Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Qcells Q.TRON(BLK) M-G2.X Series
Summary of Contents for Qcells Q.TRON(BLK) M-G2.X Series
- Page 1 Installation and operation manual Q.TRON(BLK) M-G2.X solar module series...
-
Page 2: Table Of Contents
Table of contents 1 Introduction 2 Planning 2.1 Technical specifications 2.2 Requirements 2.3 Mounting options 2.4 Electrical layout 3 Installation 3.1 Safety and transport 3.2 Preparation of installation 3.3 Module installation 4 Electrical connection 4.1 Safety 4.2 Electrical installation safety 4.3 Connection of modules 4.4 After installation 5 Grounding 6 Faults and defects 7 Disposal 8 Maintenance and cleaning DOCUMENT REVISION 02 This Manual is valid for Africa, Asia, Europe, Latin America and South America as of July 1st 2023 for Q.TRON (BLK) M-G2.X solar modules, and replaces all earlier versions. -
Page 3: Introduction
1 Introduction With solar modules from Hanwha Q CELLS GmbH (hereafter Beware of possible danger or damage. referred to as "Qcells") you can directly transform the sun’s Categories: limitless energy into environmentally-friendly solar electricity. Danger: Risk of fatal injury ■ In order to ensure the maximum performance of your Qcells Attention: Risk of serious injury or damage to ■... - Page 4 Qcells assumes no liability on the basis of these instructions. Qcells is only liable in the context of contractual agreements or in the context of accepted guarantees. Qcells accepts no other responsibility for the functionality and safety of the modules.
-
Page 5: Planning
2 Planning 2.1 Technical specifications For additional information see the relevant datasheet of the module provided at www.qcells.com. Q.TRON M-G2+ Q.TRON BLK M-G2+ PRODUCT LINE Q.TRON M-G2.4+ Q.TRON BLK M-G2.4+ Type Q.ANTUM NEO Length 1722 mm Width 1134 mm Frame height 30 mm Area 1.953 m²... -
Page 6: Requirements
Do not bring any chemical substance (e.g. oil, solvent etc.) into ■ mounting frame. contact with any part of the panel. Only substances, which are released by Qcells, are allowed to be used during installation, Module Orientation Requirements operation and maintenance. Vertical or horizontal installation is permitted. -
Page 7: Mounting Options
2 Planning 2.3 Mounting options REQUIREMENTS OF ALL MOUNTING OPTIONS The loads in the table are related to the mechanical stability of the solar modules. The mechanical stability of the mounting system including clamps has to be evaluated by the system supplier. The listed test load values have been determined with the following clamp parameters: clamp width = 40 mm and clamp depth = 10 mm. - Page 8 2 Planning 2.3 Mounting options 4 CLAMPS ON SHORT SIDE & 4 CLAMPS ON SHORT SIDE 2 CONTINUOUS RAILS PARALLEL TO LONG SIDE CL2a CL2b CL2a CL2b CL2a CL2b POSITION OF TEST LOAD DESIGN LOAD POSITION OF TEST LOAD DESIGN LOAD CLAMPS* [mm] PUSH / PULL [Pa] PUSH / PULL [Pa] CLAMPS* [mm]...
- Page 9 2 Planning 2.3 Mounting options 6 CLAMPS ON LONG SIDE & 6 CLAMPS ON LONG SIDE (SHORT RAILS ALLOWED) 3 CONTINUOUS RAILS PARALLEL TO SHORT SIDE CL6a CL6c 20 - 250 560 - 1160 CL6a CL6b CL6c CL6d POSITION OF TEST LOAD DESIGN LOAD POSITION OF TEST LOAD...
- Page 10 2 Planning 2.3 Mounting options Mounting options with bolts The illustrated installation options apply for both horizontal and vertical module orientation. Module Bolt Mounting rail 4 BOLTS / SCREWS ON LONG SIDE & 4 BOLTS / SCREWS ON LONG SIDE & 2 CONTINUOUS RAILS PARALLEL TO SHORT SIDE 2 CONTINUOUS RAILS UNDERNEATH LONG FRAME PARTS POSITION OF TEST LOAD...
