Download Print this page
Sealey 1020LE.V3 Series Instructions
Sealey 1020LE.V3 Series Instructions

Sealey 1020LE.V3 Series Instructions

Low entry short chassis trolley jack

Advertisement

Quick Links

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear safety
instructions
footwear
1. SAFETY
IMPORTANT SAFETY WARNING: ALWAYS USE AXLE STANDS
Please remember a trolley jack is a lifting device and is not designed to support a load. Never get
underneath a vehicle supported only by a jack - your life is at risk. We stock a comprehensive
range of axle stands.
Please see relative section of catalogue or website for full details.
Ensure the jack is in sound condition and good working order. Take action for immediate repair
9
or replacement of damaged parts. Use genuine parts only. The use of unapproved parts may be
dangerous and will invalidate the warranty.
Locate the jack in a suitable, well lit working area.
9
Keep working area clean and tidy and free from unrelated materials.
9
Use jack on level and solid ground, preferably concrete. Avoid tarmacadam as jack may sink in.
9
Place wedges under wheels of vehicle.
9
Ensure the vehicle handbrake is engaged, engine is switched off and transmission is in gear
9
(or "PARK" if automatic).
Ensure minimum distance of 0.5m between vehicle and static objects such as doors, walls, etc.,
9
to allow for vehicle tilting.
Ensure there are no passengers in the vehicle.
9
Ensure all non-essential persons keep a safe distance whilst the jack is in use.
9
Only place jack under those lifting points recommended by vehicle manufacturer
9
(see vehicle hand book).
Check the lifting point is stable and centred on the jack saddle.
9
Ensure the jack wheels are free to move and that there are no obstructions.
9
When lifting a load at the jack's maximum rating (2tonne) or close to it, it is recommended that
9
the effort of raising the load be reduced by the assistance of a second person during this operation.
DANGER: Use the jack for lifting only, NOT for supporting the lifted load.
Use suitable capacity axle stands under the vehicle before proceeding with any task.
9
Ensure there are no persons or obstructions beneath the vehicle before lowering.
9
Use a qualified person to maintain or repair the jack hydraulic system.
9
DO NOT operate the jack if damaged.
8
DO NOT allow untrained persons to operate the jack.
8
DO NOT exceed the rated capacity of the jack.
8
DO NOT allow the vehicle to move while supported by the jack, or use the jack to move the vehicle.
8
DO NOT jack vehicle if there is a risk of spillage of fuel, battery acid, or other dangerous substances.
8
DO NOT work under the vehicle until axle stands have been correctly positioned.
8
DO NOT use the jack for purposes other than those for which it is intended.
8
DO NOT top up hydraulic system with brake fluid. Use hydraulic jack oil only. (Sealey Part No:
8
HJO500MLS or HJO5LS)
8
DO NOT adjust the safety overload valve.
8
When not in use store jack, fully lowered, in a safe, dry, childproof area.
9
2. INTRODUCTION
Heavy-duty chassis with strengthening flanges along the top edge for extra torsional rigidity under
load. Profiled lifting arm allows low clearance height of just 85mm making this unit suitable for
sports and custom cars. Fitted with heavy-duty one-piece hydraulic unit with pump-through action
preventing handle locking at maximum ram extension. White saddle aids positioning under vehicle
and safety valve prevents overloading.
© Jack Sealey Limited
2TONNE LOW ENTRY SHORT CHASSIS
TROLLEY JACK
1020LE.V3 SERIES
MODEL NO:
Original Language Version
TJL3
1 3 5
2 4 R
Use on
Chock
wheels
Close
Lower
Lift & twist
to lower
Use suit ble xle st nds
X2
w w w . s e
1020LE.V3 SERIES Issue 2 (2,3) 30/04/21
Apply
h ndbr ke
h rd level floor
Never
exceed
j ck c p city
R ise
OR
R ise
l e y . c o . u k

Advertisement

loading

Summary of Contents for Sealey 1020LE.V3 Series

  • Page 1 1020LE.V3 SERIES MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
  • Page 2 Remove oil filler plug (fig.3). The correct level is just below the bottom of the plug. If oil level is low, fill as required. Replace cover. NOTE: Use a good quality jack oil, such as SEALEY HYDRAULIC JACK OIL.
  • Page 3 Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 sales@sealey.co.uk...