Download Print this page

Advertisement

Available languages

Available languages

Quick Links

校正用
AMS-EN �����������������������
Bar code reader for AMS-EN series (optional)
AMS-EN 系列用条码阅读器(选购项目)
�扱説明書 / パ�ツ�スト
INSTRUCTION MANUAL / PARTS LIST
使用说明书 / 零件表
安全に使用していただくために使用前に、必ずこの取扱説明書をお読みください。
また、いつでもすぐに読めるように、この取扱説明書を保管してください。
警告
注意
Be sure to read this instruction manual before using the product for safe use of the product.
Furthermore, keep this instruction manual close by so that it is available whenever needed.
WARNING :
• Do not look directly into the laser beam of the bar code reader.
• Do not emit laser beam toward human eyes.
• Do not look into the laser beam directly using an optical device.
CAUTION :
When installing this product, be sure to turn OFF the power of the sewing machine.
Furthermore, read the instruction manual of the sewing machine as well.
为了安全地使用,请您在使用之前一定阅读本使用说明书。
另外,请您注意保管本使用说明书,以便随时查阅。
警告
注意
�����������������������
・バーコード読み取り装置のレーザ一光を直接覗かないでください。
・人の目に向けてレーザ光を射出させないでください。
・光学機器で直接レーザ光を覗き込まないでください。
当製品を装着する際は、必ずミシンの電源スイッチを切ってください。
また、ミシンの取扱説明書をあわせてお読みください。
· 请不要直接用眼睛去看条码阅读器的激光光线。
· 请不要对着人的眼睛放射激光。
· 请不要用光学仪器直接窥看激光光线。
安装本产品时,请一定关掉缝纫机的电源开关。
另外,请同时参阅缝纫机的使用说明书。
No.1535-00
40089259

Advertisement

loading
Need help?

Need help?

Do you have a question about the AMS-EN Series and is the answer not in the manual?

