biossun BIO230 NVS Installation Instructions Manual

Pergola

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

Installation instructions

Pergola BIO230 NVS

Table of Contents

Need help?

Do you have a question about the BIO230 NVS and is the answer not in the manual?

Questions and answers

Summary of Contents for biossun BIO230 NVS

Page 1 Installation instructions Pergola BIO230 NVS...
Page 2: Table Of Contents
Fit the cover of the opposite motor position rod ..................... 43 5.23. Set up the electronics in the technical post ...................... 44 5.24. Fit the posts cover ............................. 46 Troubleshooting ................................47 Technical data .................................. 48 Index ....................................49 Pergola BIO230 NVS...
Page 3: Directives
Address Biossun SAS 24 rue de la Sure 38360 Sassenage FRANCE Phone +33 (0)4.80.42.08.10 e-mail info@biossun.com Other applicable documents User manual for pergola § If included in scope of supply: Instruction manual for radio § remote control Pergola BIO230 NVS...
Page 4: Overview
2.1. 3D overview SLAT RIGHT LATERAL BEAM MOTION ROD MOTOR BEAM MOTOR OPPOSED BEAM LEFT LATERAL BEAM POST 2.2. Tools overview Sledgehammer Concrete drill Screwer extension Dynamometric wrench Open-end spanner Spirit level Drill Screwer Silicone Tape measure Pergola BIO230 NVS...
Page 5: Fixing Options
2.3. Fixing options: o Standard (directly to the ground) >105. 00 mm >105. 00 mm o Wide plate <105. 00 mm <105. 00 mm Pergola BIO230 NVS...
Page 6: Safety
The signal words described above are used. Example: Loosen the screw. CAUTION! Risk of pinching by cover! Close the cover carefully. Tighten the screw. Pergola BIO230 NVS...
Page 7 Work on the electrical components must be performed by qualified electricians only. The pergola may only be connected if the specifications on the type plate match the power supply voltage. Observe the enclosed motor operating manual. Pergola BIO230 NVS...
Page 8 Securely attach the ropes to the awning. Make sure that the pergola cannot slip free of the ropes. Keep the pergola horizontal when lifting it. Do not enter the danger zone beneath the load. Pergola BIO230 NVS...
Page 9 If necessary, use lifting gear. Secure components to prevent them from falling or toppling over. Consult Biossun SAS in any cases of doubt. Operating the slats NOTICE! Risk of property damage when extending the awning! When rotating the slats, there is a risk of damaging them if they collide with obstacles.
Page 10 Industrial helmets protect the head against falling objects, swinging loads and impacts with fixed objects. Safety goggles Safety goggles protect your eyes from flying parts and spraying liquids. Safety shoes Safety shoes protect the feet from crushing, from dropping parts, and from slipping on slippery floors. Pergola BIO230 NVS...
Page 11: Preparing Assembly
4. Preparing assembly 4.1. Checking the basic elements delivered Motor beam Motor opposed beam Position rod cover Pergola BIO230 NVS...
Page 12 Right lateral beam Left lateral beam Pergola BIO230 NVS...
Page 13 Motion rod Posts/Technical post Slats Pergola BIO230 NVS...
Page 14: Checking The Power Supply Characteristics
Checking the power supply characteristics Make sure your power supply has the following characteristics: Voltage: 230 V, Frequency: 50 Hz, Electric protection: 10 A protection with a 30mA differential, Power cable: Three-wires cable with grounding (min. Ø1.5 mm2) Pergola BIO230 NVS...
Page 15: Checking The Fixing Supports (Walls And Floor)
140, 00 mm In case of wall mounting you may face two situations: 90,00 mm 70,00 mm Installation against a concrete wall Concrete anchor specification Type M12 x 120 Shear strength 17 kN Tensile strength 9 kN Pergola BIO230 NVS...
Page 16: Choice Of Fixing Materials
Before you start installing our product, make sure you have a clearance of at least 100mm above the top of the pergola: cle aran ce > 10 0 mm 4.4. Choice of fixing materials Whether you install the pergola on the ground or against a wall, always use stainless steel screws. Pergola BIO230 NVS...
Page 17: Mounting The Pergola
5. Mounting the pergola 5.1. Place the beams on trestles 5.2. Connect the various cables and extensions Connect matching colors While doing this step, keep in mind that the various cables must end up in the technical post. Pergola BIO230 NVS...
Page 18: Assemble The Corners And Seal Them
The number of cables and m ac hinings depend on your c onf iguration The rain and wind sensors cables layout must be addressed at this step, before assembling the corners. 5.3. Assemble the corners and seal them Pergola BIO230 NVS...
Page 19 TAPTITE II M6x1 6 TTPT screw s Pergola BIO230 NVS...
Page 20: Mount The Top Pdls
TAPTITE II M6x1 6 TTBT screw s 5.4. Mount the top PDLs WARNING The way y ou angle t he PDL impac t the way the post is angled Pergola BIO230 NVS...
