Table of Contents
Advertisement
Quick Links
DATA SHEET | MSDS | OPERATIONAL MANUAL
Pumps, Pumping Systems and Ancillaries
NEWTON TAS250
Ground & Surface Water Pump
Rev 1.0 - 01 June 2023
INTRODUCTION
Congratulations on your purchase of this pump product. All Newton pump products are developed with the help of the latest
technologies and manufactured with the most advanced electrical/motor parts.
Please check the following points upon receipt of your pump:
1.
The pump is the model that you ordered?
2.
Has any damage been caused during delivery?
3.
Are the pipe/valve ancillary parts you asked for included as requested?
IMPORTANT - This manual has been produced for the specific use of the Newton TAS250 pump and should be the main
reference document for the installation and safe use of the pumps. Please also familiarise yourself with the manual included in
the packaging. With manual versions of the pumps, it is imperative that the installation manual of the control panel or pump
controller is read in conjuction with this manual.
SPECIFICATIONS
Output
Discharge
Model
(W)
BSP
TAS250
250
1 1/2"
Check the nameplate for your pump's specification as the table above. Be careful not to exceed the given specifications in the use
of your pump.
LIMITATIONS
The Newton TAS250 series pumps are suitable to pump clean and dirty water with suspended soft solids of a maximum of 5mm.
Newton TAS250 Pump can be used for both permanent and temporary installation. They are not suitable for the pumping of
effluent or sewage. Do not let the pump run dry. The pump cannot be used for sea water and inflammable, corrosive, explosive or
dangerous liquids.
DANGER: Keep the equipment out of the reach of children
DANGER: Failure to follow the directions given could cause serious risk to individuals or property
WARNING: Failure to follow an instruction may damage the pump and/or the system
T: +44 (0)1732 360 095 W: www.newtonwaterproofing.co.uk E: tech@newtonwaterproofing.co.uk
Rated
Head (M)
Flow (LPM)
4
220
© Newton Waterproofing Systems
(a trading name of John Newton & Co. Ltd.)
Newton House, 17-20 Sovereign Way, Tonbridge, Kent, TN9 1RH
Maximum
Head (M)
Flow (LPM)
7.5
270
®
PRODUCT CODE - TAS250
Dimension
Weight
LxWxH (mm)
kg
190x140x360
11
Advertisement
Table of Contents
Related Manuals for Newton Waterproofing TAS250
Summary of Contents for Newton Waterproofing TAS250
- Page 1 LIMITATIONS The Newton TAS250 series pumps are suitable to pump clean and dirty water with suspended soft solids of a maximum of 5mm. Newton TAS250 Pump can be used for both permanent and temporary installation. They are not suitable for the pumping of effluent or sewage.
- Page 2 Electric Supply: The Newton TAS250 requires a single phase 230V AC power supply. It is advisable that all pumps are connected to their own individual power supply directly from the consumer board so that each of the pumps does not share a consumer board supply with the other pump or with any other electrical circuit or device.
- Page 3 Newton Waterproofing Systems shall possess the sole right to determine whether to repair or replace defective equipment, parts or components. PUMPS: Newton TAS250 is supplied with a 1-year manufacturers warranty from the proven date of installation or the date of purchase if this cannot be verified.
- Page 4 NEWTON TAS250 Ground & Surface Water Pump © Newton Waterproofing Systems (a trading name of John Newton & Co. Ltd.) Newton House, 17-20 Sovereign Way, Tonbridge, Kent, TN9 1RH T: +44 (0)1732 360 095 W: www.newtonwaterproofing.co.uk E: tech@newtonwaterproofing.co.uk...
Need help?
Do you have a question about the TAS250 and is the answer not in the manual?
Questions and answers