Page 2
IMPORTANT SERVICE GUIDE ♦ MODE SWITCH (PROGRAM SWITCH) ASSEMBLY POINT 1) When installing the ass’y deck on the Main PCB, be sure to align the assembly point of mode switch. ASSEMBLY POINT (ALIGN TWO ARROWS) Fig. 1 ♦ HOW TO EJECT THE CASSETTE TAPE (If the unit does not operate on condition that tape is inserted into housing ass’y) 1) