Table of Contents
Advertisement
Quick Links
Edel AIR
Domestic hot water heat pump
100 and 150 litres wall mounted
Air intake and exhaust using a Ø80/125 concentric duct
Installation manual
Manual ref. : 1898153
Edition n° 22.47
The information contained in this document is non-contractual. Auer reserves the right to modify the technical specifi cations or characteristics of any of their appliances without prior notice.
Edel 100 AIR
Ref. 353210
Edel 150 AIR
Ref. 353211
Made in France
Advertisement
Table of Contents
Troubleshooting
Subscribe to Our Youtube Channel
Related Manuals for auer Edel 100 AIR
Summary of Contents for auer Edel 100 AIR
- Page 1 Ref. 353211 Made in France Manual ref. : 1898153 Edition n° 22.47 The information contained in this document is non-contractual. Auer reserves the right to modify the technical specifi cations or characteristics of any of their appliances without prior notice.
-
Page 2: Table Of Contents
TABLE OF CONTENTS 4.2.3- Piping accessories ....................19 1-SAFETY ............. 4 4.2.3.1 - For air duct connection onto ambient or exterior air ....19 2 - RECOMMENDATIONS ........7 4.2.3.2 - For connection with a Ø80 PVC pipe ..........19 2.1 - Storage ....................7 4.2.3.3 - Essential accessories for air duct connection 2.2 - Transport ....................7 or air exhaust connection using a Ø80 PVC pipe .......19... - Page 3 6 - MAINTENANCE AND TROUBLESHOOTING 28 6.1 - Water circuit / Condensates drainage ........28 6.2 - Air intake circuit..................29 6.3 - Electrical maintenance ..............29 6.4 - Inspecting the corrosion-proof anode Changing the primary anode of the heating element or cleaning the tank ................29 6.5 - Modifi cation..................30 6.6 - Decommissioning ................30 6.6.1- Interim Decommissioning of Product ..............30...
-
Page 4: 1-Safety
Preserving these documents • Follow all relevant national and international health and safety rules and regulations. This manual and all other relevant documents should be given to the system user. Danger resulting from improper use The system usre should keep these manuals for future reference. Any work carried out by an unqualifi ed person can result in damage to the installation or in 1-SAFETY... - Page 5 Protect the appliance with: - Maintenance - Troubleshooting - • A 6A all-pole circuit breaker with a • Drainage: Turn off the power supply and the contact opening of at least 3mm. cold water supply, open the hot water valves •...
- Page 6 HEAT PUMP WATER HEATER 100L & 150L AIR INSTALLATION MANUAL...
-
Page 7: Recommendations
2 - RECOMMENDATIONS • The appliance can only function when fi lled with water. Never turn on the appliance if the tank has not been properly fi lled with water and completely purged of air. • The corrosion-proof magnesium anode Transporting the appliance in a horizontal ensures the protection of the tank. -
Page 8: Introduction
3 - INTRODUCTION 3.1 - Dimensions HEAT PUMP WATER HEATER 100L & 150L AIR INSTALLATION MANUAL... -
Page 9: Technical Characteristics And Performances
3.2 - Technical characteristics and 3.3 - EU declaration Performances This device complies with international electrical safety standards IEC 60335-1, IEC 60335-2-21, IEC 60335-2-40. The CE marking present on the device attests to its conformity with the Domestic hot water heat pump model 100L AIR 150L AIR following Community Directives, of which it meets the essential... -
Page 10: Installation
4 - INSTALLATION 4.1.3 - On-ground installation A tripod, see § «Options», allows to install the Heat pump water heater on the ground, in the case 4.1- Set-up where the wall will not support the weight of the water heater. 4.1.1- Installation site The height of the tripod is adjustable from 300mm to 500mm. -
Page 11: Options
Ø132mm drilling axes for the concentric duct Drilling template provided with the heat pump water heater 100L The vertical positioning of the heat pump water heater must be strictly respected. If it is not, condensates could overfl ow and water may leak out onto the fl oor. -
