Page 3
Dimensions: Width: Height: Depth: Including TV stand 874mm 580mm 238mm TV set only 874mm 534mm 52mm Mass: Including TV stand 14.0kg TV set only 11.5kg Design and Specifications are subject to change without notice. Mass and dimensions shown are approximate. This equipment complies with the EMC standards listed below: EN55013, EN61000-3-2, EN61000-3-3, EN55020, EN55022, EN55024 Warning...
CONTENTS SAFETY PRECAUTIONS ........... 5 HOTEL MODE ............18 GENERAL GUIDE LINES........5 DATA COPY BY SD CARD........19 TOUCH – CURRENT CHECK....... 5 DATA COPY FROM TV SET TO SD CARD ..... 20 PREVENTION OF ELECTROSTATIC DISCHARGE DATA COPY FROM SD CARD TO TV SET ..... 21 (ESD) TO ELECTROSTATICALLY SENSITIVE (ES) OPTION BYTES DESCRIPTION ......
Safety Precautions General Guide Lines When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
Prevention of Electrostatic Discharge (ESD) to Electrostatically Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor "chip"...
About lead free solder (PbF) Note: Lead is listed as (Pb) in the periodic table of elements. In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder. The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu). That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available.
Service Hints How to remove the backcover Remove the 4 fixing screws, the 1 fixing screw and WIFI DONGLE. (see Fig.5) SCREWS (1) THTD030J /1pcs/ (4) XYN4+F25FJK /4pcs/ Fig.5 Remove the 27 fixing screws, 4 caps and the backcover. (see Fig.6) SCREWS (1) THTD030J /14pcs/ (2) THEC1509 /13pcs/...
How to SELF CHECK: While pressing [VOLUME ( - )] button on the main unit, press the STATUS button on the remote control for more than 3 seconds. TV will be forced to the factory shipment setting after this SELF CHECK. Model and Keys: Keys Model No. One-to-One CI PLUS DTCP-IP Widevine Netflix (for USB Rec.) TX-L37ETW5...
Self-check is used to automatically check the bus lines and hexadecimal code of the TV set. To enter Self-Check mode, keep pressing the down (-/v) button on the TV set and press the STATUS button on the remote control. To exit Self Check, switch off the TV set at the power button. TX-L37ETW5 37FHD Panasonic 2012LCD Self Check Complete...
Power LED blinking timing chart Subject Information of LED Flashing timing chart. Contents When abnormality has occurred the unit, the protection circuit operates and reset to the stand by mode. At this time, the defective block can be identified by number of blinking of the Power LED on the front panel of the unit. Blinking Blinking timing Contents...
Service Mode Function MPU controls the functions switching for each IICs through IIC bus in this chassis. The following setting and adjustment can be adjusted by remote control in Service Menu How to enter SERVICE While pressing (-/v) button on the TV unit, press on the remote control for 3 times within 2 seconds.
SERVICE SERVICE Peaks SOFT 1.210 OPTION 1 14 Key Command ADJUST Peaks EEP 01.01.0033 OPTION 2 S e r v i c e 1 WB-ADJ LSI PACKAGE 2.41d OPTION 3 OPTION LSI DATA 1.00.07 OPTION 4 10 Press the 3/4 button to change the adjustment values or function. SRV-TOOL STBY SOFT 1.03.02...
Service Tool Mode How to access Select [SRV-TOOL] in Service Mode. Press [OK] button on the remote control. SRV-TOOL Display of TD2Microcode version TD2Microcode:005a0910 Flash ROOM: AD – F1 Display of Flash ROM maker code POWER ON TIME/COUNT PTCT:00.00.00.00.00 Time 00051:30 On/Off 0000042 Display of SOS History Press [MUTE] button (3sec)
Hotel Mode 1. Purpose Restrict a function for hotels. 2. Access command to the Hotel mode setup menu. In order to display the Hotel mode setup menu, please enter the following command (within 2 second). [TV] : Vol.[Down] + [REMOTE] : AV (3 times) Then, the Hotel mode setup menu is displayed.
Data Copy by SD Card Purpose a) Board replacement (Copy the data when exchanging A-board): When exchanging A-board, the data in original A-board can be copied to SD card and then copy to new A-board. Following data can be copied. (Before exchanging) User setting data Copy to SD card...
