GIGABYTE M27Q - Gaming Monitor Manual

INTRODUCTION

Unpacking

1. Open the upper cover of the packaging box. Then observe the unpacking label attached on the inner cover.
2. Making sure the box is in the correct orientation, carefully lay the box on the stable surface.
   
3. Open the inner cover.
   
4. Grab the EPS foam assembly (through the openings) to pull it out of the box.
   
5. Remove the items from the upper EPS foam.
   
6. Remove the upper EPS foam. Then you can remove the monitor from the lower EPS foam.
   

Package Contents

The following items come with your packaging box. If any of them is missing, please contact your local dealer.

Note: Please keep the packaging box and packing materials for future transportation of the monitor.

Product Overview

Front View

1. Power LED

Rear View

6. DisplayPort
7. USB Type-C port
8. USB upstream port
9. USB 3.0 ports (x2)
10. DC IN jack

GETTING STARTED

Installing the Monitor Base

1. Place the monitor on the lower EPS foam, with the screen facing down.
2. Align the monitor base with the standoff underneath the stand. Then attach the base onto the stand.
   
3. Lift the screw ring and turn it clockwise to secure the monitor base in place.
   
4. Lift the monitor to an upright position and place it on a table.
5. Remove the small block of EPS foam located in between the rear of the screen and the stand. Then remove the safety plate from its slot.
   Note: By removing the safety plate, you can now adjust the screen to the desired height.
   

Adjusting the Viewing Angle

Note: Hold the monitor base so that the screen does not topple when you make the adjustment.

Adjusting the Tilt Angle
Tilt the screen forward or backward to the desired viewing angle (5˚ to 20˚).

Adjusting the Screen Height
Lower or raise the screen to the desired height (0 to 130mm).

Installing a Wall-Mount Bracket (Optional)

Use only the 100 x 100 mm wall mount kit recommended by the manufacturer.

1. Place the monitor on the lower EPS foam, with the screen facing down.
2. Remove the screws securing the stand to the monitor.
   
3. Remove the stand.
   
4. Attach the mounting bracket to the mounting holes at the rear of the monitor. Then use the screws to secure the bracket in place.
   Note: To mount the monitor on the wall, refer to the installation guide that is included in the wall-mount bracket kit.
   

Making Connections

1. Headphone cable
2. HDMI cable
3. DisplayPort cable
4. USB Type-C cable

5. USB (A-Male to B-Male) cable
6. USB cable
7. Power adapter and power cable

USING THE DEVICE

Turning the Power On/Off

Power On

1. Connect the power cable to the power adapter.
2. Connect the power adapter to the DC IN jack at the rear of the monitor.
3. Connect the power cable to a power outlet.
4. Press the Control button to turn on the monitor. The Power LED will light in white, indicating the monitor is ready to use.

Note: If no signal, the monitor will show No Signal notification for a while. Then, the monitor will go to power saving mode and the Power LED lights white and starts blinking with a period of one second.

Power Off
Press the Control button for 2 seconds to turn off the monitor. Note: When the Main menu appears on the screen, you can also turn off the monitor by moving the Control button down .

User Comfort Recommendations

The following are some tips for comfortable viewing of your monitor:

• Optimal viewing distances for monitors range from approximately 510 mm to 760 mm (20" to 30").
• A general guideline is to position the monitor such that the top of the screen is at or slightly below your eye-height when you are comfortably seated.
• Use adequate lighting for the type of work you are performing.
• Take regular and frequent breaks (at least for 10 minutes) every halfhour.
• Be sure to periodically look away from your monitor screen and focus on a far object for at least 20 seconds during the breaks.
• Eye exercise can help reduce eye strain. Repeat these exercises frequently:

1. look up and down
2. slowly roll your eye
3. move your eyes diagonally.

Selecting the Input Source

1. Move the Control button right () to enter the Input menu.
2. Move the Control button up/ down () to select the desired input source. Then press the Control button to confirm.

OPERATIONS

Quick Menu

Hot Key
By default, the Control button has been assigned with the specific function.
Note: To change the preset hot key function, refer to the "Quick Switch" section.
To access the hot key function, do the following:

• Move the Control button up () to enter the Black Equalizer menu.
  Move the Control button up/down () to adjust the setting and press the Control button to confirm.
  
