Related Manuals for CreatBot D600 Pro 2
Summary of Contents for CreatBot D600 Pro 2
- Page 1 CreatBot 3D Printer User manual English V7.4 Henan Creatbot Technology Limited - 1 -...
-
Page 2: Table Of Contents
CONTENTS Notice ..........................3 Machine Diagram Front..........................4 New Printer Head ....................... 5 Printer Operation Leveling Platform......................7 Load Filament ......................8 Unload Filament......................9 Main menu........................10 Detail page........................12 Axis operation......................13 Filament menu......................14 SD Card/U-disk......................15 Info. menu........................16 Setting menu .......................17 Frequently Asked Questions Change Fuse.........................20 Print PLA and ABS ......................20... -
Page 3: Notice
Please use the filament provided by CreatBot, or high quality filament by third manufacturers. Due to the use of third party inferior material caused by the failure of the printer, the loss will be borne by the user. -
Page 4: Machine Diagram Front
Machine Diagram Front Touch screen Power switch U disk input Indicator light Universal Wheel - 4 -... -
Page 5: New Printer Head
Machine Diagram New Printer Head 1. PCB box 6. Extruder box 2. Filament press button 7. Cooling fan 3. Feeding tube 4. Connector 5. Servo - 5 -... - Page 6 Machine Diagram New Printer Head 1. Extruder motor 4. Heating tube 2. Sink fan 5. Heating sensor 3. Heat sink 6. Hotend - 6 -...
-
Page 7: Printer Operation Leveling Platform
Printer Operation Leveling Platform Leveling nuts 1. Turn on the printer. 2. On the touch screen, press “Move axis” -> “All home”.Then “-Z” —> 100mm. Till “Z” is at 0.00mm. 3. Move the extruder by hand to 4 corners of bed, check the distance between nozzle and bed. -
Page 8: Load Filament
Printer Operation Load Filament Preheat head Straightened filament Load filament 1.Preheat the hotend before loading filament. 2.Straightened filament and check the filament do not self-winding. 3.Thread the filament through the filament detection device and manually load the filament until it exits the feed tube above the extruder. 4.Insert the filament into the gear of the extruder and click Load. -
Page 9: Unload Filament
Printer Operation Unload/Change Filament Unload filament menu Preheat head Pull out filament 1. Enter "Filament" menu ->"Unload filament", and select the head you want unload. 2. Wait for the nozzle heated to a suitable temperature. 3. After reching temperature, feeder will send a certain number of filament, and then automatically withdraw filament. -
Page 10: Main Menu
Printer Operation Touchscreen Main Menu 210 ° C Touch and set up the temp of the nozzle. 210 ° C Preset nozzle temperature Current nozzle temperature 25 ° C 25 ° C Touch and set up the temp of the nozzle. 210 °... - Page 11 Printer Operation Touchscreen Main Menu preheat Open U-disk Cool down USB unavailable Filament menu bed up Move axis bed down resume stop Setting pause - 11 -...
-
Page 12: Detail Page
Printer Operation Touchscreen Detail page Adjust. During printing, you can click itto adjust the print speed fan speed andthe extrusion. Current printing progress pause stop change print speed：100% 100% flow rate：100% 100% colling fan speed：100% 100% - 12 -... -
Page 13: Axis Operation
Printer Operation Axis operation Minimum units Move X to home Move Y to home Move Z to home All axis to home Move Y axis Move X axis Z down/up Back X,Y,Z current position of hotend. - 13 -... -
Page 14: Filament Menu
Printer Operation Filament menu #1 extruder(unavailable) #2 extruder Extrude filament Retract filament Back Click and enter a value load/unload Adjust value when extrude/retract filament - 14 -... -
Page 15: Sd Card/U-Disk
Printer Operation SD Card/U-disk print file2.gcode file2.gcode Click and choose a file to print Last page Superior menu Next page Back - 15 -... -
Page 16: Info. Menu
Printer Operation Info. page 0000:00:00 6.1.XXXXXX 6.1.0 Time used Print time used 0000:00:00 Firmware Firmware version 6.1.XXXXXX UI version UI version 6.0.1 Back - 16 -... -
Page 17: Setting Menu
Printer Operation Setting menu X/Y/Z and exturder motor setting (range:5-9999) Save Back The values in the picture are not real values, the real values refer to the printer default values - 17 -... - Page 18 Printer Operation Setting menu sink fan speed (range:1-100) cooling fan speed (range:1-100) head temperature (range:0-420) hotbed temperature (range:0-100) - 18 -...
- Page 19 Printer Operation Setting menu Enter the WiFi name and password, and click Connect. The printer will automatically connect to WiFi. Only supports 2.4GHz Wi-Fi. - 19 -...
-
Page 20: Frequently Asked Questions
Frequently Asked Questions Change Fuse Open fuse tray Change new fuse Print PLA and ABS Nozzle Close bed Cooling Enclosed Adhesion Tape 200 ℃ 45 ℃ Timed close Max. 100% masking Can open None/Brim 240 ℃ 90 ℃ Always Brim/Raft Max. -
Page 21: Hardware Troubleshoot
Frequently Asked Questions Hardware Troubleshoot 1. Display "MINTEMP" ? The environment is too low, or temperature sensor is damaged, please keep the room temperature above 0 ℃ . 2. Display "MAXTEMP" ? Temperature of nozzle or bed too high, or temperature sensor is damaged, please keep their temperature in a suitable range. -
Page 22: Printing Troubleshoot
Printing Troubleshoot not over 120℃, and you can close the bed above 100mm except printing ABS or other high-temperature required filaments. 3. The model not stick on the platform ? Please paste masking paper or Kapton tape on the platform, or the nozzle is too far away from the platform, or the bottom of the model is not flat. - Page 23 Quality · Experience · Ser vice Henan Creatbot Technology Limited Telephone: +86 4000-558-930 Website: www.CreatBot.com Email: sales@creatbot.com Address: 6#, Chaoya Industr y Park , Hanghai Road, No.13 Ave., Eco-Tech Development Zone, Zhengzhou City, Henan Province, China...
Need help?
Do you have a question about the D600 Pro 2 and is the answer not in the manual?
Questions and answers