28 Stick aluminum foil to the panel and Bracket HDMI Tighten hexagon screw Screw-driver and one HDMI screw Assemble the L-SHD the correct position reference on the picture Insert lamp wire*4 to the Power board - 28 -...
  • Page 29 Insert control board cable to I/F housing Stick adhesive tape to fix up lamp wire Stick aluminum foil to the panel. Assemble the Rear Cover. - 29 -...
  • Page 30 Assemble the Hinge with Screw-driver screw*3 Lock 4 screws to RC. Screw-driver Cover the CLM of L and R - 30 -...
  • Page 31 4.2.2 Disassembly SOP Preparation before disassemble 1.Clean the room for disassemble 2.Identify the area for monitor 3.Check the position that the monitors be placed and the quantity of the monitor ;prepare the area for material flow; according to the actual condition plan the disassemble layout 4.Prepare the implement, equipments, materials as bellow: 1) Press-fixture 2) working table...
  • Page 32 Tear off aluminum foil Tear off adhesive tape unlock the hexangular Screw-driver screws and the HDMI HDMI screw Pull out light lamp 2 Wires Pull out one side of the control cable from SHD hole and tear off the adhesive tape. - 32 -...
  • Page 33 Tear off aluminum foil*3pcs Press the clip of the FFC, and Pull out FFC cable from panel Press the clip of the LVDS Unlock PCBA Screw and Grounding Screw Grounding Screw Pull out the cable from the connector - 33 -...
  • Page 34 Disassemble the speaker from the BKT Disassemble the I/F board - 34 -...

  • Page 35: Level 1 Cosmetic / Appearance / Alignment Service

    5. Level 1 Cosmetic / Appearance / Alignment Service 5.1 Alignment procedure (for function adjustment) 5.1.1 Preparation 1.) Setup input timing to any preset modes or patterns. 2.) Enter factory mode (press “e-Key” & “Power” buttons at the same time to turn on monitor). 3.) Move cursor into “Burn-in Mode”...
  • Page 36 Figure-1: Preset Timing modes list Resolution Resolution Horizontal Vertical Nominal Pixel Mode (active dot) (total dot) Frequency (KHz) Frequency (Hz) Clock (MHz) 640x480@60Hz 800 x 525 31.469 59.941 25.175 640x480@72Hz 832 x 520 37.861 72.809 31.500 640x480@66.66Hz 864x525 66.66 30.24 VESA 720x400@70Hz 900x449...
  • Page 37 5.1.3 ADC calibration (Auto color balance adjustment) ~~Analog only, it is not required for DVI-D input source 1. Setup input timing ICL-605( 1280x1024@75Hz ), pattern 42(5-Mosaic pattern with white color block) with Analog signals from Chroma video pattern generator. (it depends on Scaler IC supplier’s recommendation) 2.
  • Page 38 5.1.5. Writing EDID data into monitor 1. Setup a PC with DDC card. 2. Connect PC to monitor with a D-sub signal cable. 3. Please refer to the Q212 for the correct EDID file. 4. Runs the writing program to write the analog EDID data into EEPROM for analog input(ie. 15-pin D-sub).

  • Page 39: Software / Firmware Upgrade Process

    5.2 Software / Firmware Upgrade Process 5.2.1 Hardware prepared: Hardware Requirement: 1. ISP board x 1 VGA signal input from 15pin D-sub cable of PC or NB. Connect to target monitor Check the Jumpers on the ISP Circuit Board (make sure J5, J6, J7, J8 are set at ping 1,2 ) Connect ISP board and...
  • Page 40 5.2.2 Firmware Upgrade Procedure Step 1: Un-zip Port95nt and install into your computer. Step 2: Un-zip ISP application tool (RTDTool) Step 3: Press “RTD 2120 ISP” button to execute firmware program application. - 40 -...
  • Page 41 Step 4: Press “64K” button to load *series*.hex file and press “64~96” button to load *extend*.hex file from your compute Step 5: Select “Erase” option and execute lightning button first, and then select “Auto” option and execute lightning button to start upgrade firmware to the monitor. - 41 -...
  • Page 42 Note: you can change program speed bar to meet your equipment speed if program firmware fail. - 42 -...
  • Page 43 5.2.3 Turn Off Burn In IF the monitor without signal input has Burn In pattern. As the following figure ENTER and RIGHT to Burn In Off Press “MENU” and “>” key at the same time to exit Burn in mode(factory mode),and soft power key off/on restart the monitor.

