Philips HB 578 Manual page 6

General description (fig. 1, page 3)
A
Tube lamps and starters of the couch
B
Tube lamps and starters of the canopy
C
Facial tanner
D
Switch(es) for facial tanner
Type HB 578:
O
= facial tanner off
A
= facial tanner on
Type HB 579:
O
= facial tanner off
A and ,
= facial tanner on at 75% of its full power
A and »
= facial tanner on at full power
E
Fan for body cooling
F
Switches for fan
O
= fan off
A and n
= fan on at half power
A and b
= fan on at full power
G
End covers
H
Mains cord
I
Legs of the frame
J
Connecting tubes with protective covers
K
Connecting cord between couch and canopy
L
Fans to cool the tube lamps
M
Vents
N
Acrylic sheets
O
Protective foil
P
Protective goggles (2 pairs)
(type no. HB 072/service no. 4822 690 80147)
Q
Screws, socket-head screws and decorative caps
R
Socket-head screw wrench and screwdriver
S
Pillow
T
Remote control
Making the solarium ready for use
• It requires two people to assemble and move the solarium (fig.
2).
• During assembly the solarium becomes heavier and more difficult
to move. We therefore advise you to assemble the solarium at
the place where it will be used. Make sure there is enough free
space beside (at least 50 cm) and behind (at least 30 cm) the
solarium.
Assembly of the couch
- Assemble the tubes of the frame by means of socket-head
screws (fig. 3).
• Make sure the larger assembly openings in the legs of the frame
are pointing outward.
- Carefully put the couch on the legs. Make sure the legs slide
steadily into the appropriate openings in the couch (fig. 4).
• NB: the connecting tubes of the couch should be pointing
backward.
- Fasten the side panels to the legs of the frame (fig. 5) with the
screws supplied (fig. 6). Slide the front panel behind the edges of
the side panels and fasten it with the screws supplied (fig. 7).
Stick to the order indicated in fig. 5 to ensure that side panels (1)
and (2) enclose the edges of the front panel (3).
- Fasten the front panel to the couch and push the decporative
caps onto the screw heads.
• The only purpose of the panels is to enhance the appearance of
the appliance.
- NB: Only move the couch by carefully sliding its legs across the
floor or by carefully lifting it slightly off the floor together with
another person.
• Never try to move the couch as shown in fig. 8. This could cause
the couch to become detached from the frame.
Assembly of the canopy
- Put the canopy on the floor with the tube lamps pointing
downward (fig. 9).
- Lift the canopy together with another person and position its
connecting tubes over the connecting tubes of the couch (fig.
10).
- Slide the tubes steadily into the connecting tubes of the couch.
Making ready for use
- Push the canopy backward (fig. 11) and remove the protective
foil from the acrylic sheet (fig. 12).
- Insert the connecting cord into the socket in the couch (fig. 13).
See fig. 14 for removal of cord.
- Insert the plug of the solarium into the wall socket.
Use
- Push the canopy backward so that you can lie down on the
couch (fig. 15). When you lie on the couch, pull the canopy back
into horizontal position.
• NB: when the solarium has not been used for some time, the
hinges of the canopy may squeak when you push the canopy
backward and forward the first time.
- Switch the appliance on by setting the required tanning time on
the remote control (see section 'Remote control').
• For the correct tanning times, see the section 'UV tanning
sessions: how often and how long?'.
- Switch the body cooler on by means of the switch (fig. 16) and
select the required setting and power (I and n or b) (fig. 17).
- If you like, you can also switch on the facial tanner (fig. 16).
Type HB 579 only: select setting , for 75% of its full power or »
for full power (fig. 18).
- Don't forget to put on the protective goggles provided.
6