Mitsubishi Electric MELSERVO MR-D30 Installation Manual

General-Purpose AC Servo
Functional safety unit
Model
MR-D30
Installation Guide
Country/Region Sales office Tel
USA Mitsubishi Electric Automation, Inc. Tel
500 Corporate Woods Parkway, Vernon Hills, IL 60061, U.S.A.
Mitsubishi Electric Europe B.V. German Branch Tel
Germany
Mitsubishi-Electric-Platz 1, 40882 Ratingen, Germany
China Mitsubishi Electric Automation (China) Ltd. Tel
Mitsubishi Electric Automation Center, No.1386 Hongqiao Road, Shanghai, China
Korea Mitsubishi Electric Automation Korea Co., Ltd. Tel
7F to 9F, Gangseo Hangang Xi-tower A, 401, Yangcheon-ro, Gangseo-Gu, Seoul, Korea
Japan Mitsubishi Electric Corporation Tel
Tokyo Building, 2-7-3, Marunouchi, Chiyoda-ku, Tokyo 100-8310, Japan
HEAD OFFICE: TOKYO BLDG., 2-7-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
Specifications are subject to change without notice.
Compliance with the indicated global standards and regulations
is current as of the release date of this installation guide.
IB(NA)-0300227-J(2309)MEE
The original instructions for Europe are in English.
Copyright©2014 Mitsubishi Electric Corporation All Rights Reserved.
Contents of the package
Contents Quantity
MR-D30 functional safety unit 1
MR-D30 Installation Guide (this guide) 1
Rating plate Warning plate
The following shows an example of rating plate for An example of warning plate is shown below.
explanation of each item.
Serial number
Model
IP rating, Manual number
Capacity
Applicable power supply
Rated output
Regulation/legislation marking
Standard
An example of regulation/legislation marking is shown
Ambient temperature
KC number below.
Date of manufacture
Country of origin
1. About the manuals
To use the MR-D30 safely, read "MR-D30 Instruction Manual" carefully.
1.1 MELSERVO-J4 relevant manuals
This installation guide explains how to mount MR-J4 servo amplifiers. You can also check it with our website for free.
http://www.mitsubishielectric.com/fa/
If you have any questions about the operation or programming of the equipment described in this guide, contact your
local sales office.
In addition, when you mount a protective device, specific technical skills which are not detailed in the guide will be
required.
Servo amplifiers and drive units are written as servo amplifiers in this guide under certain circumstances, unless
otherwise stated.
1.2 Purpose of this guide
This installation guide explains the safe operation of MR-J4 servo amplifiers for engineers of machinery manufacturers
and machine operators. For detailed information of the products, refer to "MR-D30 Instruction Manual". This installation
guide does not explain how to operate equipment in which MR-D30 and MR-J4 servo amplifier are integrated.
1.3 Terms related to safety
(1) STO (Safe torque off)
Shuts off servo motor drive energy electronically based on an input signal from an external device (secondary-side
output shut-off). This corresponds to stop category 0 of IEC/EN 60204-1.
(2) SS1 (Safe stop 1)
Starts deceleration based on an input signal from an external device (EM2). After a specified time for the check of
stop, STO function will be activated (SS1). This corresponds to stop category 1 of IEC/EN 60204-1.
(3) SS2 (Safe stop 2)
Starts deceleration based on an input signal from an external device (EM2). After a specified time for the check of
stop, the SOS function will be activated (SS2). This corresponds to stop category 2 of IEC/EN 60204-1.
(4) SOS (Safe operating stop)
This is a function to monitor whether the servo motor stops within the prescribed range for the stop position. The
power is supplied to the servo motor.
(5) SLS (Safely-limited speed)
This is a function to observe whether the speed is within a regulated speed limit value. When the speed is over a
specified speed, energy will be shut off by STO.
(6) SSM (Safe speed monitor)
Outputs a safety output signal when the servo motor speed is within a regulated speed.
(7) SBC (Safe brake control)
Outputs a safety output signal for an external brake control.
(8) Status monitor (SM)
Outputs a signal for the safety observation function status. This function is not the one defined in IEC/EN 61800-5-
2. The function is an original function of the functional safety unit.
2. About safety
This chapter explains safety of users and machine operators. Please read the chapter carefully before mounting the
equipment. In this installation guide, the specific warnings and cautions levels are classified as follows.
WARNING
Indicates that incorrect handling may cause hazardous conditions, resulting in death or severe injury.