Page 12: 1- Air Intake And Exhaust In Unheated Premises (10M² Minimum)
4.2.1.2- Exterior air exhaust using Ø80 PVC 4.2.1- Air intake and exhaust in unheated pipe premises (10m² minimum) insulated from neighbouring heated rooms A < 10m (1 extra elbow equivalent to 1m) If insulation of heated adjoining rooms is insuffi cient, loss of heat is more likely. 4.2.1.1 - In the same room as the appliance Description Rep. -
Page 13: In An Adjoining Room, With Vertical Air Ducts
4.2.1.4 - In an adjoining room, with vertical air ducts Min. cutting height for the Ø125 X + D < 5m insulated elbow (rep.a1)= 220mm • Height of dimension «D»: - if D = 350mm, use the insulated Ø80/125 air duct elbow rep.a1 ) without cutting it again. -
Page 14: Installing With Lateral Air Ducts
rep.f X + 25 mm • Cut the Ø125 PVC pipe ( ) to ( Rep. Description • Glue the pipe into the air duct nozzle. Rear or vertical insulated air duct Ø80/125 - 355mm long • Position the Ø125 wall joint. (air duct nozzle + Ø125 wall joint + F155/F125 wall flange + •... -
Page 15: Installing With Lateral Air Ducts
rep.f • Cut the Ø125 PVC pipe ( ) to (X + 25mm). Rep. Description • Glue it into the air duct nozzle. Rear or vertical insulated air duct Ø80/125 - 355mm • Position the Ø125 wall joint. long • Pass the assembled air duct nozzle through the wall from the outside. (air duct nozzle + Ø125 wall joint + F155/F125 wall •... -
Page 16: Installation With Lateral Air Ducts And Elbow Outlet
- Remove the cover parts from the fi rst insulated elbow 4.2.2.4 - Installation with lateral air ducts and - Insert the fi rst Ø80 PVC elbow into the base of the fi rst insulated elbow outlet elbow and fi x it to the Ø80 PVC pipe (apply a bit of silicone so that A + B + X <... -
Page 17: Installation With Lateral Ducts At Distance "C
• FOR PART «C»: 4.2.2.5 - Installation with lateral ducts at - Remove the Ø80 PVC pipe (lg 140mm) located on the appliance’s distance «C» above the appliance air outlet. rep.e - Cut the second Ø80 PVC pipe ( ) to (C-65mm) A <... - Page 18 • Position the Ø125 PVC pipe through the ceiling and insulation, as well as the two F155/F125 fl ange rings, one placed on the inside and one on the outside. Do not glue the two F155/F125 fl ange rings onto the Ø125 PVC pipe. •...
-
Page 19: 3- Piping Accessories
4.2.3- Piping accessories 4.2.3.1 - For air duct connection onto ambient or exterior air Ø80/125 Insulated elbow kit for air duct includes: Ø125 insulated elbow + parts for insulated elbow + Ø80 F/F PVC elbow Ø80/125 Insulated elbow kit for air duct includes: Ø125 insulated elbow + parts for insulated elbow + Ø80 F/F PVC elbow PVC e... -
Page 20: Condensates Drainage
• It is advised to fi t a shut-off valve above the pressure-relief valve. It is strongly advised to NOT use a • For installations equipped with: recirculation pump. This appliance is - small diameter piping not intended for connection to a recirculating - ceramic plate valves pump. -
Page 21: Electrical Connections
• Remove the protective casing. 4.5 - Electrical connections • Remove the black cover from the electronics board. • Pass a 0.75mm² 2-wire cable with metal tips through a cable gland at the back of the appliance and bring the end of the cable around Do not connect the Heat pump water to the electronics board. -
Page 22: Connection To The Pv Function
4.5.1.4 - Connection to the PV function This function enables the appliance to operate in auto- production mode, which means that it will use the energy produced by the PV function to supply the heat pump as well as the electrical back-up, and to heat the water in the tank. -
Page 23: Setting The Language
5.2 - Setting the language 5.4 - Setting the desired water temperature When the appliance is turned on for the fi rst time, the language must 5.4.1 - PV mode not activated be selected. Turn the dial to the left and select «English». Confi rm your selection by pressing on the dial. -
Page 24: Holiday/ Temporary Standby Mode
