Advertisement
Advertisement
Related Manuals for Riding'Times Z8
Summary of Contents for Riding'Times Z8
- Page 1 Z8 ELECTRIC BIKE OWNER’S MANUAL...
- Page 2 WELCOME Please read this owner's handbook carefully before using your Riding'times order to become thoroughly familiar with the correct operation of your bike's controls, features, capabilities, and limitations. This handbook includes safe riding tips but does not contain any of the techniques and skills necessary to ride an electric bicycle safely.
- Page 3 WARNING 1.Check all parts of the bike and ensure that they are in good condition before riding. If any problems are found, contact the dealer immediately. 2.Obey traffic regulations and do not carry passengers on the bike. 3.Slow down in rainy, snowy, or slippery conditions and increase the braking distance to ensure safety.
-
Page 4: Table Of Contents
TABLE OF CONTENTS 1. Assemble mountain bike 2. Mountain bike parts of the analysis chart 3. Specifications 4. Ba ery instruc ons 5. Instruc on of the dashboard 6. Maintenance and cleaning 7. Troubleshoo ng Instruc ons... -
Page 5: Assemble Mountain Bike
Assemble mountain bike Figure 1 1. Take out of the mountain bike from the box(figure1) Figure 1 Figure 2 2.Assemble the handle bar:Put the handlebar into the center of the ver cal (figure ) bar(figure 1),fasten. the screws by using NO.4 Allen Wrench Quick release Figure 1 Figure 2... - Page 6 Figure 4 Figure 5 4. Assemble the front wheel:Put the front wheel on the suspension fork, disc brake is the le of the vehicle(Figure 1);Take out of the quick release bag from the accessory box,insert to the front wheel axle hole(Figure 2), twist the quick release nut to the right ghtness(Figure 3),move down to remove the handle(Figure 4/5) 3.
- Page 7 Figure 1 Figure2 6:Assemble the front mudguard:Put the mudguard on the wheel,and use the NO.4 Allen wrench and the open spanner fixed the mudguard on the front fork;And then s ll use NO.4 Allen wrench put the mudguard support frame fixed to the le and right of the front fork(Figure 2) right Figure 1 Figure2...
- Page 8 Analy c drawing of various parts of mountain bike 13.Frame 1.Handlebar 12.seat 11.Ba ery 4.Headlight 14.Taillight 5.Shock-absorbing 15.Controller front fork 16.Mudguard 17.Shock absorber 19.Rear disc brake 20.Rear disc 6.Front disc 21.Transmission 7.Tyre 9.Chain 8.Tooth disc 22.Side brace 18.Front disc brake 10.Pedals 2.Dashboard 3.Variable speed dial...
-
Page 9: Specifications
SPECIFICATIONS ProductModel: Z8 Motor :48V Ba ery: 48V 15Ah Load: 130KG Mileage: 40-90KM (Depends on load, terrain and riding habits) Charging me: 6-8hours Wheel diameter:20 inches Charger: 48V2A Ba ery instruc ons 1.Ba ery charging:this car is an external lithium ba ery,which can be removed for charging. - Page 10 Do not short-circuit the pack by directly connec ng the posi ve and nega ve terminal with metal object such wire Do not transport and store the ba ery together with metal objects such as necklaces,hairpins etc. Do not strike or throw the pack. Do not directly solder the pack or ba ery and pierce the ba ery with a nail or other sharp object.
-
Page 11: Instruc On Of The Dashboard
9.Mechanical shock LIP cells have less mechanical endurance than metal-can-cased LIB. Falling,hi ng,bending,etc.may cause degrada on of LIP characteris cs. Instruc ons of the Dashboard 1.Product name and model Intelligent LCD display for e-bike;model:YL81C. 2.Specifica ons 36V/48V power supply Rated working current 15mA Maximum working current 30mA Leakage current at power-off<1uA Working current at the supply controller end 50mA... - Page 12 4.Func on overview and func onal area layout (1).Func on overview Display YL81C provides a variety of func ons tomeet the riding needs of users,including: Ba ery level indicator Assist level adjustment and indica on Headlight indicator Speed indicator :including real- me speed,maximum speed(MAXS) and average speed(AVG) Distance indicator:including ODO and trip distance(Trip) Error code indicator...
- Page 13 ODO(km),maximum speed(km/h) and average speed(km/h).When the distance reaches 9999.9km,it will be automa cally reset to zero. Trip distance indicator Average speed indicator Maximum speed indicatorr Display Interface Switching (3).Push assistance By pressing and holding the bu on the electric push a ssistance mode will be enabled.Your e-bike will run at the constant speed of 6km/h.The display will show level p.By releasing the bu on,your e-bike will immediately stop power output and return to the state before push...