  • Page 44: Edid Upgrade Procedure

    5.3 EDID Upgrade Procedure Step 1: Run the program “Q-EDID-V016.exe”, when the UI popped up Note: If “VGA” choose 128bytes, and “HDMI” choose 256bytes - 44 -...
  • Page 45 Step 2: Click “Open File” and select “VGA” or “HDMI” EDID file Step 3: If load file is successful, it shows “Open EDID Table OK..”. And then, Click “Write EDID” button to update EDID - 45 -...
  • Page 46 Step 4: If write EDID is successful, it shows ”Write EDID OK …” And then, click “Read EDID” button to check if successful or not. Step 5: If read EDID is successful, it shows” Read EDID OK …” - 46 -...

  • Page 47: Osd Operation Guide

    5.4 OSD Operation Guide - 47 -...
  • Page 48 - 48 -...
  • Page 49 - 49 -...
  • Page 50 - 50 -...
  • Page 51 - 51 -...
  • Page 52 - 52 -...

  • Page 53: Level 2 Circuit Board And Standard Parts Replacement

    6. Level 2 Circuit Board and Standard Parts Replacement 6.1 Trouble Shooting Guide 6.1.1 No Display or display is unstable (Interface Board) No picture or picture unstable Turn on power Power off Check all of wires then turn Does cable plugs in connector ? on power switch again Does power stable ? Check Power BD...
  • Page 54 6.1.2 Check Control Board OSD is not working Plug control BD Is control BD connecting? then retry Is bottom switch normally ? Replace control BD then retry Replace Control BD Is OSD working ? Check Interface BD - 54 -...
  • Page 55 6.1.3 OSD Function OSD doesn’t work Is control BD working ? Replace control BD Check interface BD - 55 -...
  • Page 56 6.1.4 Power no work trouble shooting - 56 -...

  • Page 57: Circuit Operation Theory

    6.2 Circuit Operation Theory I. Introduction H233H is a 23 inch and 24bits color TFT LCD monitor, which can support the resolution up to 1920x1080. It has VGA, DVI and HDMI input and compliant with VESA specification to offer a smart power management.
  • Page 58 III. Circuit Implementations: A.) THE MAIN BODY: A-1.) Interface board block diagram : (a) Circuit operations: The scaling IC has OSD and auto detecting input timing functions. OSD offers adjustable functions to the end-users. Auto detecting timing function can detect change modes. It outputs the digital R-G-B data, pixel clock and control signal to TCON of the LCD module.
  • Page 59 output section contains a 24-bit TTL output interface and a channel LVDS transmitter for direct interfacing of commercially available LVDS LCD panel modules. In addition, RTD2525LH embedded 16.5KSRAM dynamically stores OSD command and fonts, compatible advanced color control features. 2.) EEPROM: We use 24C16 EEPROM to store monitor user data and user preset timings.
  • Page 60 #1 EMI Filter This circuit (fig. 2) is designed to inhibit electrical and magnetic interference for meeting FCC, VDE, VCCI standard requirements. Fig. 2 - 60 -...

