Kenwood NX-820G Quick Start Manual page 55

Item
Panel tuning mode
8. Squelch 1) Adj item: [SQLT]
(Tight) Adjust: [∗∗∗.]
2) Adj item:
[Analog [S.QLT]→
Narrow] [S.Q.LT]→
[S.Q.L.T]→
[S.Q.L.T.]→
[S.Q.L.T. _.]
SSG output: 12dB
SINAD level + 4dB
(MOD: 1kHz/±1.5kHz)
[Analog 1) Adj item: [SQLT]
Wide 4k] Adjust: [∗∗.∗.]
2) Adj item:
[S.QLT]→
[S.Q.LT]→
[S.Q.L.T]→
[S.Q.L.T.]→
[S.Q.L.T. _.]
SSG output: 12dB
SINAD level + 4dB
(MOD: 1kHz/±2.4kHz)
[Analog 1) Adj item: [SQLT]
Wide 5k] Adjust: [∗.∗.∗.]
2) Adj item:
[S.QLT]→
[S.Q.LT]→
[S.Q.L.T]→
[S.Q.L.T.]→
[S.Q.L.T. _.]
SSG output: 12dB
SINAD level + 4dB
(MOD: 1kHz/±3kHz)
ADJUSTMENT
Condition
PC test mode
equipment
1) Adj item: [Tight SSG
Squelch (Analog AF VM
Narrow)] 4Ω
2) Adj item: [Low], Dummy
[Low'], [Center], load
[High'], [High] Distortion
Press [Apply All] meter
button to store the Oscillo-
adjustment value. scope
1) Adj item: [Tight
Squelch (Analog
Wide 4k)]
2) Adj item: [Low],
[Low'], [Center],
[High'], [High]
Press [Apply All]
button to store the
adjustment value.
1) Adj item: [Tight
Squelch (Analog
Wide 5k)]
2) Adj item: [Low],
[Low'], [Center],
[High'], [High]
Press [Apply All]
button to store the
adjustment value.
NX-820(G)/820
Measurement
Test- Termi-
Unit Unit
nal
ANT
Ext.SP
con-
nector
Adjustment
Specifi cations/
Parts Method
[Panel tuning mode] "Squelch (Tight)"
After input signal will not be adjusted
from SSG, press correctly if MOD or
[ ] key to store Deviation is wrong.
the adjustment
value. Remark:
During production, a
[PC test mode] fi xed value is written.
After input signal
·Analog Narrow
from SSG, press
[S.QLT]→ 248
[Apply] button to
[S.Q.LT]→ 248
store the adjust-
[S.Q.L.T]→ 248
ment value.
[S.Q.L.T.]→ 248
[S.Q.L.T._.]→ 248
·Analog Wide 4k
[S.QLT]→ 252
[S.Q.LT]→ 252
[S.Q.L.T]→ 252
[S.Q.L.T.]→ 252
[S.Q.L.T._.]→ 252
·Analog Wide 5k
[S.QLT]→ 255
[S.Q.LT]→ 255
[S.Q.L.T]→ 255
[S.Q.L.T.]→ 255
[S.Q.L.T._.]→ 255
Remarks
55