Advertisement
Quick Links
PARTS EXPLOSION
Parts List
Ref
Part
Item
No.
No.
Description
—
555812
Mark V Chisel Sharpener
1
120392
. Flat Washer .................................. 2
2
126315
. Carriage Bolt, 1/4-20x1 ............. 1
3
274737
. Nut, 10-24 .................................... 4
4
436691
. Pan Head Machine Screw ......... 2
5
436732
. Philips Screw, 10-24x1/2 ........... 4
6
502973
. Split Washer ................................ 4
7
513216
. Wing Nut ..................................... 1
8
513739
. Flat Washer .................................. 1
9
514491
. T-Nut ............................................ 1
10
515318
. Eye Shield .................................... 1
11
521662
. Knob ............................................. 1
12
521768
. Knob ............................................. 1
Qty
9
21
16
1
7
15
11
8
18
CHISEL SHARPENER
Ref
Part
Item
No.
No.
Description
13
521846
. Chisel Bracket ............................. 1
14
521847
. Chisel Protractor ......................... 1
15
521849
. Support Angle ............................. 1
16
521853
. Set Screw ...................................... 1
17
521854
. Chisel Stud .................................. 1
18
521855
. T-Nut Assembly ......................... 1
—
521903
. Arm & Label Assembly ............. 1
19
521856*
. . Arm ............................................. 1
20
521899
. . Warning Label, Rotation ......... 1
21
521859
. Cup Assembly ............................. 1
22
521879
. Bracket, Eye Shield ...................... 1
23
521881
. Sharpening Plate (not shown) ... 1
24
521898
. Warning Label, Dust Collection 1
* Not available as a service part.
3
22 6
5
10
5
3
6
17
4
14
13
2
20
12
19
555812
1
Qty
Advertisement
Related Manuals for Shopsmith 555812
Summary of Contents for Shopsmith 555812
- Page 1 CHISEL SHARPENER 555812 PARTS EXPLOSION Parts List Part Item Part Item Description Description — 555812 Mark V Chisel Sharpener 521846 . Chisel Bracket ......1 120392 . Flat Washer ........2 521847 . Chisel Protractor ......1 126315 . Carriage Bolt, 1/4-20x1 ..... 1 521849 .
-
Page 2: General Safety
CHISEL SHARPENER 555812 INTRODUCTION WARNING General Safety The Chisel Sharpening Attachment allows you to sharpen various sizes and shapes of • Wear proper eye and ear protection. chisels. Straight -edged chisels, curved edge Also, wear a dust mask. chisels, steep-angle lathe scraping tools, and low angle carving chisels can all be sharpened •... -
Page 3: Tools Required
555812 CHISEL SHARPENER operate a power tool that is not function- ing properly. tion manuals, which came with your MARK V and Strip Sander. • Do not overreach. Keep proper footing and balance at all times. • Read the Safety section and complete the Assembly and Setup procedures •... - Page 4 CHISEL SHARPENER 555812 Figure 1 Figure 4 Pick up bracket (15), with bent tab down (5), as shown in Figure 4. slide stud of t-nut asm. (18) up through the round hole. With t-nut asm. parallel, NOTE add washer (8) and knob (11), as shown in Figure 1.
- Page 5 555812 CHISEL SHARPENER Open the Strip Sander cover, hold bracket and guard assembly against the top of the frame. Slip screw through the hole in the bracket and through the casting. See Fig- ure 5. Add lock washer and nut to screw and tighten with Phillips screwdriver and 3/8”...
-
Page 6: Basic Operations
CHISEL SHARPENER 555812 WARNING too much pressure or the belt has become dull and needs replaced. Finer belts will wear quickest and will need to be replaced Failure to mount Strip Sander (as described most often. in Step 1) will cause the abrasive belt to run in the wrong direction, and will cause the Grinding, Sharpening &... - Page 7 555812 CHISEL SHARPENER To Copy the Tool’s Bevel If the scratches are only at the tool’s tip, then turn speed on speed dial to “slow” and turn off the headstock. Loosen the Place a 100, 150, or 220 grit abrasive belt trunnion lock knob, lower the arm on the Strip Sander.
- Page 8 CHISEL SHARPENER 555812 Place the tool handle in the cup and grind the new bevel against the moving belt. After the initial bevel grind is completed, turn down and turn off the Mark V. Open the Strip Sander, remove the belt and install the next finer grit.
- Page 9 555812 CHISEL SHARPENER Check your progress often and check chisel temperature. Cool in water as needed. Turn the skew chisel over and grind the opposite side, checking that the bevel is a constant width on both sides. If it is not...
- Page 10 CHISEL SHARPENER 555812 Check your progress often to check chisel temperature. Cool in water as needed. To grind a pointed gouge for spindle turning, more grinding is done on either side, see Figure 15. Front Figure 17 Back NOTE Figure 15...
- Page 11 555812 CHISEL SHARPENER Slide the support bracket up the arm until cutting edge against the bent without its edge is even with the top end of the rotating the chisel. arm and tighten the support bracket knob. Check your progress often to check chisel Loosen the trunnion lock knob and rotate temperature.
- Page 12 CHISEL SHARPENER 555812 NOTES 845515 Rev. B 01-10 RLFSHOP, LLC. www.shopsmith.com 6530 Poe Avenue All Rights Reserved Dayton, Ohio 45414 Printed In U.S.A.
- Page 13 555812 CHISEL SHARPENER TEMPLATE LINE “A” 845518 Rev. 12/00 All Rights Reserved www.shopsmith.com Printed In U.S.A. 6530 Poe Avenue Dayton, Ohio 45414...
Need help?
Do you have a question about the 555812 and is the answer not in the manual?
Questions and answers