Summary of Contents for Dynisco DYMT
- Page 1 Operating Manual Melt Temperature Sensor DYMT Dynisco Europe GmbH Tel: +49 7131 297-0 Wannenäckerstr. 24 Fax:+49 7131 23260 74078 Heilbronn Email: DyniscoEurope@dynisco.com Germany...
-
Page 3: Table Of Contents
Contents Page Contents Technical data Instructions Product description General instructions Safety instructions 3.3.1 Hazard points 3.3.2 Disposal Assembly / installation / disassembly Storage Packaging and transport Installatoin instructions Assembly / commissioning Disassembly Safety features Value tables 4.7.1 Base values Pt 100 in accordance w. DIN EN 60751 11 4.7.2 Base values of the thermal voltages in mV Manufacturer's Declarations Resistance thermometer... -
Page 4: Technical Data
2. Technical data Thread 1/2”-20 UNF, M18 x 1.5 or M14 x 1.5 Stem length 152 mm standard, other lengths on request Blade length 2.5 - 3.0 mm, as requested by customer Material in contact with the medium 15-5 PH SST mat. no. 1.4545 Coatings on request Max. - Page 5 Order specifications:...
-
Page 6: Instructions
Instructions Product description Prescribed use Melt temperature sensors from Dynisco have been especially developed for melt and core temperature detection in extrusion processes in accordance with customer- specific and industry-specific solutions. These sensor designs are basically considered to be "medium contacting"... -
Page 7: Safety Instructions
Safety instructions 3.3.1 Hazards Attention! A burn hazard exists in the entire area of the heated extruder. There is a hazard of hot medium escaping under high pressure through improper assembly or disassembly of the melt temperature sensor when charging with pressure. 3.3.2 Disposal The manufacturer can ensure proper and environmentally friendly disposal. -
Page 8: Assembly / Installation / Disassembly
4. Assembly / installation / disassembly Storage Storage temperature range: -40°C to +70°C, rel. humidity <95% Packaging and transport In order to achieve optimal measurement results with our sensors, ensure the protective cap remains intact to protect the sensor tip. Any damage to the sensor can result in incorrect measurements or failure, in addition defects can occur on your machines due to damaged melt temperature sensors. - Page 9 The length of the sensor blade projecting into the melt should always be selected in such a manner that the measuring point is positioned one third of the channel diameter from the inner wall of the channel. When screwing into place pay attention to the direction arrow on the hexagon (SW14).
-
Page 10: Disassembly
Mounting holes: Melt temperature sensor with ½-20 UNF thread Melt temperature sensor with M18 x 1.5 thread Disassembly To remove after operation, the machine must be empty, however it still should be tempered. Product remnants must be removed when hot without the use of sharp-edged tools. -
Page 11: Safety Features
Do not use the connection line of the temperature sensors as a transport aid! Always place the supplied protective cap on for intermediate storage. In order to ensure a production flow without melt temperature sensor, same size sealing bolts are available, if needed. Safety features Only use proper, intact tools when assembling or disassembling. -
Page 12: Base Values Of The Thermal Voltages In Mv
Grundwer te 4.7.2 Base values of the thermal voltages in mV d er Thermospannungen i n mV Temp er at ur d er Ver gl ei chsstelle ( Bezugstemp er at ur ) 0 °C Grund werte der Thermospannungen in mV Kur zzeichen d es Fe-CuN i Fe-CuNi... -
Page 13: Manufacturer's Declarations
5. Manufacturer's Declarations Resistance thermometer in accordance with EU Machinery Directive 89/392/EEC, Annex II B We hereby declare the temperature sensors delivered to you do not fall under the Directives listed below. EMC Directive ( 89/335/EEC) (in accordance with the German Electromagnetic Compatibility Act Section (EMVG §5 S3)) Low Voltage Directive... -
Page 14: Type "J" Thermocouple
Type "J" thermocouple in accordance with EU Machinery Directive 89/392/EEC, Annex II B We hereby declare the temperature sensors delivered to you do not fall under the Directives listed below. EMC Directive ( 89/335/EEC) (in accordance with the German Electromagnetic Compatibility Act Section (EMVG §5 S3)) Low Voltage Directive (73/23/EEC) And fundamentally not under... -
Page 15: Type "K Thermocouple
Type "K thermocouple in accordance with EU Machinery Directive 89/392/EEC, Annex II B We hereby declare the temperature sensors delivered to you do not fall under the Directives listed below. EMC Directive ( 89/335/EEC) (in accordance with the German Electromagnetic Compatibility Act Section (EMVG §5 S3)) Low Voltage Directive (73/23/EEC) And fundamentally not under... - Page 16 Dynisco SPOL, S.R.O. Dynisco Instruments cp. 579 38 Forge Parkway 756 55 Dolni Becva Franklin, MA 02038 Czech Republic Tel: +42 0571 647728 Tel: +1 508 541 9400 Fax: +42 0571 647224 Fax: +1 508 541 9437 Email:Dyniscocz@nextra.cz Email: InfoInst@dynisco.com Dynisco B.V.
Need help?
Do you have a question about the DYMT and is the answer not in the manual?
Questions and answers