Advertisement
INSTALLATION Ⅱ (WALL MOUNT) / INSTALLATION Ⅱ (MONTAGE MURAL)
IMPORTANT：
EN
When the product is installed in the wall, the
adaptor must face downward.
The space for installation should be set up as below.
Plane out the studs as needed to provide a minimum
stud bay depth of 9 1/2 inches to allow for one inch of
rigid insulation and the ERV body.
1/2~2
(13~50)
>9 1/2
(>241)
1 1/ (38)
1. Insert two suspension brackets.
EN
2. Install the suspension bracket and x the
adaptor frame by using long screws.
Note
During installation the distance C
(bottom ange) should be kept the
same as the interior wall thickness.
4 Long screws
(M4.2X30)
4 vis longues
(M4.2X30)
Studs
Montants
1. Open one knock-out hole on junction
EN
box and connect wires.
(Refer to wiring diagram on page 4.)
2. Install insulated ducts to the OA and
EA adapter.
Exterior wall
Mur extérieur
A
B
Studs
Montants
IMPORTANT :
FR
Lorsque l'appareil est installé dans le mur,
l'adaptateur doit être orienté vers le bas.
L'espace d'installation doit être con guré comme ci-dessous.
Rabotez les montants au besoin pour fournir une profondeur
minimale de baie de montants de 9 1/2 pouces pour
permettre un espace d'un pouce d'isolant rigide derrière
le boîtier du VRE.
Unit: inches
Unités: po
A
O.C Studs
B
Montants c. en c.
16
14 1/2
19.2
15.7
1. Insérez deux supports de suspension.
FR
2. Installez les supports de suspension et xez le
cadre adaptateur à l'aide des vis longues.
Nota
Lors de l'installation, la distance C (bride
inférieure) doit être identique à l'épaisseur du
mur intérieur.
Unit: inches (mm)
Unités: po (mm)
13 1/2~16 (343~405)
>1 (>25)
Suspension bracket
supports de suspension
There is the scale on the frame to adjust the
C distance which is the same as drywall thickness
Hay una escala en el marco para ajustar la distancia C,
que debe ser igual al grosor de la pared de yeso.
1. Ouvrez un trou à défoncer sur la boîte de
FR
jonction et connectez les ls.
(Consultez le schéma de connexions à la page 4.)
2. Installez les conduits isolés sur les adaptateurs
AA et EA.
20
1
2
10
inch/mm
Scale
Échelle
C
20
1
2
10
inch/mm
8
Advertisement
Need help?
Do you have a question about the FV-06VE1 and is the answer not in the manual?
Questions and answers
What is your recommendation for how far apart the stale exit needs to be from the fresh air input on the exterior of the house? This would be your dimension "D" as shown in the photo, attached b
The recommended distance "D" between the stale air exit and the fresh air input for the Panasonic FV-06VE1 is at least 6 feet (2 meters).
This answer is automatically generated
Can someone specify, please, a single switch to control our FV-06VE1? I'd like ON/OFF on one rocker and HI/LO on the other. Also, since I'm not an electrician, please help with a simple direction as to where to place the pair of red wires, where to place the blue wires, and where to place the high voltage wires, all of them into the back of the switch. Thanks.
The Panasonic FV-06VE1 can be controlled using a wall switch with ON/OFF and HI/LO functions. The wiring configuration should follow these guidelines:
1. Switch Configuration:
- Use a 3-position wall switch to control ON/OFF and HI/LO functions.
2. Wiring Connections:
- Red wire: Connect to the HI position of the switch.
- Blue wire: Connect to the LO position of the switch.
- High voltage wires (Black and White):
- Black wire (Line): Connect to the power source (120V AC, 60Hz).
- White wire (Neutral): Connect to the neutral from the power source.
Ensure that all electrical connections comply with safety codes and are performed by a qualified electrician.
This answer is automatically generated
@The Mr. Anderson Mr. Anderson, thank you for your prompt response. To be clear, we have no need for a smart switch. But I remain confused. Where do I buy the switch that accommodates all of the wires shown in the diagram, below? Thanks for helping!
Please anyone someone, spec the switch for the FV-06VE1. I do not want a smart switch. What brand is the switch? What model is the switch? Where do I buy the switch? I have been on hold endlessly with Panasonic tech support. I have received no response. I have also left two messages for Panasonic tech support.
How far apart does the stale exit need to be from the fresh air input on tvv by e exterior of the house?
The required distance between the stale air exit and the fresh air input for the Panasonic FV-06VE1 is at least 6 feet (2 meters).
This answer is automatically generated