Sealey VS2080 Quick Start Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear a face
instruction shield
manual
1. SAFETY
WARNING! Ensure Health and Safety, local authority and general workshop practice regulations are adhered to when using tools.
‰
WARNING! Always use caution when working around fuel systems. The fuel in the fuel rail may be pressurised even if the engine is
‰
not running.
IMPORTANT: These instructions are provided as a guide only. Always refer to the vehicle manufacturer's service instructions, or a
proprietary manual, to establish the current procedure and data, also any warnings or cautions particular to the vehicle.
DO NOT use the set if any parts are missing or damaged.
8
DO NOT use this tool for any purpose other than that for which it is designed.
8
Switch off vehicle's ignition and disconnect the battery before commencing work under the bonnet.
9
You must follow the vehicle's service manual cautions when working around the air bag system. If the cautions are not followed the air
9
bag may deploy unexpectedly even after the ignition is turned 'OFF', resulting in personal injury.
Never lay tools on the vehicle's battery. This may short the terminals together, causing harm to yourself, the tools, or the battery.
9
Operate in a well ventilated area. DO NOT inhale fuel vapours.
9
Wear approved eye protection. A full range of personal safety equipment is available from your Sealey stockist.
9
Wear suitable clothing to avoid snagging. DO NOT wear jewellery and tie back long hair.
9
Keep children and other unauthorised persons away from the working area.
9
Keep yourself, tools, and test equipment away from hot engine parts.
9
Always keep a fire extinguisher that is suitable for fuel/electrical/chemical fires close by,
9
WARNING! NEVER smoke or have open flames near vehicle.
‰
Always relieve fuel pressure before disconnecting fuel lines from injectors.
9
Use a cloth to cover fuel line fittings when connecting or disconnecting fuel lines. Avoid contact with fuel.
9
Clean up all fuel spills immediately and dispose of all used cloths properly.
9
Maintain the tool components in good and clean condition for best and safest performance.
9
When work on the vehicle is finished, ensure all connections on vehicle are restored, and that there are no tools left in the engine bay.
9
Replace tools in the carrying case and store in a safe, dry, childproof location.
9
Air under pressure can cause severe injury.
9
Always shut off air supply, drain hose of air pressure and disconnect tool from air supply when not in use, before changing accessories
9
or when making repairs.
Never direct air at yourself or anyone else.
9
Whipping hoses can cause severe injury. Always check for damaged or loose hoses and fittings.
9
Cold air shall be directed away from the hands.
9
DO NOT exceed the maximum air pressure stated on the tool.
8
DO NOT carry an air tool by the hose.
8
Exposure to vibration can cause disabling damage to the nerves and blood supply of the hands and arms.
9
Wear warm clothing when working in cold conditions and keep your hands warm and dry.
9
Operate and maintain the power tool as recommended in the instructions handbook, to prevent an unnecessary increase in
9
vibration levels.
DO NOT use worn or ill-fitting sockets or extensions, as this is likely to cause a substantial increase in vibration.
8
Slips, trips and falls are major causes of workplace injury.
9
Be aware of slippery surfaces caused by the use of the tool and also of trip hazards caused by the air line or hydraulic hose.
9
Proceed with care in unfamiliar surroundings. Hidden hazards, such as electricity or other utility lines, can exist.
9
Use only sizes and types of accessories and consumables that are recommended by the manufacturer; DO NOT use other types or
9
sizes of accessories and consumables.
When using a power tool for, the operator can experience discomfort in the hands, arms, shoulders, neck, or other parts of the body.
9
While using the tool, the operator should adopt a comfortable posture while maintaining secure footing and avoiding awkward or off-
9
balanced postures.
The operator should change posture during extended tasks, which can help avoid discomfort and fatigue.
9
If the operator experiences symptoms such as persistent or recurring discomfort, pain, throbbing, aching, tingling, numbness, burning
9
sensations or stiffness, these warning signs should not be ignored. The operator should tell the employer and consult a qualified health
professional.
WARNING!:The use of the tool can expose the operator's hands to hazards including crushing, impacts, cuts and abrasions and heat.
‰
Wear suitable gloves to protect hands.
© Jack Sealey Limited
PNEUMATIC DIESEL INJECTOR PULLER
MODEL NO:
Wear protective
Wear protective
clothing gloves
Original Language Version
VS2080
Wear ear
protection
VS2080 Issue 1 16/10/2023