TP-Link TL-SF1005D User Manual
10/100mbps desktop switch
Hide thumbs
Also See for TL-SF1005D:
- Mounting manual (2 pages) ,
- User manual (4 pages) ,
- Installation manual (3 pages)
Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for TP-Link TL-SF1005D
Summary of Contents for TP-Link TL-SF1005D
- Page 1 TL-SF1005D TL-SF1008D TL-SF1016D 10/100Mbps Desktop Switch REV: 1.0.0 1910010004...
-
Page 2: Fcc Statement
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP- LINK TECHNOLOGIES CO., LTD. -
Page 3: Ce Mark Warning
CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. SAFETY NOTICES Cautions Do not use this product near water, for example, in a wet basement or near a swimming pool. Avoid using this product during an electrical storm. -
Page 4: Package Contents
Package Contents The following items should be found in your box: One TL-SF1005D/TL-SF1008D/TL-SF1016D Switch One Power Adapter This User Guide Note: Make sure that the box contains the above items. If any of the listed items are damaged or missing, please contact with your distributor. -
Page 5: Table Of Contents
1.1 Overview of the Product... 1 1.2 Convention... 1 1.3 Features... 1 Chapter 2. Installation... 2 2.1 Mounting the Switch on a Desk... 2 2.2 Power On ... 2 Chapter 3. Identifying External Components... 3 3.1 Front Panel ... 3 3.2 Rear Panel ... -
Page 6: Chapter 1. Introduction Of The Product
Uplink ports. The Switch is Plug-and-Play and each port can be used as general ports or Uplink ports and can be simply plugged into a server, a hub, a switch or a router and so on, using straight cable or crossover cable. -
Page 7: Chapter 2. Installation
Please avoid any heavy thing placed on the switch. 2.2 Power On Powering on the Switch, it will automatically initialize and its LED indicators will respond as follows: All of the Link/Act LED indicators will flash momentarily, which represents a resetting of the system. -
Page 8: Chapter 3. Identifying External Components
Chapter 3. Identifying External Components This Chapter describes the front panel, rear panel and LED indicators of the Switch. 3.1 Front Panel Figure 3-1 TL-SF1016D Switch Front Panel The Switch’s LEDs are located on the front panel. Power LED: This indicator will light up when the Switch powers on. -
Page 9: Appendix A: Specifications
Appendix A: Specifications General Standards Topology Protocol Data Transfer Rate Network Media(Cable) Number of Ports LED indicators Transfer Method MAC Address Learning Frame Filter Rate Frame Forward Rate Environmental and Physical Operating Temperature Storage Temperature Operating Humidity Storage Humidity IEEE802.3 10Base-T, IEEE802.3u 100Base-TX Star CSMA/CD Ethernet: 10Mbps (Half Duplex), 20Mbps (Full Duplex) -
Page 10: Appendix B: Troubleshooting
Appendix B: Troubleshooting The Power LED is not lit Check to see if the power cord is connected to the Switch properly, and make sure the power source is ON. The Link/Act LED is not lit when a device is connected to the corresponding port Check to see if the cable connectors are firmly plugged into the Switch and the device, and verify the connected device is turned on and working well.
Need help?
Do you have a question about the TL-SF1005D and is the answer not in the manual?
Questions and answers