Page 21: In Case Of Wall Mounting, Drill Holes In The Frame(S) Intended To Be Set Against The Wall(S)
M10 x40 CH C screws Tightening torque : 33 N.m 5.5. In case of wall mounting, drill holes in the frame(s) intended to be set against the wall(s) 80 0,00 mm 80 0,00 mm 50 0,00 mm 105, 00 mm Pergola BIO230 NVS...
Page 22 50 0,00 mm 105, 00 mm 125, 00 mm 105, 00 mm Pergola BIO230 NVS...
Page 23: Set In Place The Ep With A Layer Of Sealing
5.6. Set in place the EP with a layer of sealing Tap pin g screws Ø4.2x16 TOR X Pergola BIO230 NVS...
Page 24: Seal Every Junction
5.7. Seal every junction Pergola BIO230 NVS...
Page 25: Reassemble The Wheel Of The Motor(S) And Install The Motor Cover
5.8. Reassemble the wheel of the motor(s) and install the motor cover Pergola BIO230 NVS...
Page 26 "Cli ck " "Cli ck" Pergola BIO230 NVS...
Page 27: Install The Motion Rod And Link It With The Motor(S)
View from inside/through the motor beam 5.9. Install the motion rod and link it with the motor(s) Pergola BIO230 NVS...
Page 28 Tightening torque : 7 N.m Sel f-l ockin g nut M6 He x so cket b utto n hea d cap screw w ith coll ar M6x40 Pergola BIO230 NVS...
Page 29: Install A Slat At Each End And Next To Each Motor
5.10. Install a slat at each end and next to each motor Stand ard sla ts Motor sla t(s) MOTOR SLAT Pergola BIO230 NVS...
Page 30 Pergola BIO230 NVS...
Page 31: Cut The Posts To Size (If Necessary, And Move The Bottom Pdls Inside The Posts)
5.11. Cut the posts to size (if necessary, and move the bottom PDLs inside the posts) Pergola BIO230 NVS...
Page 32: Raise The Pergola Above Its Installation Height
> 10 0 mm 5.12. Raise the pergola above its installation height Use 2 to 4 pergola-lifters for this manoeuvre Pergola BIO230 NVS...
Page 33: Set The Posts In Place On The Ground
5.13. Set the posts in place on the ground Standard mounting Tightening torque : 57 N.m OPTIONAL Wide plate mounting He x h ead scre ws M12x2 0 (no t pro vide d) Pergola BIO230 NVS...
Page 34: Lower The Pergola On Its Posts
OPTIONAL Wide plate mounting 5.14. Lower the pergola on its posts Pergola BIO230 NVS...
Page 35: In Case Of Wall Mounting, Set The Pergola Next To The Intended Wall, Drill The Wall And Tighten The Fixation
5.15. In case of wall mounting, set the pergola next to the intended wall, drill the wall and tighten the fixation Pergola BIO230 NVS...
Page 36 (Anchor bol ts not prov ided) Tightening torque : 50 N.m (Nu ts no t pro vide d) Pergola BIO230 NVS...
Page 37: Check That The Posts Are Vertical And That The Diagonals Are Equal
5.16. Check that the posts are vertical and that the diagonals are equal 5.17. Lock upper PDLs in place Tightening torque : 17 N.m Pergola BIO230 NVS...
Page 38: Fix The Posts To The Ground
5.18. Fix the posts to the ground Standard mounting (Anch or bol ts no t pro vide d) Standard mounting Pergola BIO230 NVS...
Page 39 Tightening torque : 50 N.m (Nu ts no t pro vide d) Standard mounting OPTIONAL Wide plate mounting Pergola BIO230 NVS...
Page 40 (Anch or bol ts no t pro vide d) OPTIONAL Wide plate mounting Tightening torque : 50 N.m (Nu ts no t pro vide d) OPTIONAL Wide plate mounting Pergola BIO230 NVS...
Page 41: Lock Bottom Pdls In Place
5.19. Lock bottom PDLs in place Tightening torque : 17 N.m 5.20. Pipe the EP post (if necessary) Pergola BIO230 NVS...
Page 42: Put The Slats In Place
81 ,0 0 mm mini 7 5,00 mm 5.21. Put the slats in place For information on how to install the slats, refer to 5.10 Pergola BIO230 NVS...
Page 43: Fit The Cover Of The Opposite Motor Position Rod
5.22. Fit the cover of the opposite motor position rod Pergola BIO230 NVS...
Page 44: Set Up The Electronics In The Technical Post
He xalo bul ar socket pan h ead tap pin g screw ST4.2x45 5.23. Set up the electronics in the technical post Connect the unplugged connectors to their counterparts (matching colors) coming through the top PDL. Once there is no free connectors left, connect the 230 V. Pergola BIO230 NVS...
Page 45 LIGHT (S) BOX MOT ORBO X TRANSFORMER TRANSFORMER "Y" POWER CONNECT OR CONNECT THE VA RI OUS CA BLES 230V NOTA THE NUMBER OF CABL ES AN D BOXES DEPENDS ON YOUR C O N F IGURAT ION Pergola BIO230 NVS...
Page 46: Fit The Posts Cover
5.24. Fit the posts cover Pergola BIO230 NVS...
Page 47: Troubleshooting
6. Troubleshooting Pergola BIO230 NVS...
Page 48: Technical Data
VOLTAGE SUPPLY POWER MOTOR DATA VALUE UNIT VOLTAGE SUPPLY POWER SPOT DATA VALUE UNIT VOLTAGE SUPPLY POWER PER SPOT 3 / 5 LED WHITE DATA VALUE UNIT VOLTAGE SUPPLY POWER LED RGB DATA VALUE UNIT VOLTAGE SUPPLY POWER Pergola BIO230 NVS...
Page 49: Index
.............. 10 Safety ..............6 Commisionning ............ 39 corners ..............12 Technical data ............41 technical post ............37 Dimensions ............41 Tools ............... 4 Troubleshooting ........... 40 Electrical power supply ........41 wall mounting ............15 Pergola BIO230 NVS...