Indicates that incorrect handling may cause hazardous conditions, resulting in medium or slight injury
CAUTION
to personnel or may cause physical damage.
2.1 Professional engineer
Only professional engineers should mount this to MR-J4 servo amplifiers.
Here, professional engineers should meet all the conditions below.
(1) Persons who took a proper training of related work of electrical equipment or persons who can avoid risk based on
past experience.
(2) Persons who have read and familiarized himself/herself with this installation guide and operating manuals for the
protective devices (e.g. light curtain) connected to the safety control system.
2.2 Applications of the devices
MR-D30 has a control system whose configuration is possible to be for safety.
This product complies with the following standards.
EN ISO 13849-1:2015 Category 3 PL d and Category 4 PL e
IEC 61508 SIL 2 and SIL 3
EN IEC 62061:2021 maximum SIL 2 and maximum SIL 3
EN 61800-5-2
IEC/EN 61800-3/GB 12668.3/KN 61800-3 (KS C 9800-3)
An achieved safety level depends on external circuit, wiring conditions, parameter settings, sensor selections, and
mounting position on the machine.
A photoelectric and contact sensor such as light curtain, laser scanner, safety switch, sensor, and push button for
emergency stop can be used with programs. The power of an actuator mounted on the machine or system can be shut
off safely using switching output of the safety control system.
2.3 Correct use
If you need to get close to the moving parts of the machine for inspection or others, ensure
WARNING
safety by confirming the power off, etc. Otherwise, it may cause an accident.
MR-D30 complies with basic specifications concerning radiation electromagnetic immunity
J
CAUTION
and fulfills requirements of industrial uses. Therefore, MR-D30 is only for use in industrial
environment, not for general use.
: +1-847-478-2100 Use the MR-D30 within specifications. Refer to "MR-D30 Instruction Manual" for specifications such as voltage,
temperature, etc. Mitsubishi Electric Co. accepts no claims for liability if the equipment is used in any other way or if
: +49-2102-486-0
modifications are made to the device, even in the context of mounting and installation.
: +86-21-2322-3030
2.3.1 Peripheral device
The following are selected based on IEC/EN 61800-5-1, UL 61800-5-1, UL 508C, and CSA C22.2 No. 274.
: +82-2-6103-9474
: +81-3-3218-2111
(1) Motor overload and Over temperature protection
The overload protection of the servo motor does not include a thermal memory function, and is not speed
sensitive. The servo amplifier cannot detect overheating of the servo motor. The servo motors are protected by the
servo motor overheat protection function of the servo amplifiers (a protection characteristic based on 120 % of the
rated current). To provide the servo motor with overheat protection, use a magnetic contactor (electromagnetic
switch) with a thermal relay. Alternatively, install a thermal sensor or equivalent equipment near the rating plate of
the servo motor to check that the servo motor temperature is under 105 °C with sensing device. (Refer to Chapter
4)
2.3.2 Europe/UK compliance
The CE/UKCA marking proves the compliance of the servo product with the essential requirements specified in the
relevant EU Directives and UK Regulations, and this marking also applies to machines and equipment incorporating
servos.
(1) EMC requirement
The combination of MR-J4 servo amplifier and MR-D30 complies with EN/BS EN IEC 61800-3. As for I/O wires
(max. length 10 m) and encoder cables (max. length 50 m), use shielded wires and ground the shields.
Install an EMC filter and surge protector on the primary side. The following shows recommended products.
EMC filter: Soshin Electric HF3000A-UN series
Surge protector: Okaya Electric Industries RSPD-250-U4 series
MR-J4 Series are not intended to be used on a low-voltage network which supplies domestic premises;
electromagnetic interference is expected if used on such a network.
The installer shall provide a guide for Installation and use, including recommended mitigation devices. To avoid the
risk of crosstalk to signal cables, the installation instructions shall either recommend that the power interface cable
be segregated from signal cables.
(2) For Declaration of Conformity (DoC)
We declare that the servo amplifier with MR-D30 is in compliance with EC directives (Machinery directive
(2006/42/EC), EMC directive (2014/30/EU), Low-voltage directive (2014/35/EU), and RoHS directive (2011/65/EU,
(EU) 2015/863)) and applicable regulations of the UK. For the copy of Declaration of Conformity, contact your local
sales office.