Questions and answers

Summary of Contents for JUKI AMS-EN Series

  • Page 1 校正用 AMS-EN ����������������������� ����������������������� Bar code reader for AMS-EN series (optional) AMS-EN 系列用条码阅读器(选购项目) �扱説明書 / パ�ツ�スト INSTRUCTION MANUAL / PARTS LIST 使用说明书 / 零件表 安全に使用していただくために使用前に、必ずこの取扱説明書をお読みください。 また、いつでもすぐに読めるように、この取扱説明書を保管してください。 ・バーコード読み取り装置のレーザ一光を直接覗かないでください。 警告 ・人の目に向けてレーザ光を射出させないでください。 ・光学機器で直接レーザ光を覗き込まないでください。 注意 当製品を装着する際は、必ずミシンの電源スイッチを切ってください。 また、ミシンの取扱説明書をあわせてお読みください。 Be sure to read this instruction manual before using the product for safe use of the product.
  • Page 2 校正用...
  • Page 3 校正用 日本語...
  • Page 4 校正用 目 次 1. 取り付け手順 ...........................1 2. バーコードの貼付け .......................3 3. バーコード機能について ......................3 4. バーコード機能の設定 ......................4 5. 使用方法 ...........................6 6. バーコード構成 ........................7 7. バーコードリーダーの動作不良について ................8...
  • Page 5 校正用 注意 不意の起動による事故を防ぐため、必ず電源を切ってから行ってください。 1. ��付け手順 1)   バーコードリーダー 1 を付属の ねじ 2 、座 金 3 で取付板 4 に取り付けます。    (2 箇所) 2)   ミシン本体の中押えカバーの止めねじ 5 (2 箇所)を一度外し、取付板 4 を取り付け、 再度ねじ止めして、ミシンに取り付けます。 – 1 –...
  • Page 6 校正用 3)   電装ボックスを開けて、   MAIN基板 6 の CN50 に中継ケーブル 7 を接続します。 CN50 9P 白 4)   電装ボックスから出した中継ケーブル 7 を AMS-210EN バーコードリーダー 1 のケーブルと接続し、 ミシンについているケーブルクリップ 8 及 び付属の束線バンド 9 を使用して固定して ください。 AMS-221EN(後方) AMS-221EN(前方) – 2 –...
  • Page 7 校正用 ・バーコード読み取り装置のレーザ一光を直接覗かないでください。 警告 ・人の目に向けてレーザ光を射出させないでください。 ・光学機器で直接レーザ光を覗き込まないでください。 2. �����の貼付け 1)   バーコード 1 は取扱説明書の巻末に添付さ れたものをコピーして使用してください。 2)   外押えへのバーコードの貼付けについては、 図のようにバーコード読取装置からのレーザ 照射がバーコードに当たるように、押え位置 を調整してください。   ("4-3. 固定対比位置の設定 " P. 5 を参照し てください。 ) 3. �����機能について バーコード機能とは、カセット識別等の用途で、バーコードを読み取り、対応した縫製パターンに切 り替えて縫製できる機能です。 バーコードの読み取りにより、ミシンメモリ内に保存されたユーザパターン 999 個、パターンボタン に登録されている縫製データ 50 個に切り替えることが可能です。 使用するためには、AMS-EN バーコードオプションが必要になります。 –...
  • Page 8 校正用 4. �����機能の設定 4-1. バーコード機能の設定 メモリスイッチ K130 では、バーコードモードを選択します。メモリスイッチ Kxxx( レベル 2) の選 択方法は、サービスマニュアルを参照ください。 設定 内容 説明 バンク ・ バーコー バンク・バーコード機能を使用し ド無効 ません。 バンク数 2 バンク数に 2 パターンを設定しま す。 バンク数 4 バンク数に 4 パターンを設定しま す。 バンク数 8 バンク数に 8 パターンを設定しま す。 バンク数...
  • Page 9 校正用 4-3. 固定退避位置の設定 バーコード機能では、メモリスイッチ K117 A 、K118 B の固定退避位置座標が有効になります。押 えに貼られたバーコードの読み取り位置に調整が必要な場合に、設定をしてください。メモリスイッ チ K90 固定退避位置選択を設定する必要はありません。 設定 内容 説明 固定退避位置・X 座標 X 軸方向の固定退避位置を 設定します。 固定退避位置・Y 座標 Y 軸方向の固定退避位置を 設定します。 4-4. バーコードモードを有効にする メモリスイッチ K130 でバーコードモードを選択すると、モード切替画面にバーコードモードボタン  C が表示されます。このボタンを押下すると、バーコードモードの ON/OFF を切り替えること ができます。 ただし、バーコードリーダーが接続されていない、または、接続不良である場合には、モードを ON にすることができません。  バーコードモード ON  バーコードモード...
  • Page 10 校正用 5. 使�方法 モード切替画面を閉じ、バーコードモードが ON であると、ON 状態を示すピクト D が表示されます。 設定状態では、バーコード読み取りによる縫製パターンの確認が可能です。画面上のバーコード読み 取りボタン、     E または、 押え SW( ペダル ) を押下することで、 バーコードの読み取りを行います。 ただし、設定状態での読み取り動作は、原点検索動作以降に有効となります。また、押え SW 押下に よる押えの動作はありません。バーコードの読み取りのみとなります。設定状態で読み込んだ縫製パ ターンは、準備状態移行時に破棄されます。 バーコード読み取り 準備状態では、押え SW 押下により、バーコードの読み取り、パターン読み込み、  外押え下降の動作 になります。 バーコード読み取り 押え下降 縫製パターンが読み込まれ、外押えが下降した状態で縫製開始が可能です。 エラーコード一覧 エラーコード ピクト エラー内容 表示メッセージ 復帰方法...
  • Page 11 校正用 6. �����構成 巻末の付録にあるバーコードシートを読み取ることで、対応する縫製パターンに切り替えることがで きます。切り離してお使いください。バーコードシートは Code39 の規格に対応しています。 Code39 以外の規格でバーコードを作成する場合、下記フォーマットに従って作成してください。 ・4 バイト ASCII コード ・" パターン種別 "、" 百の位 "、" 十の位 "、" 一の位 " D 0 0 1 パターン種別 パターン No. パターン種別   U または 0:ユーザパターンに対応します。   D または 1:パターンボタンに登録されている縫製データに対応します。 パターン No.  ...
  • Page 12 校正用 7. �������ダ�の動作不良について バーコードリーダーが読み取りを行わない場合、バーコードリーダー側面にある SCAN ボタンを押し て、レーザーが発光することを確認してください。 SCAN ボタンを押しても発光しない場合、バーコードリーダーが故障している恐れがあります。 発光する場合には、 下記のバーコードを  1  →  2  →  3  の順で読み取り、 ミシンを再起動してください。 設定開始 初期化 設定終了 – 8 –...
  • Page 13 校正用 ENGLISH...
  • Page 14: Table Of Contents

