Crestron DigitalMedia HD-TX-4KZ-421-CHGR Manual

HD-TX-4KZ-421-CHGR
DM Lite® 4K60 4:4:4 Transmitter and 4x1 Auto-Switcher for HDMI® and
USB-C® DisplayPort™ Signal Extension over CATx Cable with Device
Charging
Interoperability with a DM Lite® receiver or DMPS Lite™
l
switcher
Point-to-point extension of an HDMI® or USB-C®
l
DisplayPort™ signal over a CAT5e or higher cable
USB-C inputs with DisplayPort Alt Mode capability
l
DM Lite transmission distance up to 130 ft (40 m) for UHD
l
and 4K signals or up to 230 ft (70 m) for 1080p, WUXGA,
and 2K signals
4K60 4:4:4 capability
l
HDR10, HDR10+, and Dolby Vision® video formats
l
Compliance with HDCP 2.3
l
Automatic switching of HDMI and USB-C DisplayPort
l
inputs
Charging capability provided by the USB-C DisplayPort
l
inputs
CEC (Consumer Electronics Control) pass-through
l
capability
EDID pass-through capability
l
Compact, surface-mountable design
l
Power from 24VDC power pack (included) or from remote
l
DM Lite receiver or DMPS Lite switcher
The HD-TX-4KZ-421-CHGR is a DM Lite® 4K60 4:4:4
transmitter designed to interoperate with a DM Lite® receiver
or DMPS Lite™ switcher. The paired transmitter and receiver
enable extension of HDMI® or USB-C® DisplayPort™ AV
signals. This is useful in applications where an AV source is
located remotely from its destination, such as a display,
projector, or codec solution. A CAT5e or higher twisted pair
cable must used to connect the HD-TX-4KZ-421-CHGR to the
DM Lite receiver or DMPS Lite switcher.
Interoperability with a DM Lite Receiver or DMPS Lite
Switcher
The DM Lite output port of the HD-TX-4KZ-421-CHGR must
be connected to a DM Lite input port of a DM Lite 4K60 4:4:4
receiver, DM Lite 4K60 4:2:0 receiver, or DMPS Lite switcher.
The HD-TX-4KZ-421-CHGR can be configured and controlled
only when it is used with a DMPS Lite switcher. The web
interface of the switcher can be used to configure the
HD-TX-4KZ-421-CHGR. In addition, control system
programming and .AV Framework™ software support of the
HD-TX-4KZ-421-CHGR is hosted by the switcher.
4K60 4:4:4 and HDR Support
The HD-TX-4KZ-421-CHGR supports video resolutions up to
4K60 with 4:4:4 color sampling. HDR10, HDR10+, and Dolby
Vision® video formats are also supported.
Automatic Switching of Inputs
When the HD-TX-4KZ-421-CHGR is used with a DMPS Lite
switcher, the web interface of the switcher or control system
programming hosted by the switcher can be used to configure
AV switching behavior. Switching among the HDMI and
USB-C DisplayPort inputs occurs based on the last connected
input or on the routing priority assigned to each input. In
addition, input selection push buttons on the front panel of
the HD-TX-4KZ-421-CHGR enable the desired input to be
selected manually.
USB-C DisplayPort Inputs with Charging Capability
When the HD-TX-4KZ-421-CHGR is powered by the included
power pack, each USB-C DisplayPort input can charge a
connected AV source such as a laptop with up to 60W of
power. If the HD-TX-4KZ-421-CHGR is powered by a remote
DM Lite receiver or DMPS Lite switcher, no charging capability
is provided by the USB-C inputs.
Compact, Surface-Mountable Design
Compact in design, the HD-TX-4KZ-421-CHGR can be
mounted onto a flat surface such as the underside of a table,
behind a credenza, or inside a podium. It can also be attached
to a single rack rail in the back of an equipment cabinet.
The HD-TX-4KZ-421-CHGR can receive power from the
included power pack or from the remote DM Lite receiver or
DMPS Lite switcher.
1
2
3