2.3.3 USA/Canada compliance
The servo amplifiers on which MR-D30 is mounted are designed in compliance with UL 508C or UL 61800-5-1 for the
use in the United States. For the use in Canada, the servo amplifiers on which MR-D30 is mounted are designed in
compliance with CSA C22.2 No. 274.
(1) Installation
The minimum cabinet size is 150 % of each MR-J4 servo amplifier's volume including MR-D30. Also, design the
cabinet so that the ambient temperature in the cabinet is 55 ˚C or less. The servo amplifiers on which MR-D30 is
mounted must be installed in a metal cabinet. For environment, the units should be used in open type (UL 50) and
overvoltage category III or lower. MR-D30 and servo amplifier needs to be installed at or below pollution degree 2.
For connection, use only copper wires.
(2) Short-circuit current rating (SCCR)
Each servo amplifier on which MR-D30 is mounted has checked with a short-circuit test.
(3) Capacitor discharge
It takes 15 minutes for capacitor discharging of the servo amplifier on which MR-D30 is mounted. Do not touch the
unit and terminals immediately after power off.
(4) Branch circuit protection
For installation in United States, branch circuit protection must be provided, in accordance with the National
Electrical Code and any applicable local codes. For installation in Canada, branch circuit protection must be
provided, in accordance with the Canadian Electrical Code and any applicable provincial codes.
2.3.4 South Korea compliance
Products that bear the KC mark comply with the Radio Wave Law. Please note the following to use the product.
이 기기는 업무용 (A급) 전자파적합기기로서 판매자 또는 사용자는 이 점을 주의하시기 바라며, 가정외의지역에서
사용하는 것을 목적으로 합니다.
(The product is for business use (Class A) and meets the electromagnetic compatibility requirements. The seller and the
user must note the above point, and use the product in a place except for home.)
2.4 Safety observation function compatible unit
The safety observation function is executed by writing a parameter to MR-D30 in a system using an MR-J4 servo
amplifier, motion CPU and safety programmable controller in the following table. Set the parameters of MR-D30
correctly for a proper operation of the safety observation function. Protective functions such as the safety observation
function may not work due to an incorrect setting. Refer to "MR-D30 Instruction Manual" for the parameter setting
details.
(1) List of safety observation function compatible unit
Product name
MR-J4-_GF-RJ/MR-J4-_GF4-RJ
Servo amplifier MR-J4-_B-RJ/MR-J4-_B4-RJ/MR-J4-_B1-RJ/MR-J4-DU_B-RJ/MR-J4-DU_B4-RJ
MR-J4-_A-RJ/MR-J4-_A4-RJ/MR-J4-_A1-RJ/MR-J4-DU_A-RJ/MR-J4-DU_A4-RJ
Programmable controller (Note 1) R_SFCPU
Motion CPU module (Note 2) Q173DSCPU/Q172DSCPU
Note 1. For using the safety observation function through CC-Link IE Field
2. For using the safety observation function through SSCNET III/H
(2) List of safety observation function compatible unit version
(a) Servo amplifier and functional safety unit
1) MR-J4-_GF_-RJ
a) Safety observation function control by input device
MR-D30 Servo amplifier
Safety observation function
software version software version
STO/SS1/SBC/SLS/SSM/SOS/
A1 or later A3 or later (Note)
SS2/SM
Note. CC-Link IE Field Network Basic communication is not supported. While CC-Link IE Field Network Basic has been set, connecting
with the MR-D30 functional safety unit triggers [AL. 3E.8].
b) Safety observation function control by network
MR-D30 Servo amplifier
Safety observation function
software version software version
STO/SS1/SBC/SLS/SSM/SOS/
A2 or later A3 or later
SS2/SM
2) MR-J4-(DU)B_-RJ/MR-J4-(DU)A_-RJ
MR-D30 Servo amplifier
software version software version
A0 B3 or later
B3/B4
A1 or later
B5 or later
Note. The servo amplifiers manufactured in November, 2014 or later is supported.
(b) Programmable controller
Model
R_SFCPU
(c) Motion controller
Model
Q173DSCPU SW8DNC-SV22QJ/SW8DNC-SV13QJ
Q172DSCPU SW8DNC-SV22QL/SW8DNC-SV13QL
2.5 General cautions for safety protection and protective measures
POINT
Observe the cautions for safety protection and protective measures.
Observe the items in this section for proper use of MR-D30.
(1) When mounting, installing, and using the MR-D30, always observe standards and directives applicable in the
country.