    校正用 CONTENTS 1. Installation procedure ....................1 2. Attaching the bar code ....................3 3. Bar code function ......................3 4. Setting of the bar code function ................... 4 5. How to use ........................6 6. Bar code configuration ....................7 7.
  • Page 15: Installation Procedure

    校正用 CAUTION : Turn OFF the power before starting the work so as to prevent accidents caused by abrupt start of the sewing machine. 1. Installation procedure Install the bar code reader 1 onto the mounting plate 4 using the screws 2 and the washers 3 (two locations) which are included as the accessories.
  • Page 16 校正用 3) Open the electrical box, and connect the relay cable 7 to CN50 of the main PCB 6 . CN50 9P white Connect the relay cable 7 coming out of the AMS-210EN electrical box to the cable of the bar code reader 1 , and fix it using the cable clip 8 attached to the sewing machine and the bundle wire band 9 which is included as the accessory.
  • Page 17: Attaching The Bar Code

    校正用 WARNING : • Do not look directly into the laser beam of the bar code reader. • Do not emit laser beam toward human eyes. • Do not look into the laser beam directly using an optical device. 2. Attaching the bar code Copy the bar code 1 attached at the end of the instruction manual for use.
  • Page 18: Setting Of The Bar Code Function

    校正用 4. Setting of the bar code function 4-1. Setting of the bar code function On memory switch K130, select the bar code mode. Refer to the engineer’s manual for the selection method of the memory switch Kxxx (level 2). Setting Content Explanation Bank/bar code Bank/bar code function is not used. disabled Number of Two patterns are set as the...
  • Page 19 校正用 4-3. Setting of the fixed escape position According to the bar code function, the fixed escape position coordinate of the memory switch K117 A and K118 B will be effective. Make this setting when adjustment is required for the reading position of the bar code attached to the work clamp foot. It is not required to set the memory switch K90 fixed escape position selection. Setting Content Explanation Fixed escape position • Setting is made for the fixed X coordinate escape position in X axis. Fixed escape position • Setting is made for the fixed Y coordinate escape position in Y axis.
  • Page 20: How To Use

    校正用 5. How to use When the mode switching screen is closed and the bar code mode is ON, a pictograph showing ON state D will be displayed. In the setting state, a sewing pattern by bar code reading can be verified. The bar code can be read by pushing the bar code reading button on the screen E or treading on the work clamp foot switch (pedal).
  • Page 21: Bar Code Configuration

    校正用 6. Bar code configuration By reading the bar code sheet attached at the end of this manual, the sewing pattern can be switched to the one corresponding to the selected bar code. Separate the attached bar code sheet for your use. This bar code sheet is compatible to Code39.
  • Page 22: Malfunction Of The Bar Code Reader