5.5 - Holiday/ temporary standby mode 5.6 - BOOST mode (for occasional use and for guaranteed comfort) h o l i d a y « » mode puts the appliance on standby while frost protection mode remains active. This function can be programmed boost The «... -
Page 25: Installer Menu
7. Turn the dial to select the primary function: 5.9 - INSTALLER menu - Menu → INST. MENU → PV MODE → PRIORITY It may be necessary to adjust certain settings to optimise the • Yes: the signals from connectors 1 and 2 take precedence over eco and frost protection modes. -
Page 26: Fan Mode -Fan Mode
• If the desired water temperature is set at 60°C, (see § «Setting the If the load shedding switch is on: desired water temperature»), there will not be an anti-legionellosis Mode 0 = No element is authorised to operate. cycle as it is already running continuously. •... -
Page 27: Resetting Parameters
AUTO = Lock menu access with temporary unlocking (60 seconds), 5.9.5 - Reading data press for 3 seconds. The «READ DATA» menu shows you, in real time, the information given by the sensors. Go to the «Installer» menu, turn the dial to «display». unlock Display Description... -
Page 28: Maintenance And Troubleshooting
6 - MAINTENANCE AND .../... →The TROUBLESHOOTING refrigerant circuit containing fl ammable refrigerant complies with all national gas regulations. In order to maintain effi ciency and improve durability → In case of maintenance of the refrigerant circuit: it is advised that an annual maintenance check should be carried out by a qualifi ed professional. -
Page 29: Air Intake Circuit
• To change the primary anode, unscrew the self-locking nut and 6.2 - Air intake circuit washer, and remove the primary anode with its seal. • Fit the new anode into place with a new seal, and tighten the self- The only maintenance work needed on the air intake circuit is to locking nut and washer. -
Page 30: Modifi Cation
6.5 - Modifi cation • The heat limiting safety thermostat for electrical back-up is activated Any modifi cation of the device is prohibited. Any replacement of Before resetting, check that: components must be done by a professional with original parts •... -
Page 31: List Of Spare Parts
6.11 - List of spare parts 100L 150L Description Regulation / Display B1244096 B1244096 Electronic circuit board controller Circuit board + display +H2P program - CET B4992816 B4992816 B4992653 B4992653 Display screen cable - 480mm + foam B1244576 B1244576 Temperature sensor lg460mm B1244577 Temperature sensor lg700mm B1244575... -
Page 32: Error Message Codes : Errors, Solutions
6.12 - Error message codes : errors, solutions, and operating in case of error Note: Errors can be dismissed by briefl y pressing the dial (manual reset) Temporary operation measures Display Error Probable causes Solutions while waiting for the problem to be solved •Voltage too high on electrical network... - Page 33 Temporary operation measures Display Error Probable causes Solutions while waiting for problem to be solved •The air and defrosting sensors are reversed on the circuit board •The defrosting and water sensors are reversed on the circuit board •Reposition the temperature •Incorrect temperature sensor sensors correctly on the main reading...
-
Page 34: Warranty
7 - WARRANTY 7.1.2.2 - Handling Cases (not limited to) where the warranty is void: • Any damage sustained by impacts or falls during handling after The tank is guaranteed against breakage for a period of five (5) delivery from the factory. years, starting from the date the appliance was activated, if •... -
Page 35: Appendices
8 - APPENDICES 8.1 - Electrical wiring diagram HEAT PUMP WATER HEATER 100L & 150L AIR INSTALLATION MANUAL... - Page 36 • Wait for the fan to come to a complete stop before undertaking any work on the appliance. Spare parts department Industrial and development Tel. : 03 22 61 21 21 - Fax : 03 22 61 33 35 E-mail : pieces@auer.fr site Rue de la République Technical department E-mail : enr@auer.fr...
Need help?
Do you have a question about the Edel 100 AIR and is the answer not in the manual?
Questions and answers