ClearWater STELLA, ST2 - Mono Kitchen Mixer Fitting And Parts List Manual

PARTS LIST

In the unlikely event you find a part missing please contact our Customer Service Helpline on 01684 299555 for immediate despatch of part.

MAINTENANCE

IF THE FITTING BEGINS TO DRIP

1. Turn off the water supply
2. Loosen grub screw under handle lever, remove handle and valve
3. Carefully clean seating, rubber washer and ceramic disc
4. Replace valve and handle, then turn on the water supply
5. If problem persists contact our helpline quoting the product code

Where an aerator is fitted to the outlet of the spout, it will need occasional cleaning.
This will be evident when the water flow slows down to an unacceptable level. To accomplish this unscrew the outlet in an anti-clockwise direction and remove the mesh. Immerse the mesh in a suitable descaling fluid overnight, rinse throughly in clean water and re-install.

REMEMBER

Maximum water supply pressure 5 bar (75PSI) Minimum water supply pressure 0.5 bar
Maximum hot water supply temperature 70˚C
Recommended hot water supply temperature 65˚C
If these temperatures or water pressure are exceeded, damage to the tap can result. A pressure reducing valve may be required to be fitted in high water pressure situations.

PREPARATION

We strongly recommend installing particle filters and isolation valves to both hot and cold feeds. This will help to prevent premature failure of valves and make any future maintenence easier.
Flush the plumbing system before installing the mixer tap. This is to void plumbing residues clogging the mesh of the aerated outlet, or possibly damaging the valve's washers. This is especially important where extensive plumbing work has been carried out.
First shut off your water heating system then, with your mains stop cock closed, open the lowest hot and cold taps in the house and allow to run until the cold storage tank and pipes are empty. (The hot water storage cylinder always remains full).

INSTALLATION

• Screw the flexi-tails into the mixer body, and fully hand tighten. Do not attach the filter tail in till the tap has been passed through the tap hole, as it will be tight getting the tails through the tap hole.
• Pass the rubber washer over the flexi-tails and threaded stud to form a seal on sink top with the tap plinth.
• Pass the flexi-tails and fixing stud through the sink top from above and place the mixer in position on the sink.
• Slide the flat washer and fixing nut up the flexi tails, and then screw the nut all the way up making sure the tap is in the correct position.
• It is recommended that 15mm x 15mm compression fitting be used to connect mixer to supply pipes.
• Install the twist lock head to the cupboard carcass leaving adequate room to remove the filter.
• Screw in the push fit connectors, part (L9S025N) making sure the rubber gasket is used; into the in and outlet lines as labelled.
• Cut ¼'' tube into two pieces, adequate so that it reaches your filter head. Simply push the tubes into the filter head holding the little tab back. Do the same into the push fit connectors part (L9S025N).
• Install the twist lock cartridge.
• Having first checked all the new connections, turn on the mains stop cock, close all taps except the new mixer and as the system starts to refill check for leaks.
• FOR BEST RESULTS
  Run off around 5 litres of water from the filter line prior to drinking.
  Reduce the cold water flow so that the filter line works at around 2 litres per minute. This will maximise the filter contact time in the filter.
  The filter must be changed at least every 12 months. We suggest changing the cartridge every 6 months in normal household usage (filter life 4000 litres usage).
• USING OTHER FILTERS/WATER SOFTENING SYSTEMS
  This tap uses a recirculation method, so softened water systems cannot be installed in conjunction as it will contaminate the filter water. Other filter systems can be used but you will have to follow the same connection method as shown in the diagram.
• OTHER
  Remember to fill in and send off your free post warranty form.

AFTER CARE

To maintain the appearance of this tap, ensure that it is regularly cleaned only using a clean, soft damp cloth. A solution of warm water and a mild liquid detergent may be used where necessary, and then the fitting rinsed thoroughly and wiped dry. Abrasive cleaners, scouring cleaners and acid cleaners must not be used under any circumstances. All bath cleaning powders and liquids will damage the surface of your fitting even the non-scratch cleaners.
Avoid contact with all solvents and any harsh household chemicals. You will damage the plated finish and void your guarantee.

GUARANTEE AND LIABILITY

In the unlikely event that you should experience any defect in the material or workmanship of your mixer tap within 5 years of purchase, we will replace the faulty part free of charge.
Decorative surface finishes are guaranteed for one year from the date of purchase provided that our advise concerning care has been observed and no scouring agents have been used. This is provided that the mixer or tap has been used for normal domestic purposes in the UK and that the care, installation and maintenance instructions have been observed.
Scuff and scratches caused by normal wear and tear, improper installation or accidental damage are excluded from this guarantee.
You should retain a copy of your dated invoice as proof of purchase to validate any claims under this guarantee.
No other warranties, express or implied, are made, including merchantability or fitness for a particular purpose.

Spare Parts and Service

Contact: Sterling
Phone: 01684 299555
Fax: 01684 290958
Email: sales@sterling.eu.com
Website: www.sterling.eu.com