  • Page 61: Spare Parts List

    CATEGORY DESCRIPTION ACER PART NO. LCDM23W LM230WF1- LK.23008.003 TLA3 LGD Board BOARD PCBA IF BD H+S LGD 55.LHB0Q.001 MI H233H BOARD PCBA SPS BD HDMI 19.LHB0Q.001 LGD MI H233H BOARD PCBA CTRL BD HDMI 55.LHB0Q.002 MI H233H - 61 -...
  • Page 62 BOARD PCBA LED BD MI 55.LHB0Q.003 H223HQ BOARD PCBA JACK BD AU MI 55.LF70Q.002 H223HQ Cable CABLE CORD VCTF7A125V 27.LE20Q.001 1.8M JAN DELL CABLE CABLE DVI-D/DVI-D 50.LBJ0Q.001 1.8M IS_8 VW - 62 -...
  • Page 63 CABLE FFC LVDS 30/30P T/B 50.LGQ0Q.002 LOCK CABLE FFC CABLE 5P LED BD 50.LF70Q.002 H223HQ CABLE WIRE 8/4P 1571#28 50.LF70Q.005 AUDIO-BD CABLE WIRE 9/11-P #24 50.LGQ0Q.005 115MM V233H CABLE FFC WIRE 7P CTRL BD 50.LHB0Q.001 H233H - 63 -...
  • Page 64 CABLE CABLE SIGNAL/C H+V 50.LBJ0Q.002 OD_5.5 1.8M Assembly CASE/COVER/BRACKET ASSY PWRBTN DT05A 60.LF70Q.009 ASSEMBLY H233H/223HQ CASE/COVER/BRACKET ASSY BZL LG HDMI 60.LHB0Q.001 ASSEMBLY DT02A H233H CASE/COVER/BRACKET ASSY RC LG 1A1D1H- 60.LHB0Q.002 ASSEMBLY A H233H - 64 -...
  • Page 65 CASE/COVER/BRACKET ASSY BASE-S WP 60.LF70Q.007 ASSEMBLY DUAL H223HQ CASE/COVER/BRACKET ASSY CLMN ABS+P 60.LF70Q.003 ASSEMBLY DT03A H223HQ - 65 -...

  • Page 66: Appendix 1 - Screw List / Torque

    Appendix 1 – Screw List / Torque (A) STANDARD SCREW TORQUE SPEC. MOUNTING TORQUE HOLE SIZE Screw ITEM DESCRIPTION MATERIAL (Kgf-CM) (MM) Head 8F.205B4.019 SCRW MACH HEX #4-40*0.3" NI METAL 5.0±0.6 #4-40 8F.5A224.6R0 SCRW MACH FLAT M3*6L ZN METAL Side mount:3±0.6 M3*0.5 Other: 4±0.6 8F.XA356.6R0 SCRW TAP FLAT M4*6L B-ZN...
  • Page 67 8F.WA324.6R0 SCRW TAP CAP M3*6L B-ZN PLASTIC 4.0±1.0 Φ2.35±0.05 8F.LA222.4R0 SCRW TAP PLASTIC 1.5±0.05 Φ1.65±0.05 FPHM2*4L(3.5/0.5)ZN 8F.1A524.5R0 SCRW MACH PAN M3x5L NI METAL 3.5±0.3 Φ2.68±0.03 8F.00518.100 SCRW TAP W/FL M3*10L(S3.8) METAL None tread ： 8 ～ Φ2.68±0.03 Have tread:3±0.6 Aluminum:4~5 8F.XA324.5R0 SCRW TAP FH M3*4.5L B-ZB PLASTIC 5.0±1.0...

  • Page 68: Appendix 2 - Physical Dimension Front View And Side View

    Appendix 2 – Physical Dimension Front View and Side view Fig. 1 Physical Dimension Front View and Side view - 68 -...
  • Page 69 Fig. 2 Appearance Description - 69 -...

  • Page 70: Appendix 3 - Interface Board

    Appendix 3 – Interface Board - 70 -...
  • Page 71 - 71 -...
  • Page 72 - 72 -...
  • Page 73 - 73 -...
  • Page 74 - 74 -...

Table of Contents