Data Copy from TV set to SD Card Turn on the TV set. Insert SD card with a startup file (pwd file) to SD slot. On-screen Display will be appeared according to the startup file automatically. Input a following password for (a) or (b) by using remote control. (a) For Board replacement: 2770 (b) For Hotel: 4850 Data will be copied from TV set to SD card.
Data Copy from SD Card to TV set Turn on the TV set. Insert SD card with Data to SD slot. On-screen Display will be appeared according to the Data folder automatically. Input a following password for (a) or (b) by using remote control. (a) For Board replacement: 2771 (b) For Hotel: 4851 Data will be copied from SD card to TV set.
Option Bytes Description OPTION1 TEXT Ch Refresh ON (1) / OFF (0) ID-1 ON (1) / OFF (0) Macrovision Auto-judge ON (1) / OFF (0) Surround enable low bit ON (1) / OFF (0) Surround enable high bit ON (1) / OFF (0) Enable HDMI force reset ON (1) / OFF (0) TINT_Component_HDMI...
Adjustment Method Sub-Contrast/White Balance Adjustment Instrument Name Connect to Remarks Remote controller Correlation can be also taken by LCD WB meter (Minolta CA-210 or equivalent) CS-1000A or equivalent Comunication jig Computer for external control Procedure Remarks Let the panel standfor more than 3 hours at more than 20 C.
Parts Location NOTE: The numbers on the exploded view below refer to the exploded view section of the Replacement Parts List. TMK0EA319 TMK0EA323 TMK0EA159 TMK0EA328...
Page 29
Parts Location NOTE: The numbers on the exploded view below refer to the exploded view section of the Replacement Parts List.
Replacement Parts List Important Safety Notice Components Identified by mark have special characteristics important for safety. * When replacing any of these components, use only manufacturers specified parts. In case of ordering these spare parts, please always add the complete Model-Type number to your order. RTL (Retention Time Limited) Note: The marking (RTL) indicates that the Retention Time is Limited for this item.
Page 31
Cct Ref Parts Number Description Cct Ref Parts Number Description IC5440 C0DBAYY01283 STEP DOWN CONVERTER D6852 B0ECKP000002 DIODE IC5720 C0DBGFD00102 REGULATOR D6853 B0JCME000093 DIODE IC5780 C0DBAYY01300 REGULATOR D6854 B0BC4R700007 ZENER DIODE IC6851 C1AB00003807 LNB SUPPLY AND CONTROL D6856 B0BC4R700007 ZENER DIODE IC7201 C0DBBYY00051 PFC CONTROL IC...
Schematic Diagrams IMPORTANT SAFETY NOTICE Components identified by mark have special characteristics important for safety. When replacing any of these components, use only manufacturers' specified parts. NOTE RESISTOR All resistors are carbon ¼W resistor, unless marked otherwise. Unit of resistance is OHM () (k=1,000, M=1,000,000) CAPACITORS All capacitors are ceramic 50V unless marked otherwise.
Page 72
P-BOARD TNPA5583 - TOP SW3750 SW3755 SW3756 SW3757 SW3758 SW3754 S W 3 7 5 0 S W 3 7 5 5 S W 3 7 5 6 S W 3 7 5 7 S W 3 7 5 8 S W 3 7 5 4 POWER VOL.DN...
Page 73
P-BOARD TNPA5583 - BOTTOM T P 3 7 5 0 SW3754 SW3758 SW3757 SW3756 SW3755 SW3750 C3750 C3751 非充電 S W 3 7 5 8 S W 3 7 5 7 S W 3 7 5 4 S W 3 7 5 5 S W 3 7 5 0 S W 3 7 5 6 R3758...
Page 74
FR-BOARD TNPA5587 - TOP C9332 R9085 C9331 TC04 T C 0 4 C9330 R9258 I C 9 1 0 0 R9080 R9260 R9259 R9257 R9256 R9008 R9005 R9015 R9013 R9011 R9009 R9007 R9006 R9004 R9014 R9012 R9010 R9271 C9252 2 0 8 R9270 R9087 TD10006...
Page 75
K-BOARD TNPA5604 - TOP C R N O . 2 S U F F I X . R2803 R2809 D2803 R2804 R2810 C2803 R2805 C2805 R2800 D2801 SN2800 C2809 D2805 C2802 R2807 R2808 C2804 C2807 R2806 D2804 T N P A 5 6 0 4 K 1 0 D2802 R M 8 0 0...
Need help?
Do you have a question about the TX-L37ETW5 and is the answer not in the manual?
Questions and answers