Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Shark Cordless Detect Pro Vacuum
Summary of Contents for Shark Cordless Detect Pro Vacuum
- Page 1 Shark Cordless ® Detect Pro Vacuum IW1000 Series IW3000 Series OWNER’S GUIDE...
-
Page 2: Table Of Contents
GUARANTEE, SIMPLY REGISTER YOUR PURCHASE Assembling your Shark® Detect Pro Vacuum Cleaner � � � � � � � � � � � � � � � � � � � 6 Using Your Anti-Odour Technology (IW3000 Series Only) � � � � � � � � � � � � � � 8 sharkclean.co.uk/register-guarantee... -
Page 3: Important Safety Instructions
If a part is damaged, is restricted. If the air paths or the motorised as indicated in this manual. 41. For IW3000 Series use only Shark battery discontinue use� floor nozzle become blocked, turn the DO NOT... - Page 4 AUTO-EMPTY ASSEMBLY (IW3000 SERIES) NON-AUTO-EMPTY ASSEMBLY (IW1000 SERIES) 1. Slide the Wand onto the neck of the Floor 4. Place the dock on the floor near a wall 1. Slide the Wand onto the neck of the Floor For proper operation, ensure all components Nozzle until it clicks into place�...
-
Page 5: Adjusting The Anti-Odour Technology Intensity
ANTI-ODOUR TECHNOLOGY (IW3000 SERIES) ANTI-ODOUR TECHNOLOGY (IW3000 SERIES) ADJUSTING THE ANTI-ODOUR TECHNOLOGY INTENSITY ODOUR CARTRIDGE REPLACEMENT 1. REMOVE ODOUR DIAL 2. REMOVE OLD ODOUR FROM THE AUTO-EMPTY DOCK CARTRIDGE ANTI-ODOUR TECHNOLOGY DIAL Flip up the handle and rotate the dial clockwise Rotate the cartridge counterclockwise in until the two arrows are aligned�... -
Page 6: Charging Your Li-Ion Battery
NOTE: When the unit is docked properly, the charging lights on the battery will blink, indicating that charging has begun� NOTE: The Shark battery, like all lithium-ion batteries, will naturally decrease in capacity over time from the 100% capacity of NOTE: The main unit comes with a partial charge�... -
Page 7: Battery Removal
USING YOUR VACUUM BATTERY REMOVAL REMOVING THE BATTERY CONTROLS AND CLEANING MODES POWER UPRIGHT BATTERY When upright, the nozzle will lock to allow Press the button on the UI Screen to for freestanding storage when the hand vac turn on power� To turn off power, press To remove the battery from the hand vacuum, is detached�... - Page 8 USING YOUR VACUUM USING YOUR VACUUM USING THE AUTO-EMPTY DOCK (IW3000 SERIES) ABOVE-FLOOR WITH WAND ABOVE-FLOOR WITH HAND VACUUM Detach the hand vacuum to clean above- To detach the floor nozzle from the wand, floor areas� Press the front latch release step on the nozzle while pressing the button on the hand vac where it meets the nozzle release button at the bottom of...
-
Page 9: Maintaining Your Vacuum Cleaner
MAINTAINING YOUR VACUUM MAINTAINING YOUR VACUUM EMPTYING THE DOCK DUST BIN (IW3000 SERIES) CLEANING THE DUST CUP AND FILTER The dock dust bin holds up to 30 days’ worth To empty the bin, hold it over the bin and With the dust cup open and the power off, To deep-clean the dust cup, slide the release of dust and debris�... -
Page 10: Cleaning The Auto Empty Dock Filter (Iw3000 Series Only)
MAINTAINING YOUR VACUUM MAINTAINING YOUR VACUUM CLEANING THE SENSORS CLEANING THE AUTO-EMPTY DOCK FILTER (IW3000 SERIES) Make sure to clean the Detect sensors Fig. 1 regularly, as hair and other debris may build up and obstruct them� If the sensors are partially obstructed, Clean Sense Detect mode will not function as expected�... -
Page 11: Checking For Blockages In The Vacuum
MAINTAINING YOUR VACUUM MAINTAINING YOUR VACUUM CHECKING FOR BLOCKAGES IN THE VACUUM TROUBLESHOOTING If you run over a hard or sharp object or notice a noise change while vacuuming, check for blockages or objects caught in the brushroll� WARNING: To reduce the risk of shock and unintended operation, turn off power and remove the battery before servicing. -
Page 12: Additional Accessories Available
What happens when my guarantee runs out? Shark does not design products to last for a limited time� We do appreciate that there may be a desire for our customers to want to repair their vacuum cleaners after the guarantee has lapsed� In this case please contact our Freephone customer service help line and ask about our out of guarantee programme, on 0800 862 0453�... -
Page 13: Battery Guarantee
Shark® Instructions supplied with your machine� 3� Use of the battery for anything other than powering the Shark® vacuum cleaner with which it was supplied� 4� Use of parts not assembled or installed in accordance with the operating instructions�... - Page 14 Illustrations may differ from actual product. We are constantly striving to improve our products; therefore the specifications contained herein are subject to change without notice. @sharkcleanuk © 2023 SharkNinja Operating LLC. FLOOR DETECT and SHARK are registered trademarks of SharkNinja Operating LLC in the United Kingdom.. @sharkcleanuk IW1000UK�IW3000UK�IB�MP�230905�Mv1...
Need help?
Do you have a question about the Cordless Detect Pro Vacuum and is the answer not in the manual?
Questions and answers
The vacuum quit running and the white light is on o the lower left side of the handle. What does this mean?
When vacuum is on high power it makes a loud squealing noise. have tried cleaning everything but does not make a difference
Need access to clean where roller is as it is dirty
To access the roller for cleaning on the Shark Cordless Detect Pro Vacuum, follow these steps:
1. Turn off the power and remove the battery to prevent unintended operation.
2. Press the brushroll release button.
3. Slide the brushroll out of the nozzle.
4. Clean the brushroll using only water if needed and let it air dry completely for at least 24 hours.
5. Once dry, reinstall the brushroll into the nozzle until it clicks into place.
This answer is automatically generated
How do I clean this section..little dust cup located on the bottom left.
To clean the dust cup on the Shark Cordless Detect Pro Vacuum:
1. Turn off the power.
2. Hold the hand vacuum over a bin.
3. Press the release button to open the dust cup lid.
4. Allow the debris to release into the bin.
Important: Do not use soap when cleaning the filters—use water only. Ensure all filters are installed before using the vacuum.
This answer is automatically generated