Sealey SG115E Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instructions protection
1. SAFETY
WARNING! Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all
‰
instructions listed below may result in electric shock, fire and/or serious injury. Save all warning and instructions for future reference.
1.1. WORK AREA SAFETY
Keep work area clean and well lit. Cluttered or dark areas invite accidents.
9
DO NOT operate power tools in explosive atmospheres, such as in the presence of flammable materials, liquids, gases or dust. Power
8
tools create sparks which may ignite the dust or fumes.
Keep children and bystanders away whilst operating a power tool. Distractions can cause you to lose control.
9
Anyone entering the work area must wear personal protective equipment. Fragments of workpiece or of a broken accessory may fly
9
away and cause injury beyond immediate area of operation.
1.2. ELECTRICAL SAFETY
WARNING! It is the user's responsibility to check the following:
‰
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. If the lamp is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
Electrical safety information, it is important that the following information is read and understood.
1.2.1. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.2.2. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
WARNING! Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
‰
correct fuse - see fuse rating in these instructions.
DO NOT pull or carry the appliance by the power cable.
8
DO NOT pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a firm grip on the plug.
8
DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or
8
replaced immediately by a qualified electrician.
1.2.3. This product is fitted with a BS1363/A 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 3 pin plug. If in doubt contact a qualified electrician.
Class II products are wired with live (brown) and neutral (blue) only are marked with the Class II symbol;
A) Connect the BROWN live wire to the live terminal 'L'.
B) Connect the BLUE neutral wire to the neutral terminal 'N'.
C) After wiring, check that there are no bare wires and ensure that all wires have been correctly connected.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
DO NOT connect either wire to the earth terminal.
8
Sealey recommend that repairs are carried out by a qualified electrician.
Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adaptor
9
plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk
of electric shock.
Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of
9
electric shock if your body is earthed or grounded.
DO NOT expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
8
DO NOT abuse the cord. Never use the cord for carrying, pulling, or unplugging the power tool. Keep cord away from the heat, oil,
8
sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces
9
the risk of electric shock.
If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) * protected supply. Use of an RCD
9
reduces the risk of electric shock.
Hold the power tool by insulated gripping surfaces only, when performing an operation where the cutting accessory may contact
9
hidden wiring or its own cord. Cutting accessory contacting a "live" wire may make exposed metal parts of the power tool "live" and
could give the operator an electric shock.
© Jack Sealey Limited
ANGLE GRINDER Ø115MM, 230V 750W -
MODEL NO:
Wear protective Wear safety
gloves footwear
Original Language Version
SG115E, SG115EHV
Wear protective Wear ear
clothing protection
Wear a mask Wear respiratory
protection
(fumes)
Recommended fuse rating
13 Amp
SG115E, SG115EHV Issue 1 22/05/23