(2) When using an MR-D30 in an EU member state, comply with the following directives.
Machinery directive 2006/42/EC
EMC directive 2014/30/EU
Low voltage directive 2014/35/EU
RoHS directive 2011/65/EU
Other laws/regulations of labor safety
(3) The manufacturer and owner of machines on which an MR-D30 is used should be familiarized with all the
applicable laws and regulations and should be responsible to observe them.
For Declaration of Conformity (DoC), our company declares that the servo amplifiers are in compliance with the
necessary requirements and standards (2006/42/EC, 2014/30/EU, 2014/35/EU and 2011/65/EU). You can obtain
the copy of Declaration of Conformity from our website.
(4) The contents of "MR-D30 Instruction Manual" must be observed.
(5) Tests should be performed by professional engineers, especially qualified and responsible personnel, and should
be recorded/documented for a third party to rebuild and confirm the tests.
(6) Based on IEC/EN 60204-1, connect to a power supply that has tolerance against instantaneous power failure of 20
ms or more.
2.6 Disposal
Disposal of unusable or irreparable devices should always occur in accordance with the applicable country-specific
waste disposal regulations.
2.7 Risk assessment
To ensure safety, users should decide all the risk assessments and residual risks in the entire machine equipment. A
company and/or individual who constructed the safety related system must take full responsibility for installation and
commissioning of the system. Additionally, when complying with a European machinery directive, the system must
acquire safety standards certification as a whole.
Perform all risk assessments and safe level certification to the machine or the system as a whole. It is recommended
that a Certification Body final safety certification of the system be used.
The following shows residual risks concerning the safety observation function of this product.
2.7.1 Common residual risks in each function
(1) At the shipment to end-users, check the settings of safety related components with programming tools and
monitored/displayed contents on display and record and save the setting data concerning the safety observation
function and the programming tools you used. Perform them using a check sheet, etc.
(2) The safety will not be ensured such as in assembling machine until installing, wiring, and adjustment are
completed properly. Install, wire, and adjust your system referring to installation guide for each unit.
(3) Only qualified personnel are authorized to install, start-up, repair or adjust the machines in which these
components are installed. Only trained engineers should install and operate the equipment. (ISO 13849-1:2015
Table F.1 No. 5)
(4) Separate the wiring for safety observation function from other signal wirings.
(ISO 13849-1:2015 Table F.1 No. 1)
(5) Protect the cables with appropriate ways (routing them in a cabinet, using a cable guard, etc.).
(6) We recommend using a switch, relay, sensor, etc. which comply with safety standards. When using a switch,
relay, sensor, etc. which do not comply with safety standards, perform a safety confirmation.
(7) Keep the required clearance/creepage distance depending on voltage you use.
(8) The time to a safety observation error depends on parameter settings.
2.7.2 Residual risks in each function
(1) Speed monitoring (SLS)
(a) Speed monitoring function guarantees the servo motor speed), but it does not guarantee the actual machine
safety speed. Set parameters so that the safe speed of the machine is the same as the safety speed of the
specified motor.
(b) Check if the speed of the monitored servo axis is the same as the actual speed by using a tachometer, etc.
Model
considering the speed includes an error caused by the command and encoder resolution.
(c) The defect of the mechanical section such as slid of shaft and wanting of a timing belt, etc. is not covered. Be
sure to eliminate the risk of mechanical section before operation.
(d) Speed monitoring error detection time is set to 1 ms. Error in shorter than this time are not detected.
(e) After speed is over the limit, safety observation error (shut-off signal off) does not occur during the speed error
detection time set by the parameter. Make sure that safety can be ensured during this period.
(2) Safe speed monitor (SSM)
When SSM is used as a restart trigger, perform it according to IEC/EN 60204-1.
(3) Safe brake control (SBC)
Servo motor with
Servo amplifier
This function guarantees only that power to mechanic break is properly supplied and abrasion of the brake cannot
functional safety
be detected. Check this function regularly that the mechanic brake can operate.
HG-KR_W0C
HG-SR_W0C MR-J4-_GF_-RJ
3. Conditions of use for the product
HG-JR_W0C
(1) MR-D30 complies with a safety standard, but this fact does not guarantee that MR-D30 will be free from any
malfunction or failure. The user of this product shall comply with any and all applicable safety standard, regulation
or law and take appropriate safety measures for the system in which the product is installed or used and shall take
the second or third safety measures other than the product. Our company is not liable for damages that could have
Servo motor with been prevented by compliance with any applicable safety standard, regulation or law.