- Page 14 (4).Assist level selec on By pressing the bu on / ,the e-bike assist level will be switched to change the motor output power.The assist levels available for the display levels 0-5. Assist Level Switching Interface (5).Ba ery level indicator The ba ery level indicator consists of five segments.When the ba ery is fully charged,the five segments will be all on.ln case of undervoltage, the outline of the ba ery indicator will flash,which means the ba ery has to be charged immediately.
- Page 15 Error Code Indicator Interface When an error code appears on the display interface,please conduct troubleshoo ng in me.Otherwise,your e-bike will not work normally. 6.General se ng All parameters can only be set when your e-bike stops.The steps for general se ng are as follows:In the power-on state,when the display shows the speed of 0.
- Page 16 The steps fo customse ng are as follows: In the power-on state,when the display shows the speed of 0. Press and hold the bu ons and at the same me for more than 2 seconds to enter the selec on interface of custom se ng op ons. Press the bu on / to switch the selec on interface of general se ng op ons,and press the bu on to enter the parameter modifica on interface.
- Page 17 Wheel Diameter Se ng Interface (3).Speed limit se ng P3 represents the speed limit se ng op on.The adjustable range is 10~40km/h.Press the bu on to enter the parameter modifica on interface.Press the bu on / for parameter selec on.Press the bu on to save the parameter and return to the selec on interface of general se ng op ons.
- Page 18 (5).Speed sensor se ng P5 refers to speed sensor se ng op on,which can be set according to the number of magne c heads installed on the wheels of your e-bike. The se ng range is 1-63.Press the bu on to enter the parameter modifica on interface.Press the bu on / for parameter selec on.
- Page 19 Assistance Sensor Se ng Interface 8.Quality commitments and warranty scope (1).Warranty informa on For the faults caused by the quality of the product under normal use, theCompany will be responsible for providing limited warranty during the warranty period. The warranty period of the product is within 12 months from delivery. (2).Non-warranty scope The ceclosure is opened The connector is damaged...
-
Page 20: Maintenance And Cleaning
Maintenamce and cleaning 1.If your bike is very dirty,please clean it with water or mild detergent and non abrasive sponge Driving. 2.Do not use high pressure to wash the bicycle. 3.Never wash the bearing points or electronic components of the electric bicycle directly. - Page 21 2.Vehicle line diagram Ba ery discharge line Motor line Display cable Boost sensor Acceleration handle Headlight line Three-in-one switch Tail light line Brake line Brake line...
Need help?
Do you have a question about the Z8 and is the answer not in the manual?
Questions and answers
How can change kmh to mph ???
To change the speed unit from km/h to mph on the Riding'Times Z8, access the metric/imperial system setting (P4). Follow these steps:
1. Enter the parameter modification interface.
2. Navigate to the P4 setting.
3. Select 01 to switch to the imperial system (mph) or 00 for the metric system (km/h).
4. Save the setting to apply the changes.
This answer is automatically generated
anybody have trouble getting the battery out.....key turns but can't get the battery to "release"
To remove the battery from the Riding'Times Z8 when the key turns but the battery won't release, follow these steps:
1. Ensure the Key is Fully Turned: Turn the key completely to the unlock position.
2. Hold the Battery Securely: Grip the battery firmly with both hands to prevent it from falling.
3. Gently Pull the Battery: Try pulling the battery straight out while ensuring it is fully unlocked.
4. Check for Obstructions: Inspect if any dirt, debris, or misalignment is preventing the battery from releasing.
5. Apply Light Wiggle Movement: Slightly wiggle the battery while pulling to help release any stuck parts.
If the battery still does not release, check for any mechanical issues with the lock mechanism.
This answer is automatically generated
My z8 just stopped working when i use the throttle it does not work?
The Riding'Times Z8 may not be responding when using the throttle due to the following possible reasons:
1. Brake System Issue – The brake system is designed to cut off power to the motor when the brakes are engaged. Check if the brake levers are stuck or incorrectly adjusted.
2. Battery Issues – Ensure the battery is fully charged, securely installed, and properly connected. A low or disconnected battery can prevent the throttle from working.
3. Loose Handlebar Components – Inspect the handlebar grips, variable speed dial, and acceleration handle for any loose connections and tighten them if necessary.
4. Electrical Connection Problems – Verify that all wiring, especially around the throttle and controller, is properly connected and not damaged.
Perform these checks to identify and resolve the issue.
This answer is automatically generated
We hat is the cable connector that runs inside frame to back tire? How do I know if on properly
The cable connector for the Riding'Times Z8 that runs inside the frame to the back tire is the motor line. To check if it is installed correctly, inspect the connecting line for any visible damage and ensure it is securely connected. If there is a fault, refer to the error code definition table to identify issues based on displayed fault codes.
This answer is automatically generated
It is onlying going 25mph at full charge and Amazon said 27/31