Sealey VS0204UA Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instructions protection
1. SAFETY
IMPORTANT! These instructions are provided as a guide only. Always refer to the vehicle manufacturer's service instructions.
It is recommended to perform a leak test to ensure if the adaptor is tightly and securely connected on the reservoir.
9
Keep this product in good working order and condition, take immediate action to repair or replace damaged parts.
9
Use approved parts only. Unapproved parts may be dangerous and will invalidate the warranty.
9
Keep children and unauthorised persons away from the work area.
9
Keep work area clean and tidy and free from unrelated materials.
9
Ensure the work area has adequate lighting.
9
DO NOT use the kit to perform a task for which it is not designed.
8
DO NOT allow untrained persons to use the kit.
8
DO NOT use when tired or under the influence of drugs, alcohol or intoxicating medication.
8
After use, clean equipment and store in a cool, dry, childproof area.
9
Dispose of waste liquids in accordance with local authority regulations.
9
Always read and comply with the warnings on the brake fluid container.
9
Wear eye protection and keep skin contact to a minimum. If brake fluid enters eyes rinse with plenty of water and seek medical
9
advice. If swallowed seek medical advice immediately.
WARNING! Only use new Brake Fluid, used Brake Fluid or other fluids will contaminate the system and possible brake system
‰
failure may result.
WARNING! DO NOT pollute the environment by allowing uncontrolled discharge of fluids.
‰
WARNING! Brake fluid is flammable - keep away from sources of ignition, including hot surfaces e.g. exhaust manifold.
‰
WARNING! Brake fluid will damage paintwork. Any spillage should be flushed with water immediately.
‰
2. INTRODUCTION
Universal brake and clutch bleeder adaptor cap fits most vehicles. 90° Rotating coupling with height adjustment for use where space is limited.
Adjustable securing wings connect to the master cylinder filling neck 114mm – 180mm. Brake fluid resistant EPDM rubber. Cap size Ø26 – Ø79mm.
Heavy-duty chrome steel construction.
3. OPERATION
REFER TO FIG1.
3.1. Remove the master cylinder reservoir cap and withdraw as much old
brake fluid as possible.
3.2. Unscrew the neck width adjusting nut and locate adjustable clamps on
neck of fluid container. Loosely tighten adjusting nut to hold the adaptor
in place.
3.3. Operate the height adjusting screw in order that the rubber sealing block
fits tightly onto the cylinder neck.
3.4. Connect the pressure bleeding tool or machine to the adaptor.
3.5.
Follow the instructions as specified by the pressure bleeding tool
or machine manufacturer.
3.6. It is recommended to perform a leak test to ensure if the adaptor is
tightly and securely connected on the reservoir.
4. MAINTENANCE
4.1. Ensure that the unit is de-pressurized before carrying out any maintenance
and drain all fluids from the fluid supply tube.
4.2.
Clean up any spilled brake fluid and wipe down with a clean cloth.
4.3. Store in a clean, dry and childproof location.
© Jack Sealey Limited
SEALEY BRAKE & CLUTCH BLEEDER CAP
UNIVERSAL ADAPTOR
MODEL NO:
Wear
protective
gloves
Original Language Version
VS0204UA
Rubber sealing block
Height adjusting screw
Neck width
Adjusting nut
fig.1
VS0204UA Issue 1 10/05/23