Servo amplifier
functional safety
HG-KR_W0C
(2) Our company prohibits the use of Products with or in any application involving, and we shall not be liable for a
HG-SR_W0C MR-J4-_GF_-RJ
default, a liability for defect warranty, a quality assurance, negligence or other tort and a product liability in these
HG-JR_W0C
applications.
(a) Power plants
(b) Trains, railway systems, airplanes, airline operations, and other transportation systems
(c) Hospitals, medical care, dialysis and life support facilities or equipment
(d) Amusement equipment
(e) Incineration and fuel devices
(f) Handling of nuclear or hazardous materials or chemicals
(g) Mining and drilling
(h) Other applications where the level of risk to human life, health or property are elevated.
4. Block diagram and timing chart
(1) Function block diagram (for using input signal)
Servo motor with
Safety observation function Servo amplifier
functional safety This is an example of a combination with MR-J4-_B_-RJ.
STO/SS1/SBC/SLS/SSM/SM Not compatible MR-J4-_B_-RJ
STO/SS1/SBC/SLS/SSM/SM Not compatible MR-J4-_B_-RJ
MR-J4-_B_-RJ
HG-KR_W0C
STO/SS1/SBC/SLS/SSM/SOS/ MR-J4-_A_-RJ (Note)
HG-SR_W0C
SS2/SM MR-J4-DU_B_-RJ Power
HG-JR_W0C
MR-J4-DU_A_-RJ (Note)
Software version
07 or later
(Remove the short-circuit connector.)
Controller or
servo amplifier
OS Software version
Servo amplifier
05 or later
Input signal
Note 1. Safety switch, safety relay, etc.
2. The servo motor with functional safety is required to use the SS2/SOS functions.
(2) How to use the functions
To use the safety observation functions, combine MR-D30 with MR-J4. For how to use the functions, refer to "MR-
D30 Instruction Manual".
5. Maintenance and disposal
MR-D30 safety logic unit is equipped with LED displays to check errors for maintenance.
Please dispose this unit according to your local laws and regulations.
Changing the combination of MR-D30 and MR-J4 servo amplifier will trigger [AL. 7A.4 Functional safety unit combination
error (safety observation function)] and the safety observation function you set will not operate.
6. Functions and configuration
6.1 Summary
(1) Safety observation functions are available with your servo amplifier.
Mounting the functional safety unit to the servo amplifier enables you to use the safety observation functions such
as STO/SS1/SS2/SOS/SLS/SSM/SBC without depending on a controller.
(2) Drive safety compatible integrated motion controller
Safety communication with motion controllers is available by using MR-D30 with MR-J4-_B_-RJ. With this, the
wiring which was required can be reduced for the STO signal and encoder signal for safety observation.
(3) Drive safety integrated programmable controller
Safety communication with safety programmable controller is available by using MR-D30 with MR-J4-_GF_-RJ.
With this, the wiring which was required can be reduced for the STO signal and encoder signal for safety
observation.
6.2 Transportation and storage
CAUTION
When you keep or use it, please fulfill the following environment.
Ambient temperature
Ambient humidity
Vibration resistance
Pollution degree
IP rating
Altitude
Note. In regular transport packaging
6.3 Specifications
Output
Interface power supply
Safety performance
Safety observation
function
(IEC/EN 61800-5-2)
Safety observation
function
Compliance to global
standards
Structure (IP rating)
Mass
Note 1. This is the value applicable when all I/O signals are used. The current capacity can be decreased by reducing the number of I/O points.
2. Time from STO input off to energy shut off
3. To meet Category 4, PL e, SIL 3 for input signals, a diagnosis using test pulses is required.
4. To meet Category 4, PL e, SIL 3, using with a servo motor with functional safety is required.
5. To enable SS2 and SOS, using with a servo motor with functional safety is required.
6. For the achievable safety level, refer to the section of "Safety observation function (IEC/EN 61800-5-2)".
7. The scale measurement function of the semi closed loop system, linear servo system, direct drive servo system, and fully closed loop
system are not compatible with SLS, SSM, SS2, and SOS. The MR-J4-_GF_-RJ with software version B0 or later used in a direct drive
servo system is compatible with SLS and SSM.
