Advertisement
Quick Links
Remote Controller Wireless Kit
Kit de télécommande sans fil
Set der drahtlosen Fernbedienung
Kit per telecomando via radio
Juego de Controlador Remoto Inalámbrico
Kit do controlador remoto sem fios
Draadloze afstandsbedieningsset
Áóýñìáôï Êéô ÓõóêåõÞò Ôçëå÷åéñéóìïý
Model/Modèle/Geräte/Modello/Modelo/Modelo/Model/ÌïíôÝëï/
TCB-AX21E
INSTALLATION MANUAL
MANUEL D’INSTALLATION
INSTALLATIONS-HANDBUCH
MANUALE DI INSTALLAZIONE
MANUAL DE INSTALACIÓN
MANUAL DE INSTALAÇÃO
INSTALLATIEHANDLEIDING
ÅÃ×ÅÉÑÉÄÉÏ ÅÃÊÁÔÁÓÔÁÓÇÓ
Advertisement
Related Manuals for Toshiba TCB-AX21E
Summary of Contents for Toshiba TCB-AX21E
- Page 1 INSTALLATIEHANDLEIDING ÅÃ×ÅÉÑÉÄÉÏ ÅÃÊÁÔÁÓÔÁÓÇÓ Remote Controller Wireless Kit Kit de télécommande sans fil Set der drahtlosen Fernbedienung Kit per telecomando via radio Juego de Controlador Remoto Inalámbrico Kit do controlador remoto sem fios Draadloze afstandsbedieningsset Áóýñìáôï Êéô ÓõóêåõÞò Ôçëå÷åéñéóìïý Model/Modèle/Geräte/Modello/Modelo/Modelo/Model/ÌïíôÝëï/ TCB-AX21E...
- Page 2 Spiegare chiaramente il contenuto del Manuale del proprietario e consegnarne una copia all'utente. Muchas gracias por haber adquirido el control remoto TOSHIBA para su aparato de aire acondicionado. Lea atentamente este manual del propietario antes de utilizar el control remoto para el aparato de aire acondicionado.
- Page 3 CONTENTS Accessory parts ................1 Slide switch ..................9 Switch location of receiver unit ............2 Self-diagnosis table and measures ..........9 Installation location of receiver unit ...........2 Cautions for installation of the remote controller ......10 How to install the receiver unit ............3 Explanation to customers ...............
- Page 4 CONTENTS Accessory parts Parts Quantity Separate receiver unit (provided 200mm power cable) Plate mounting Screws M4 x 25 Screws M4 x 40 Wood screws Spacer Wire joints Clamp Pattern template 95 x 51...
- Page 5 Switch location of receiver unit Address selector switch This switch is used to address one of a maximum of six air con- ditioners that can be controlled by the remote controller. /NORMAL selector switch Set this switch to the “NORMAL” position for the normal operation of the air conditioner. When this switch is set to the “ALL ”...
- Page 6 How to install the receiver unit NOTES : • To avoid malfunction of the remote controller, do not assemble or run remote control wiring together with the power cables, and do not enclose them in the same metal conduit. • When the power unit induces electrical noise, it is recommended that a noise filter or the like be installed.
- Page 7 When using exposed mounting for the receiver unit, install onto a wall where the receiver unit can be attached. 1. Insert a flathead screwdriver or similar tool Face plate into the groove on the bottom of the receiver unit. Pry open with the screwdriver and remove the lower case.
- Page 8 If the separate receiver unit is installed on the ceiling, use the provided ceiling mounting bracket for installation. 1. Insert a screwdriver or similar tool into the notch at the bottom to remove the receiver nameplate. 2. Cut a section out of the ceiling along the provided paper pattern (95 x 51 mm).
- Page 9 How to perform cabling of sensor units Flush Mounting Indoor unit remote Separate receiver controller terminal • Connection diagram unit board Wire of Power wire from receiver unit receiver unit (field supply) Connector • Provided wire joint (WHT 2) 1. Strip the insulation to approximately 14 mm Wire of receiver unit from the ends of the wires to be connected.
- Page 10 Requirement The control by two remote controllers is enabled by installing the wireless remote controller with the wired remote controller for an indoor unit. (Max. 2 remote controllers of wireless or wired are insatiable.) “2-remote controllers” controlling means that one or multiple units are operated by the multiple remote controllers.
- Page 11 How to set the room temperature sensor • The room temperature sensors are equipped in the indoor unit and the wireless remote controller. One of two sensors works. • The room temperature sensor is set to the indoor unit side at the shipment from the factory. To select the sensor in the remote controller, push the SENSOR button (Right figure) inside of the remote controller cover and check “Main sensor”...
- Page 12 Slide switch • Check the slide switch in the battery box of the remote controller is set to [S] / [A] at shipment from the factory. Select of operation mode follow as below table. S K N A H C Digital Inverter Super Modular Multi Super Modular Multi...
- Page 13 Cautions for installation of the remote controller • To operate the remote controller by fixing it to the wall, etc. with a remote controller holder, turn on the fluorescent lamp, operate the remote controller at the position to be fixed, check the air conditioner normally operates, and then mount it.
- Page 14 Test run Before test run • Before turning on the power supply, carry out the following procedure. 1) Using 500V-megger, check 1MΩ or more exists between the terminal block 1 to 3 and the earth. If 1MΩ or less is detected, do not run the unit. Do not apply to the remote controller circuit. 2) Check the valve of the outdoor unit being opened fully.
- Page 15 85464359606000...