Advertisement
6 Apply cotton to the skin and move the device slowly. (Fig. 6)
●
The mode indicator lamp will turn on and the device will start to vibrate.
●
The time for use is within 3 minutes.
CAUTION
Unless you apply cotton puff to your skin while touching the back plate, the device
will not vibrate. (skin sensing function)
If the heating head is not vibrating, the device is not working.
If you leave the device as it is for about 3 minutes without vibration, the device will
automatically switch "Off." (Automatic shutoff function)
Indicating timer function
Skin care time is indicated by the buzzer beeping about every 45 seconds as a guide.
[Example of skin care sequence]
Divide the area from your face to décolletage into four zones as shown in the
illustration. By moving the heating head in the order of ①②
④décolletage, the whole area can be efficiently and uniformly cared for.
●
Apply the cotton gently to the face and slowly move the device by sliding it from the
center of the face to the outer side.
Do not keep the cotton on the same area of skin, it is necessary to
move it around.
(Cause of problems with your skin or physical discomfort.)
●
Add more toner when there is no moisture in the cotton or when the device is
difficult to slide.
●
Do not apply the device on the same area of skin for more than 10 seconds.
●
If you feel your skin tingling by micro current while using the device, press the Level
switch button and switch to "Low."
If you still feel your skin tingling, use the device by adding more toner.
7 After 3 minutes have elapsed, the device will automatically shut off.
(Auto shutoff function)
●
The finish sound (beep beep) will inform you.
8 After use, make sure to pull out the power adaptor from the electric outlet and the
main body. (Fig. 7)
To continue to use the next mode, do not disconnect the power adaptor.
9 Remove the ring and the cotton.
●
Wipe off the surface of the head with a tissue.
●
Do not use the cotton again once it is used. It might cause problems with your skin.
When not using cotton
If you use a gel-like toner/moisturizing product (all-in-one type toner for moisturizing) or
thick toner which is difficult to permeate the cotton you can use this device without attaching
cotton to the body.
1 Apply a gel-like moisturizing product or thick toner that you would normally use onto the
heating head and smoothen it over the entire head with your fingers. (Fig. 9)
Moisturizing product
2 After confirming that the power adaptor is connected to the main body, press the power
switch. (Fig.8)
●
"Low" on the level indicator lamp lights and "HOT MOISTURIZE" on the mode
indicator lamp starts flashing. If a lamp in another mode is flashing, press the mode
switch button to switch to "HOT MOISTURIZE."
③T-zone
-9-
When the "HOT CLEANSING" mode is finished, press the power switch and the
"HOT MOISTURIZE" mode will automatically be set.
3 Choose "the strength" of electrical potential with the level switch button.
●
Switch the "strength" with the Level switch button according to the condition of your skin.
●
Every time the level indicator button is pressed, the high, medium, and low of the
electrical potential will be switched. There will be no change in vibration strength.
It is recommended that when using the device for the first time or if you feel some
discomfort, use the device in "Low."
4 Hold the device with your hand touching the back plate of the body. (Fig. 5)
●
Make sure to hold the body with your hand touching the back plate.
5 Apply the heating head directly to the skin and move it slowly. (Fig. 6)
●
The mode indicator lamp will switch and turn on, and the device will start to vibrate.
●
The time for use is within 3 minutes.
CAUTION
Unless you apply the heating head to your skin while touching the back plate,
the device will not vibrate. (skin sensing function)
If the heating head is not vibrating, the device is not working.
If you leave the device as it is for about 3 minutes without vibration, the device will
automatically switch "Off." (Automatic shutoff function)
Indicating timer function
Skin care time is indicated by the buzzer beeping about every 45 seconds as a guide.
[Example of skin care sequence]
Divide the area from your face to décolletage into four zones as shown in the
illustration. By moving the heating head in the order of ①②
④décolletage, the whole area can be efficiently and uniformly cared for.
●
Add more toner or moisturizing product when the heating head does not easily slide.
●
Apply the heating head gently to the face and slowly move the device by sliding it
from the center of the face to the outer side.
Do not keep the heating head on the same area of skin, it is
necessary to move it around.
(Cause of problems with your skin or physical discomfort.)
Do not apply the device on the same area of skin for more than 10 seconds.
●
●
If you feel your skin tingling by micro current while using the device, press the
Level switch button and switch to "LOW." If you still feel your skin tingling, use the
device by adding more toner or other cosmetics.
6 After 3 minutes have elapsed, the device will automatically shut off.
(Auto shutoff function)
●
The finish sound (beep beep) will inform you.
7 After use, make sure to pull out the power adaptor from the electric outlet and the
main body. (Fig. 7)
●
To continue to use the next mode, do not disconnect the power adaptor.
8 Wipe off the moisturizing product on the heating head and the body of the device with a
tissue.
③T-zone
-10-
Advertisement
