Table of Contents
Advertisement
(8) PRESET STATION
INDICATOR
This indicator of the station selected with the PRESET
STATION
button lights.
@ MEMORY INDICATOR
Lights for about 3 seconds after the MEMORY button ®
is pressed.
During this interval the preset memory
loca-
tions may be programmed.
@ POWER SWITCH
|
When power is turned on, illumination lamps above the
PRESET STATION button will igiht, and in a moment the
station selected with INITIAL STATION SET will be tune
in.
See page 8 for INITIAL STATION SET.
@ MULTIPATH SWITCH
Operates only during FM reception. Pushing the switch
lights up the indicator, detects multipath, and indicates
MULTIPATH interference. (Refer to page 7.)
(B RX MODE SWITCH
This switch only operates during FM reception.
The mode is a three state switch-over (AUTO
DX >
ENFORCED
DX > ENFORCED
LOCAL)
mode.
It
switches-over in the above order each time the switch is
pushed and is shown on the indicators. (Refer to page ?
for details)
@® REC CAL SWITCH
This switch provides a signal for setting record levels prior
to recording from the tuner. Pressing the switch activates
the REC
CAL oscillator to send a 333Hz
50%
FM
- modulated
signal
to the output
jacks.
This allows
the
recording level to be set for a "typical" program
level
regardiess of the current
level of the broadcast being
received.
*
The REC CAL switch takes precedence over all other
tuner functions; therefore, it should be left off when
not in use,
@ TUNING MODE SWITCH
Sets the Tuning button for either Auto or Manual opera-
tion,
e AUTO Position (FM STEREO)
The TUNING
MODE
indicator
6) lights, and the auto-
search tuning function of the Tuning button His
activated.
-
In the AUTO
position, any FM stereo broadcast will be
received in stereo.
e
MAN'L/MONO Position (MONO)
The TUNING
MODE
indicator is off, and the manual
tuning function of the Tuning button
@® is activated.
*
in the MAN'L/íMONO position, even FM stereo broad-
casts will be heard in mono.
(BD FM/AM BUTTON
These switches select either FM or AM broadcasts.
@ TUNING
BUTTON
Use this button to tune in broadcast stations.
@
When the TUNING
MODE
switch
@ has been set to
AUTO.
Pressing the DOWN side of the button scans the broadcast
band downwards
until a station is encountered, then stops
with the station perfectly tuned in (Auto-Search Tuning).
Pushing
the button
again scans
progressively
lower
frequencies until the next station is found, When
the
bottom of the band is reached, the frequency is set to the
top of the band and the scan continues downward. Press-
ing the Up side of the button scans the band upwards in the
same way.
e When the TUNING MODE switch ® has been set to
MAN'L.
Pressing the DOWN
side of the buttan scans down the band
only as Jong as the button is held, and pressing the Up
side scans upwards as long as the button is held. In either
case scanning stops when the button is released. Pushing
the Tuning button briefly causes the frequency to advance
0.1MHz on FM or 10kHz on AM.
T-IDOO
@® PRESET STATION
BUTTONS
Use these buttons to select the broadcast station preset
with MEMORY
button.
A total of 10 stations may be preset into the tuner's
MEMORY.
It is not necessary to select the proper band (FM or AM)
before using one of the PRESET STATION
buttons to tune
in a station. The band is memorized to together
with the
station.
The tuning mode (FM stereo or mono) and RX MODE
are also memorized.
|
@ MEMORY
BUTTON
Pushing this button causes the indicator on the button to
light for 3 seconds. Pressing one of the PRESET STATION
-
buttons
(HP while the indicator is lit causes the frequency
of the station currently tuned in to be memorized,
This button is also used to control the Initial Station Set
function. You can preselect the station to be tuned in when
power is first turned on, For details refer to page 8.
Advertisement
Table of Contents