Servo amplifier Servo motor (Note 2)
MCCB MC
L1
U U
V V
L2
M
W W
L3
L11
Control circuit Gate circuit
L21 24 V DC
power supply
B1
Electromagnetic
Not used
B
brake
B2
RA
SSCNETIII/H
Encoder
SSCNETIII/H
Control
USB Sensing device
Parameter setting
CN9 CN7
CN90 CN70
Functional safety unit
Safety observation function
processing part 1 Output signal
(Note 1)
(Note 1)
Safety observation function
processing part 2
Transport the products correctly according to their mass.
Stacking in excess of the limited number of product packages is not allowed.
Install the equipment in a load-bearing place in accordance with "MR-D30 Instruction
Manual".
Do not put excessive load on the machine.
Item Environment
Operation [°C] 0 to 55 Class 3K3 (IEC/EN 60721-3-3)
Transportation
[°C] -20 to 65 Class 2K12 (IEC/EN 60721-3-2)
(Note)
Storage (Note) [°C] -20 to 65 Class 1K4 (IEC/EN 60721-3-1)
Operation, transportation,
5 %RH to 90 %RH
storage
10 Hz to 57 Hz with amplitude of 0.075 mm
Test condition
57 Hz to 150 Hz with constant acceleration of 9.8 m/s 2 to IEC/EN 61800-5-1 (Test Fc of IEC
60068-2-6)
Operation 5.9 m/s 2 (X, Y, Z axes)
Transportation
Class 2M3 (IEC/EN 60721-3-2)
(Note)
Storage Class 1M2 (IEC/EN 60721-3-2)
2
Mounted on a servo amplifier: IP20 (IEC/EN 60529)
MR-D30 (single): IP00 (IEC/EN 60529)
Open type (UL 50)
Operation, storage 2000 m or less
Transportation 10000 m or less
Model MR-D30
Rated voltage 24 V DC
Rated current [A] 0.3
Voltage 24 V DC ± 10 %
Power supply
[A] 0.8 (Note 1)
capacity
EN ISO 13849-1:2015 Category 4, PL e and Category 3, PL d
IEC 61508 SIL 2 and SIL 3
Standards certified by CB
EN IEC 62061:2021 maximum SIL 2 and maximum SIL 3
EN 61800-5-2
Mean time to dangerous
MTTFd ≥ 100 [years] (313a)
failure (MTTFd)
Diagnostic coverage (DC) DC = High, 97.6 [%]
Probability of dangerous
PFH = 6.57 × 10 -9 [1/h]
failures per hour (PFH)
Mission time (T ) T = 20 [years]
M M
Using input device: 15 ms or less
Response performance
Using a drive Safety integrated motion controller: 60 ms or less
(Note 2)
Using drive safety integrated programmable controller: 65 ms or less
Speed observation resolution Depends on a command resolution (22 bit position command: 0.1 r/min or less)
Position observation
1/32 rev
resolution
Safety position data resolution 32 pulses/rev (5 bits)
Input device 6 points × 2 systems (source/sink)
Source: 3 points × 2 systems and 1 point × 1 system
Output device
Sink: 1 point × 1 system
Safe torque off (STO) Category 4, PL e, SIL 3 (Note 3)/Category 3, PL d, SIL 2
Safe stop 1 (SS1) Category 4, PL e, SIL 3 (Note 3)/Category 3, PL d, SIL 2
Safely-limited speed (SLS)
Category 4, PL e, SIL 3 (Note 3, 4)/Category 3, PL d, SIL 2
(Note 7)
Safe speed monitor (SSM)
Category 4, PL e, SIL 3 (Note 3, 4)/Category 3, PL d, SIL 2
(Note 7)
Safe brake control (SBC) Category 4, PL e, SIL 3 (Note 3)/Category 3, PL d, SIL 2
Safe operating stop (SOS)
Category 4, PL e, SIL 3 (Note 3)/Category 3, PL d, SIL 2
(Note 5, 7)
Safe stop 2 (SS2) (Note 5, 7) Category 4, PL e, SIL 3 (Note 3)/Category 3, PL d, SIL 2
Status monitor (STO/SOS) Category 4, PL e, SIL 3/Category 3, PL d, SIL 2 (Note 6)
EMC: EN 61800-3
CE marking
MD: EN ISO 13849-1:2015, EN 61800-5-2, EN IEC 62061:2021
Natural cooling, open (mounted on a servo amplifier: IP20, MR-D30 (single): IP00)
[g] 150