• Move the Control button down () to enter the Picture Mode menu.
  Move the Control button up/down () to select the desired option and press the Control button to confirm.
  
• Move the Control button left () to enter the Volume menu. Move the Control button up/down () to adjust the headphone volume level and press the Control button to confirm.
  
• Move the Control button right () to enter the the Input menu.
  Refer to the "Selecting the Input Source" section.
  Note: To close the menu, move the Control button left ( ).

Function Key Guide

Press the Control button to display the Main menu.

Then use the Control button to select the desired function and configure the related settings.

KVM
When the Main menu appears on the screen, move the Control button left () to enter the KVM menu.

• KVM Switch: Switch the input source that has been assigned to USB-B or Type-C connection in the KVM Wizard settings.
  When there are several input signals connected to the device, a message box will appear on the screen once the system detected USB Type-C input signal.
  To switch to USB Type-C input source, simply press the KVM button or the Control button.
  However, when there is no input signal from currently selected input source, the system will return to the previous connected input source.
  Note: This option will be disabled if the KVM button function is disabled (KVM OFF).
  
• KVM Wizard: Configure the KVM related settings.
  Set the input source to be bound with USB Type-B connection first, and then following with USB Type-C connection.
  
  Note: If you set the USB-B Display setting to TYPE-C, the TYPE-C Display menu option will automatically be disabled. You will then see the KVM status in the KVM Wizard page as below.
  
• KVM ON/OFF: Enable/Disable the KVM button function.
  √ Select ON to enable the KVM button function. Once the system detected USB Type-C input signal, a message box will appear on the screen.
  
  Press the KVM button or the Control button to switch to USB Type-C input source.
  Note: When the KVM button function is enabled, the KVM ON will be displayed on the left panel.
  √ Select OFF to disable the KVM button function.
  Note: When the KVM button function is disabled, the KVM OFF will be displayed on the left panel.
• KVM Reset: Restore the KVM default settings.
  √ HDMI 1 input source is bound with USB Type-B connection.
  √ USB Type-C input source is bound with USB Type-C connection.
  √ The KVM ON/OFF function is set to ON.

Game Assist
When the Main menu appears on the screen, move the Control button right () to enter the Game Assist menu.

• Game Info: Configure the FPS (First Person Shooting) game related settings.
  √ Select Gaming Timer to select countdown timer mode. To disable this function, set the setting to OFF.
  √ Select Gaming Counter or Refresh Rate to enable/disable the gaming counter or real-time refresh rate setting.
  √ Select Info Location to specify the location of the information to be shown on the screen.
  
• Crosshair: Select the desired crosshair type to suit your gaming environment. It makes aiming much easier.
• Dashboard: Configure the dashboard settings.
  
  √ ON: Enable the function. Then select the desired option(s) to be shown on the screen.
  √ OFF: Disable the function.
  √ Dashboard Location: Specify the location of the Dashboard information to be shown on the screen. Once the Dashboard configuration is complete, it will transfer the system data to the SOC through the USB port and display the value of the selected function(s) on the screen.
  Note: Make sure the USB cable is properly connected to the USB upstream port of the monitor and the USB port of your computer.
  
• Display Alignment: When the function is enabled, it displays the alignment lines on the four sides of the screen, providing handy tool for you to line up multiple monitors perfectly.

Configure the Device Settings

When the Main menu appears on the screen, move the Control button up () to enter the Settings menu.
Note: Use the Control button to navigate through the menu and make adjustments.

Gaming
Configure the game related settings.

Picture
Configure the image related settings.

Select the one of the preset picture mode.

• Standard: For editing documents or browsing websites.
• FPS: For playing FPS (First Person Shooting) games.
• RTS/RPG: For playing RTS (Real-Time Strategy) or RPG (Role-Playing Game) games.
• Movie: For watching movies.
• Reader: For viewing documents.
• sRGB: For viewing photos and graphics on the computer.
• Custom 1: Customized picture mode settings.
• Custom 2: Customized picture mode settings.
• Custom 3: Customized picture mode settings.

Then you can configure the following image settings.

Display
Configure the display screen related settings.

PIP/PBP
Configure the multi-picture related settings.

Note: PIP/PBP is not compatible with HDR and AMD FreeSync Premium functions.

System
Configure the system related settings.

