Table of Contents
Advertisement
Quick Links
11/25/2019
Cisco Aironet Power Injector (AIR-PWRINJ5) Installation Guide
Updated: June 24, 2017
Table of Contents
Cisco Aironet Power Injector (AIR-PWRINJ5) Installation Guide
Preface
Cisco Aironet Power Injector
Unpacking the Power Injector
Additional Requirements
Installing the Power Injector
Mounting Instructions
Using the Mounting Tabs
Speci cations
Mechanicals
Regulatory Information
Applicable Standards
Cisco Aironet Power Injector (AIR-PWRINJ5) Installation Guide
Preface
The Cisco Aironet Power Injector (AIR-PWRINJ5) increases wireless LAN deployment exibility of Cisco
Aironet Access Points by providing an alternative powering option to local power, inline power-capable
multiport switches, and multiport power patch panels.
The single-port Cisco Aironet Power Injector provides 802.3af power and data signal, sending both to the
Cisco Aironet Access Point.
The power injectors provide up to 15.4 W over the unused wire pairs of a Category 5 or better Ethernet
cable, supplying enough power for a distance of 328 ft. (100 m) on the Cisco Aironet 1040, 1140, 1260,
2600, and 3500 Series Access Points. While it can also support the Cisco Aironet Series 3600 Access Points
when modules are not being used, it is recommended to use the AIR-PWRINJ4= power injector instead for
the 3600 series, as it has su cient power to supply to the AP and any installed modules.
This guide covers the following Cisco Aironet Power Injector:
Cisco Aironet Power Injector (AIR-PWRINJ5)
Cisco Aironet Power Injector
The Cisco Aironet Power Injector provides both power and data to a connected Cisco Aironet Access Point.
The device serves the following functions:
It provides Category 5 or better Ethernet media to the access point.
https://www.cisco.com/c/en/us/td/docs/wireless/power/quick/guide/pwrinj5.html
Cisco Aironet Power Injector (AIR-PWRINJ5) Installation Guide - Cisco
1/6
Advertisement
Table of Contents
Related Manuals for Cisco Aironet AIR-PWRINJ5
Summary of Contents for Cisco Aironet AIR-PWRINJ5
- Page 1 The power injectors provide up to 15.4 W over the unused wire pairs of a Category 5 or better Ethernet cable, supplying enough power for a distance of 328 ft. (100 m) on the Cisco Aironet 1040, 1140, 1260, 2600, and 3500 Series Access Points. While it can also support the Cisco Aironet Series 3600 Access Points when modules are not being used, it is recommended to use the AIR-PWRINJ4= power injector instead for the 3600 series, as it has su cient power to supply to the AP and any installed modules.
- Page 2 The power injector is used with the following Cisco Aironet Series Access Points: 1040 series access points...
- Page 3 Power cord URL Pointer Card and China RoHS Statement If any item is missing or damaged, contact your Cisco representative or reseller. Additional Requirements Use the power cord that shipped with your power injector to supply power for the injector. If you install the access point in an environmental air space such as above a suspended ceiling, check national and local safety codes to make sure that the Ethernet cable you connect to the unit meets applicable standards.
- Page 4 11/25/2019 Cisco Aironet Power Injector (AIR-PWRINJ5) Installation Guide - Cisco Note The maximum distance that is supported for in-line power is 328 ft. (100 m), including the length of the 6.5-ft. (2-m) Ethernet cable provided with the power injector. Installing the Power Injector Follow these steps to install the power injector: 1.
- Page 5 You can determine whether your equipment is causing interference by turning it o . If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes https://www.cisco.com/c/en/us/td/docs/wireless/power/quick/guide/pwrinj5.html...
- Page 6 Modi cations to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product.
Need help?
Do you have a question about the Aironet AIR-PWRINJ5 and is the answer not in the manual?
Questions and answers