Table of Contents
Advertisement
PLAYBACK
¡ REPEATING PLAY (REPEAT)
Repeating a CD:
e Press REPEAT 77 before or during playback of the CD.
— REPEAT DISC lights up; the CD will now be repeated
continuously.
e Press REPEAT twice to stop the CD being repeated.
Repeating all CDs:
e Press REPEAT 17 twice before or during playback.
— REPEAT lights up; all CDs will now be repeated continuously.
e Press REPEAT again to stop the CDs being repeated.
CALLING UP INFORMATION ON THE DISPLAY (DISPLAY)
In STOP mode:
Text display
— After loading the CDs and closing the CD compartment, the
display shows the number of the CD to be played (= default
display in STOP mode).
During play:
1. Time display
— When you start play (from STOP mode), the display shows
the elapsed playing time of the current track (= default
display in PLAY mode).
As
He E x
e Press DISPLAY 77 whenever you want to know the
remaining playing time of the current track (REM TRACK
TIME).
sly
aK
mack
DN
EN
es
»
4
%
4
7
4
3
19
41
e Press DISPLAY again if you wish to know the remaining
playing time of the entire CD (TOTAL REM TIME).
SZ sacx vom
aS 2 ile =
O
4133
4
7
4
9
1
Note - TOTAL REM(aining) TIME indication is not available in
SHUFFLE mode.
e |f you wish to know the total playing time of the CD, you
must go back to STOP mode first and then press DISPLAY.
— The display now shows the number of tracks and the total
playing time of the current CD (TOTAL TIME).
2, Text display
e lf you press DISPLAY again, you will switch to text display;
the display shows the number of the current CD.
12
ACTIVATING THE FADE- IN AND FADE-OUT FUNCTION
(FADER)
NOTE!
The FADER function can be used if the changer is connected to
the amplifier or the system via the ANALOG OUT output or the
DIGITAL OUT output.
e During play press FADER 77.
— The sound level will now gradually decrease (FADE OUT),
after which the changer will go into the PAUSE mode.
e Press FADER again.
— Play continues and the sound level will increase again to the
originally set level (FADE IN).
SEARCHING FOR THE LOUDEST PASSAGE
(PEAK SEARCH)
e In STOP mode, press PEAK SEARCH 79.
— SELECT DISC lights up.
e Select the number of the required CD using DISC SELECT 6
or DISC 6 (on the remote control - CDC 926 only).
— The CD will now be scanned for the loudest passage (the
peak).
— The display shows the track being scanned and its elapsed
playing time.
— When the loudest passage has been found, it will be
repeated continuously (from 2 seconds before the peak until
2 seconds after the peak)
e You can now adjust your recording device.
e You can stop the scan by pressing STOP/CP 73: if you press
PLAY/REPLAY 74, the CD will be played from the beginning.
NOTE!
— When searching for the loudest passage in a programme,
(from one or more CDs) there is no need to enter the CD
number(s).
— If you wish to record tracks from different CDs, you have to
repeat peak search for each CD.
ADJUSTING THE SOUND LEVEL
(- VOLUME + - CDC 926 only)
NOTE!
— Use the — VOLUME + keys (on the remote control - CDC
926 only) only if the player is connected via the ANALOG
OUT output or the DIGITAL OUT output to an amplifier or
HiFi system without its own control.
— The setting chosen with — VOLUME + will be cancelled
when the player is switched off.
e Hold - VOLUME 7 (on the remote control) pressed down.
— The output signal from the player will now decrease
gradually.
— The successive steps are shown on the display.
e Release the key as soon as the required sound level is obtained.
e Hold VOLUME + 7 (on the remote control) pressed down.
— The output signal will now increase again gradually to the
maximum level.
e Release the key as soon as the required sound level is obtained.
Advertisement
Table of Contents