    校正用 7. Malfunction of the bar code reader When the bar code reader does not work, push the SCAN button on the side of the bar code reader to check if there is laser emission or not. If there is no laser emission even if the SCAN button is pushed, the bar code reader may be defective. If the laser is emitted, read the following bar codes in the order of 1 →...
  • Page 23 校正用...
  • Page 24 校正用 目 录 1. 安装顺序 .................................1 2. 条形码的粘贴 ................................3 3. 关于条形码功能 ..............................3 4. 条形码功能的设定...............................4 5. 使用方法 .................................6 6. 条形码的构成 ................................7 7. 关于条形码阅读器的动作故障 ........................8...
  • Page 25 校正用 注意 为了防止突然的起动造成的事故,请一定关掉电源之后再进行操作。 1. 安装顺序 1) 用附属的螺丝 2 、垫片 3 把条形码阅读器 1 安装到安装板 4 上。 (2 处) 2) 暂且卸下缝纫机主机的中压脚护罩的固定螺丝 5 (2 处 ),安装上安装板 4 ,然后再拧上螺丝, 安装到缝纫机。 – 1 –...
  • Page 26 校正用 3) 打开电气箱, 把连接电缆 7 连接到 MAIN 电路板 6 的 CN50 上。 CN50 9P 白色 4) 把从电气箱连接出来的连接电缆 7 连接到条 AMS-210EN 形码阅读器 1 的电缆线上,然后使用缝纫机 上安装的电缆线夹 8 和附属的束线带 9 进行 固定。 AMS-221EN( 后方 ) AMS-221EN( 前方 ) – 2 –...
  • Page 27 校正用 · 请不要直接用眼睛去看条码阅读器的激光光线。 警告 · 请不要对着人的眼睛放射激光。 · 请不要用光学仪器直接窥看激光光线。 2. 条形码的粘贴 1) 请复印使用说明书的卷末附录的条形码 1 供 下面操作使用。 2) 有关在外压脚上粘贴的条形码的粘贴方法,请 如图所示那样调整压脚位置,让条形码阅读器 发射的激光照射到条形码上。 ( 请参照“4-3 固定对比位置的设定”P.5。) 3. 关于条形码功能 所谓条形码功能就是在用于识别卡盒等时,阅读条形码,变换成对应的缝制图案进行缝制的功能。 通过阅读条形码, 可以变换保存在缝纫机存储器内的 999 个用户图案、 50 个等级在图案按钮中的缝制数据。 使用本功能时、需要 AMS-EN 条形码选购项目机器。 – 3 –...
  • Page 28 校正用 4. 条形码功能的设定 4-1. 条形码功能的设定 用存储器开关 K130 选择条形码模式。有关存储器开关 Kxxx( 等级 2) 的选择方法,请参照服务手册。 设定 内容 说明 数据库条形码无 不使用数据库条形码功能。 效 数据库数 2 设定 2 图案到数据库。 数据库数 4 设定 4 图案到数据库。 数据库数 8 设定 8 图案到数据库。 数据库数 16 设定 16 图案到数据库。 条形码模式 使用条形码模式。 4-2.
  • Page 29 校正用 4-3. 固定躲避位置的设定 使用条形码功能时,需要把存储器开关 K117 A 、K118 B 的固定躲避位置坐标变成有效。需要调整粘贴到 压脚上的条形码的读取位置时,请进行设定。不需要设定选择存储器开关 K90 的固定躲避位置。 设定 内容 说明 固定躲避位置 ·X 坐标 设定 X 轴方向的固定躲避位 置。 固定躲避位置 ·Y 坐标 设定 Y 轴方向的固定躲避位 置。 4-4. 把条形码模式设定为有效 用存储器开关 K130 选择了条形码模式之后,在模式变换画面上显示出条形码模式按钮 C 。按了此 按钮之后,可以变换条形码模式的 ON/OFF。 但是,如果没有连接条形码阅读器,或者连接不良时,则不能将模式变为 ON。 条形码模式...
  • Page 30 校正用 5. 使用方法 关闭模式变换画面,显示出条形码模式 ON 和表示 ON 状态的图标 D 。对于设定状态,可以通过读取条 形码确认缝制图案。 按了画面上的条形码读取按钮 E 或者按下压脚 SW( 踏板 ), 就可以读取条形码。 但是,在设定状态下的读取动作在原点检索动作之后变为有效。另外,按压脚 SW 后压脚不动作。仅可 以读取条形码。在设定状态下读取的缝制图案当移动到准备状态后则被取消。 读取条形码 在准备状态下,按了压脚 SW 后,变为可以进行读取条形码、读取图案、下降外压脚的动作。 读取条形码 下降压脚 读取了缝制图案,外压脚下降后的状态下可以开始缝制。 异常代码一览 异常代码 图标 异常内容 显示信息 复位方法 复位位置 E010 条形码规定的图案备由被登记。 没有规定的图 复位后可 前画面 案。...
  • Page 31 校正用 6. 条形码的构成 读取卷末附录中的条形码表, 可以变换成对应的缝制图案。请剪下来使用。条形码表对应 Code39 的规格。 Code39 以外规格编制的条形码时,请按照下列格式进行编制。 ·4 比特 ASCII 代码 ·“图案种类” 、 “百位” 、 “十位” 、 “个位” D 0 0 1 图案种类 图案 No. 图案种类 U 或 0 : 对应用户图案。 D 或 1 : 对应图案按钮中登记的缝制数据。 图案 No. 用户图案:No.001 ~ No.999 图案按钮中登记的缝制数据:No.001 ~ No.050 请用...
  • Page 32 校正用 7. 关于条形码阅读器的动作故障 如果条形码阅读器不能进行读取时,请按条形码阅读器侧面的 SCAN 按钮,确认激光是否发光。 按了 SCAN 按钮也不发光时,有可能是条形码阅读器出了故障。 发光时,请按照 1 → 2 → 3 的顺序读取下列的条形码,然后重新起动缝纫机。 开始设定 初期化 设定结束 – 8 –...
  • Page 33 校正用 PARTS LIST...
