Sealey SA141 Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear ear
instruction protection
manual
1. SAFETY

Follow all Health & Safety and general workshop rules, regulations and conditions when using the wrench.
‰
WARNING! Disconnect from air supply before changing accessories or servicing.

Maintain the wrench in good condition and replace any damaged or worn parts. Use genuine parts only. Unauthorised parts may be
dangerous and will invalidate the warranty.
‰
WARNING! Check correct air pressure is maintained and not exceeded. We recommend 90psi.

Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are secure.
Only use impact sockets which are specifi cally designed for use with an impact wrench.


Wear approved safety eye/face shield, ear defenders and hand protection.

Maintain correct balance and footing. Ensure that the floor is not slippery and wear non-slip shoes.

Keep children and non-essential persons away from the work area.
8
DO NOT use the wrench for a task that it is not designed to perform.
‰
WARNING! DO NOT use wrench if damaged or thought to be faulty (contact your Service Agent).
8
DO NOT use wrench unless you have been instructed in its use by a qualified person.
8
DO NOT carry the wrench by the air hose, or yank the hose from the air supply.
8
DO NOT operate the wrench if you are tired or under the influence of alcohol, drugs or intoxicating medication.

To avoid unintentional starting DO NOT carry the wrench with your finger on the trigger.
8
DO NOT direct air from the air hose at yourself or others.

When not in use, disconnect from the air supply and store in a safe, dry, childproof location.
‰
WARNING! – RISK OF HAND ARM VIBRATION INJURY
This tool may cause Hand Arm Vibration Syndrome if its use is not managed adequately.
This tool is subject to the vibration testing section of the Machinery Directive 2006/42/EC.
This tool is to be operated in accordance with these instructions.
Measured vibration emission value (a): 5.1m/s²
Uncertainty value (k): 1.0m/s²
Please note that the application of the tool to a sole specialist task may produce a different average vibration emission. We recommend
that a specifi c evaluation of the vibration emission is conducted prior to commencing with a specialist task.
A health and safety assessment by the user (or employer) will need to be carried out to determine the suitable duration of use for
each tool.
NB: Stated Vibration Emission values are type-test values and are intended to be typical.
Whilst in use, the actual value will vary considerably from and depend on many factors.
Such factors include; the operator, the task and the inserted tool or consumable.
NB: ensure that the length of leader hoses is suffi cient to allow unrestricted use, as this also helps to reduce vibration.
The state of maintenance of the tool itself is also an important factor, a poorly maintained tool will also increase the risk of Hand Arm
Vibration Syndrome.
1.1. HEALTH SURVEILLANCE
We recommend a programme of health surveillance to detect early symptoms of vibration injury so that management procedures can
be modifi ed accordingly.
1.2. PERSONAL PROTECTIVE EQUIPMENT
We are not aware of any personal protective equipment (PPE) that provides protection against vibration injury that may result from the
Uncontrolled use of this tool. We recommend a suffi cient supply of clothing (including gloves) to enable the operator to remain warm
and dry and maintain good blood circulation in fi ngers etc. Please note that the most effective protection is prevention, please refer to
the Correct Use and Maintenance section in these instructions. Guidance relating to the management of hand arm vibration can be
found on the HSC website www.hse.gov.uk - Hand-Arm Vibration at Work.
2. INTRODUCTION
Reduced torque impact wrench suitable for the removal of seized glow plugs on diesel engines. Features a 4-position air regulator
which provides limited torque settings to suit. One-handed operation for trigger and forward/reverse control. Soft grip reduces vibration,
chill effect and adds comfort. Handle exhaust helps to lower noise level during use. Includes fi ve deep impact sockets, extension bar
and universal joint. Supplied with foam insert and metal storage case.
© Jack Sealey Limited
1/4"SQ DRIVE AIR IMPACT WRENCH DIESEL
GLOW PLUG KIT
MODEL NO:
Wear eye Wear protective
protection gloves
Original Language Version
SA141
Wear a mask
SA141 Issue 3 (ALL) 17/07/23