Sencore ReZolver LC103 Operation And Application Manual page 25

Aluminum Electrolytics
Capacit~
1.5V 3.0V 6.0V
10V 15V 20V 25V 35V 50V 100V 200V 300V 400V
500V
600V 1000V
<1.0 1.0
1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 3.5 4.9 6.1 7.0
7.8 8.6 11
1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 3.5
4.9 6.1 7.0 7.8 8.6 11
1.5 1.0 1.0 1.0 1.0 1.0 1.0 1.4 1.0 2.0 4.3
6.1 7.4 8.6 9.6 11 14
2.2
1.0
1.0 1.0 1.0 1.0 1.0 1.8 1.2 2.0 5.2 7.3 9.0 10
12 13 16
3.3
1.0
1.0
1.0
1.0 1.0 1.5 2.2 2.0 3.0 6.4 9.0 11 13 14 16
20
4.7 1.0 1.0 1.0 1.0 1.5 2.0 2.6 2.5 3.5
7.6 11 13 15 17 19 24
6.8 1.0 1.0
1.0 1.5 2.0 2.5 3.0 3.0 6.5 9.1 13 16 18 20 22
29
10 1.6
1.6 1.6 2.0 2.5 3.0 4.0 5.0 7.8 11 16 19 22 25 27 35
15
2.2 2.2 2.2 2.5 3.0 4.0 7.0 5.0 9.6 14 19 23 27 30 33
43
22
2.8
2.8
2.8 3.0
5.0
9.5
10 10 12 16 23 28 33 37 40 52
33 3.4 3.4
3.4 5.0
7.5 15
10
11 14 20 28 35 40 45 49 64
47
4.0 4.0
4.0 10 10 15 15 16 17 24 34 42 48 54 59 76
68
5.0
5.0
5.0 15
15
20
15 17 20 29 41 50 58 65 71 91
100 10 10
10 15 20 20 17 21 25 35 49 61 70 78 86 111
150
15
15 15 20 20 19 21 25 30 43 61 74 86 96 105 136
220 20 20 20 20 20 23 26 31 37 52 73 90 104 116 127 164
330 20 20
20 20 25 28 32 38 45 64 90 110 127 142 156 201
470 24 24 24 24 29 34 38 45 54 76 107 131 152 170 186
240
680
29 29 29
29
35
41 46 54
65
91 129 158 183 204 224 289
1000
35 35
35 35
43 49
55 65
78 111 157 192 221 247 271 350
1500
43
43
43 43
53
61 68
80 96
136 192 235 271
303
332 429
2200
52
52 52 52 64 73 82 97 116 164 232 284 328 367 402 519
3300
64 64 64 64 78 90 101 119 142 201 284 348 402 450 492 636
4700 76 76 76 76 93 107 120 142 170 240 339 416 480 537 588 759
6800 91 91 91 91 112 129 144 171 204 289 408 500 577 645 707 913
10000 111 111 111 111 136 157 175 207 247 350 495 606 700 783 857 1107
15000 136 136 136 136 166 192 214 254 303 429 606 742 857 959 1050 1356
22000 164 164 164 164 201 232 260 307 367 519 734 899 1038 1161 1272 1642
33000 201 201 201 201 246 284 318 376 450 636 899 1101 1272 1422 1557
2011
47000 240 240 240 240 294 339 379
449 537 759 1073 1314 1518 1697 1859 2399
68000
289 289 289 289 353
408 456 540 645 913 1291 1581 1825 2041 2236 2886
100000 350 350 350 350 429 495 553 655 783 1107 1565 1917 2214 2475 2711 3500
150000 429 429 429 429 535 606 678 802 959 1356 1917 2348 2711 3031 3320 4287
200000 495 495 495 495 606
734
783 971 1100 1570 2210 2710 3130 3500 3830
5191
Table 4 - Maximum allowable leakage for aluminum electrolytics per EIA standards.
Leakage charts
The fo llowing leakage charts list the maximum amount of
al lowable le akag e for the most common aluminum
e lectrolytics and dipped solid tantalum capacitors. These
charts a re duplicated on th e PULL CHART below th e
LC103. Good capacitors (as far as leakage is concerned) will
measure lower than the amou nts shown in the Leakage
Charts. v\Then m easuring leakage, you do not need to wait
for the readings to drop to zero or to its lowest point The
capacitor is good for any leakage reading which is lower than
the amount shown in the chart.
Leakage values shown in Table 4 for alumin um electrolytic
capacitors are the worst-case conditions, as specified by the
22
Electronic Industries Association (EIA) standard RS-395. The
values are determined by the formulas: L
=
0.05 x CV (for CV
products less than 1000) or L
=
6 x square root of CV (for CV
products greater than 1000. (The CV product is equal to the
capacitance value multiplied by the voltage rating).
T he tantalum capacitor leakage values listed in Table 5 are
fo r the most common type of tantalu m capacitors - dipped
solid, type 3.3. These values are specified by EIA standard
RS-228B, following the formula: L
=
0.35 x square root of
CV. In a few app lications outside of consumer service,
tantalum capac itors other than type 3.3 may be
encountered. Refer to the manufacturers specifications for
the m aximum allowable leakage for th ese special capacitor
types.