-
Page 11: Electrical Layout
For detailed key electrical data, please refer to the actual data Modules may be damaged by the occurrence of reverse currents sheet referring to the relevant Module (available at www.qcells. (caused by module defects, ground leaks, or defective insulation). com). -
Page 12: Installation
3 Installation 3.1 Safety and transport Ensure that all personnel are aware of and adhere to Danger! Risk of fatal injury due to electric shock! accident-prevention and safety regulations. Do not install damaged modules. While working wear clean gloves. Inform your distributor of any damages immediately. §... - Page 13 Note! Module damage may occur! Note! Module damage may occur! Do not drop modules. Only make modifications to the module which have been confirmed in writing by Qcells. confirmation letter Note! Module damage may occur! Note! Module damage may occur! Do not stack modules.
-
Page 14: Preparation Of Installation
3 Installation 3.2 Preparation of installation Danger! Risk of fatal injury due to electric shock! Warning! Risk of injury due to falling modules! Block off the installation zone. Secure modules during installation. Keep children and unauthorized individuals away Do not install modules in windy or wet weather. from the solar power system. -
Page 15: Module Installation
3 Installation 3.3 Module installation Option 1: Maintain an interval of at least 10 mm between two modules along the short side and 5 mm along the Fasten the module with 4 clamps in the specified long side. clamping range, see section "Mounting options with clamps"... -
Page 16: Electrical Connection
4 Electrical connection 4.1 Safety Danger! Danger! Risk of fatal injury due to electric shock! Risk of fatal injury due to electric shock! Never open the junction box. Do not remove bypass diodes. When disconnecting an electric circuit carrying direct current, electric arcs can occur that may result in life-threatening injuries. Do NOT unplug the cable when under load. -
Page 17: Electrical Installation Safety
4 Electrical connection 4.2 Electrical installation safety Danger! Risk of fatal injury due to electric shock! Danger! Risk of fatal injury due to electric shock! Electrical work may only be performed by qualified Never plug or unplug the cable when under load. and skilled personnel (see page 3). -
Page 18: Connection Of Modules
4 Electrical connection 4.3 Connection of modules Use solar cables for the connection at the junction Note! Module damage may occur! box outlet. Ensure that the cabling is not under mechanical stress Only interconnect connectors of the same type and (Comply with bending radius of ≥ 60 mm). manufacturer. -
Page 19: After Installation
4 Electrical connection 4.4 After installation Ensure that all necessary safety and functional tests Note! Module damage may occur! have been carried out according to applicable Ensure that the plug connections are secured away standards. from any water-channelling surface. Integrate the system into the existing lightening Warning! Fire Risk! protection system in accordance with the applicable Do not use light concentrators (e.g. -
Page 20: Grounding
Risk of fatal injury due to electric shock! statutory regulations. Do not attempt to fix any problems yourself (e.g., glass cracks, damaged cables). Please contact an installer or Qcells Technical Customer Service Department. 7 Disposal Do not disconnect modules by yourself. -
Page 21: Maintenance And Cleaning
8 Maintenance and cleaning NOTE! Qcells solar modules are known for a long operating life and minimal maintenance effort and expense. Dirt and grime are Dust and dirt are abrasive materials! usually washed away by rain. If the module is fully or partially shaded by dirt or debris (e.g., plants, bird droppings), it needs... - Page 22 Hanwha Q CELLS GmbH EMAIL sales@qcells.com +49 (0)3494 66 99 – 23222 www.qcells.com +49 (0)3494 66 99 – 23000 OT Thalheim, Sonnenallee 17-21, 06766 Bitterfeld-Wolfen, Germany Subject to change without notice. © Qcells Installation manual solar modules Q.TRON_M-G2.X_modules_series_2023-07_Rev02_EN...
Need help?
Do you have a question about the Q.TRON(BLK) M-G2.X Series and is the answer not in the manual?
Questions and answers