Do you have a question about the VX100 and is the answer not in the manual?
Questions and answers
Ian Girot
April 6, 2025
Can’t get cover off.can you help,picture attached
1 comments:
Mr. Anderson
April 6, 2025
To remove the cover from the Xpelair VX100, first unplug the unit from the power supply. Then, remove the plastic fan blade on one side. On the other side, there are two screws—approximately one inch long—that need to be removed. Once these screws are out, the cover should lift out toward you. If it's stuck, gently bend or adjust the plastic, possibly using pliers, to release it.
The appliance is double insulated and does not require an earth connection. This appliance is intended for connection to fixed wiring. General information Included in the box: VX100/120/150 VX100T/120T/150T* Tools for installation:...
What you will need Australia Only Always check the appropriate size of space before installing the fan. VX100 / VX120 / VX150 Wall Mounting clearance between contacts. Ceiling Mounting Australia Only VX100T / VX120T / VX150T clearance between contacts.
J. For location of see K. Step 5 Step 6 VX100 / VX120 / VX150 switch to the point of connection to Finally refit the electrical cover ‘O’ ring seals Warning: Do not make any connections (where applicable) and screw in place.
Controleer of de netspanning is uitgeschakeld, voordat u elektrische aansluitingen maakt of onderhouds- of schoonmaakwerkzaamheden uitvoert. Het apparaat is dubbel geïsoleerd en heeft geen aarding nodig. Dit apparaat is bedoeld voor aansluiting op vaste bedrading. Algemene informatie De doos heeft de volgende inhoud: VX100/120/150 Installatiegereedschap: VX100T/120T/150T*...
Wat u nodig heeft Alleen voor Australië VX100 / VX120 / VX150 installeert. Wandmontage Plafondmontage Alleen voor Australië VX100T / VX120T / VX150T...
Page 12
VX100T / VX120T / VX150T zie J. Stap 5 zie K. Stap 6 VX100 / VX120 / VX150 Waarschuwing: Maak in dit stadium nog geen verbindingen met de netvoeding. Plaats tot slot de ‘O’-ringen van de sto ap Stap 7...
électrique ou d’e ectuer toute opération d’entretien ou de nettoyage. L’appareil étant à double isolation, il ne nécessite aucune prise de terre. Cet appareil est destiné à être raccordé à des câblages fixes. Généralités Inclus dans la boîte : VX100/120/150 Outils nécessaires à l’installation : VX100T/120T/150T*...
Page 15
à hauteur des yeux. En cas d’installation atmosphères potentiellement corrosives et dans une pièce équipée d’un dispositif de chimiques. Ressources nécessaires Australie uniquement VX100 / VX120 / VX150 Montage mural Montage au plafond Australie uniquement VX100T / VX120T / VX150T contacts.
VX100T / VX120T / VX150T voir point J. Étape 5 voir point K. Étape 6 VX100 / VX120 / VX150 Avertissement : N’e ectuer aucun raccordement à l’alimentation électrique à ce stade. Étape 7 Enfin, remonter les joints toriques du couvercle électrique (le cas échéant), puis les visser en...
Es muss sichergestellt werden, dass die Netzversorgung unterbrochen ist, bevor elektrische Verbindungen hergestellt oder Wartungs- oder Reinigungsarbeiten durchgeführt werden. Das Gerät ist doppelt isoliert und erfordert keinen Erdanschluss. Dieses Gerät ist für den Anschluss an eine feste Verkabelung bestimmt. Allgemeine Informationen Im Karton enthalten: VX100/120/150 Werkzeuge für die Montage: VX100T/120T/150T*...
Raum mit einer raumluftabhängigen in möglicherweise chemisch korrosiver Brennsto verbrennungsvorrichtung liegt Atmosphäre. Was Sie benötigen Nur für Australien VX100 / VX120 / VX150 Wandmontage Deckenmontage Nur für Australien VX100T / VX120T / VX150T Nur für das Vereinigte Königreich (alle Typen)
Page 20
Installation von Schaltern und Kabeln Lüfterinstallation Schritt 1 – Lüfter für Installation Nasszellen: Ein-/Ausschalter muss so platziert sein, dass er nicht von Personen, die das Bad vorbereiten oder die Dusche nutzen, berührt werden kann. Eine Möglichkeit zur Abschaltung in allen Polen muss gemäß...
Need help?
Do you have a question about the VX100 and is the answer not in the manual?
Questions and answers
Can’t get cover off.can you help,picture attached
To remove the cover from the Xpelair VX100, first unplug the unit from the power supply. Then, remove the plastic fan blade on one side. On the other side, there are two screws—approximately one inch long—that need to be removed. Once these screws are out, the cover should lift out toward you. If it's stuck, gently bend or adjust the plastic, possibly using pliers, to release it.
This answer is automatically generated