Item	Description
Audio	Configure the audio settings. Volume: Adjust the volume level. Mute: Enable/Disable the mute function.
OSD Settings	Configure the on-screen display (OSD) menu related settings. Display Time: Set the length of time the OSD menu remains on the screen. OSD Transparency: Adjust the OSD menu transparency. OSD Lock: When this function is enabled, no OSD adjustment is allowed. Note: To disable the OSD lock function, press the Control key. When the message appears on the screen, select Yes to confirm.
Quick Switch	Assign the function of the hot keys. Available options: Aim Stabilizer, Black Equalizer, Low Blue Light, Volume, Input, Contrast, Brightness, and Picture Mode. The default setting of the hot keys as below: Up : Black Equalizer Down : Picture Mode Right : Input Left : Volume
Other Settings	Resolution Notice: When this function is enabled, the recommended resolution message will appear on the screen when the monitor switches to another input source. Input Auto Switch: When this function is enabled, it automatically switches to an available input source. Auto Power OFF: When this function is enabled, the monitor will automatically turn off after a certain amount of time. DisplayPort Ver.: Set the DisplayPort version to 1.1 or 1.2+HDR. Note: To enable the HDR effect for the DP port, you may need to set the DP1.2 and enable the 10-bit color output in your graphics card. Make sure to configure this option based on the DisplayPort version supported by your graphics card.

Language
Select an available language for the OSD menu.

Save Settings
Set the personalized OSD configurations for Setting1, Setting2, or Setting3.

Reset All
Restore the monitor to its factory default settings.

Specifications

Note: Specifications subject to change without notice.

Supported Timing List

Timing List	HDMI 2.0	Display Port 1.2 / USB Type-C
640x480@60Hz
640x480@75Hz
720x480@60Hz
800x600@60Hz
800x600@75Hz
1024x768@60Hz
1024x768@75Hz
1280x720@60Hz
1280x720@120Hz
1920x1080@60Hz
1920x1080@120Hz
1920x1080@144Hz
2560x1440@60Hz
2560x1440@120Hz
2560x1440@144Hz
2560x1440@165Hz
2560x1440@170Hz

Troubleshooting

Note: If the problem persists, please contact our customer service for further assistance.

Basic Care

When the screen becomes dirty, do the following to clean the screen:

• Wipe the screen with your soft, lint-free cloth to remove any residual dust.
• Spray or apply the cleaning fluid onto a soft cloth. Then wipe the screen gently with the damp cloth.

Note:

• Make sure that the cloth is damp, but not wet.
• When wiping, avoid applying excessive pressure on the screen.
• Acidic or abrasive cleaners can damage the screen.

Notes on USB Charging

The following devices are not compatible with BC 1.2 of CDP mode. When the Hub is connected to a PC, these devices cannot be charged using the USB cable.

SAFETY INFORMATION

Safety Precautions
Read through the following Safety Precautions before using the monitor.

• Only use the accessories that are provided with the monitor or that which are recommended by the manufacturer.
• Keep the plastic packaging bag for the product in a place that cannot be reached by children.
• Before connecting the monitor to the power outlet, make sure that the voltage rating of the power cable is compatible with the power specification in the country where you are located.
• The power cord plug must be connected to a properly wired and grounded power outlet.
• Do not touch the plug with wet hands, otherwise easily cause electric shock.
• Place the monitor in a stable and well-ventilated place.
• Do not place the monitor near any heat sources such as electric radiators or direct sunlight.
• The holes or openings on the monitor are for ventilation. Do not cover or block the ventilation holes with any objects.
• Do not use the monitor near water, drinks, or all types of liquids. Failure to do so may result in electric shock or damage to the monitor.
• Make sure to unplug the monitor from the power outlet before cleaning.
• As the screen surface is easy to be scratched, avoid touching the surface with any hard or sharp object.
• Use a soft lint-free cloth instead of a tissue to wipe the screen. You may use a glass cleaner to clean the monitor if required. However, never spray the cleaner directly onto the screen.
• Disconnect the power cable if the monitor is not being used for a long period of time.
• Do not attempt to disassemble or repair the monitor yourself.

GIGABYTE Service Information
More service information, please visit GIGABYTE official website: https://www.gigabyte.com/

Copyright
© 2020 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.
The trademarks mentioned in this manual are legally registered to their respective owners.