  • Page 34 校正用 品     名 REF.NO NOTE PART NO D E S C R I P T I O N バーコードセット A 組 400-89238 BAR CODE SET A ASSY バーコードリーダ組 400-89237 BAR CODE READER ASSY バーコードリーダブラケット 400-89027 BAR CODE READER BRACKET なべ小ねじ M 2 L =6 SM-4020601-SC SCREW M2 L=6 平座金みがき丸 M...
  • Page 35 校正用 BARCODE SHEET...
  • Page 36 校正用...
  • Page 37 校正用 両サイドの余白が小さいと、読取り不良の原因になります。切り取り線に沿って切り離してください。 If the margin on both sides of the bar code is small, it may cause a reading error. Cut the bar codes along the dotted lines. 如果条形码两侧的空白小的话,有可能发生读取异常。请沿着虚线剪下来使用。 ユーザーパターン No. 001 〜 050 / User pattern No. 001 to 050. / 用户图案 No.001 ~ No.050 –...
  • Page 38 校正用 ユーザーパターン No. 051 〜 100 / User pattern No. 051 to 100. / 用户图案 No.051 ~ No.100 – 2 –...
  • Page 39 校正用 ユーザーパターン No. 101 〜 150 / User pattern No. 101 to 150. / 用户图案 No.101 ~ No.150 – 3 –...
  • Page 40 校正用 ユーザーパターン No. 151 〜 200 / User pattern No. 151 to 200. / 用户图案 No.151 ~ No.200 – 4 –...
  • Page 41 校正用 ユーザーパターン No. 201 〜 250 / User pattern No. 201 to 250. / 用户图案 No.201 ~ No.250 – 5 –...
  • Page 42 校正用 ユーザーパターン No. 251 〜 300 / User pattern No. 251 to 300. / 用户图案 No.251 ~ No.300 – 6 –...
  • Page 43 校正用 ユーザーパターン No. 301 〜 350 / User pattern No. 301 to 350. / 用户图案 No.301 ~ No.350 – 7 –...
  • Page 44 校正用 ユーザーパターン No. 351 〜 400 / User pattern No. 351 to 400. / 用户图案 No.351 ~ No.400 – 8 –...
  • Page 45 校正用 ユーザーパターン No. 401 〜 450 / User pattern No. 401 to 450. / 用户图案 No.401 ~ No.450 – 9 –...
  • Page 46 校正用 ユーザーパターン No. 451 〜 500 / User pattern No. 451 to 500. / 用户图案 No.451 ~ No.500 – 10 –...
  • Page 47 校正用 ユーザーパターン No. 501 〜 550 / User pattern No. 501 to 550. / 用户图案 No.501 ~ No.550 – 11 –...
  • Page 48 校正用 ユーザーパターン No. 551 〜 600 / User pattern No. 551 to 600. / 用户图案 No.551 ~ No.600 – 12 –...
  • Page 49 校正用 ユーザーパターン No. 601 〜 650 / User pattern No. 601 to 650. / 用户图案 No.601 ~ No.650 – 13 –...
  • Page 50 校正用 ユーザーパターン No. 651 〜 700 / User pattern No. 651 to 700. / 用户图案 No.651 ~ No.700 – 14 –...
  • Page 51 校正用 ユーザーパターン No. 701 〜 750 / User pattern No. 701 to 750. / 用户图案 No.701 ~ No.750 – 15 –...
  • Page 52 校正用 ユーザーパターン No. 751 〜 800 / User pattern No. 751 to 800. / 用户图案 No.751 ~ No.800 – 16 –...
  • Page 53 校正用 ユーザーパターン No. 801 〜 850 / User pattern No. 801 to 850. / 用户图案 No.801 ~ No.850 – 17 –...
  • Page 54 校正用 ユーザーパターン No. 851 〜 900 / User pattern No. 851 to 900. / 用户图案 No.851 ~ No.900 – 18 –...
  • Page 55 校正用 ユーザーパターン No. 901 〜 950 / User pattern No. 901 to 950. / 用户图案 No.901 ~ No.950 – 19 –...
  • Page 56 校正用 ユーザーパターン No. 951 〜 999 / User pattern No. 051 to 999. / 用户图案 No.951 ~ No.999 – 20 –...
  • Page 57 校正用 ダイレクトパターン No. 001 〜 050 / Direct pattern No. 001 to 050. / 直接图案 No.001 ~ No.050 – 21 –...
  • Page 58 校正用 – 40 –...
  • Page 59 校正用...
  • Page 60 ※この取扱説明書 / パーツリストは仕様改良のため予告なく変更する事があります。 Please do not hesitate to contact our distributors or agents in your area for further information when necessary. Copyright C 2009 JUKI CORPORATION * The description covered in this Instruction Manual, PartsList is subject to change for improvement of •...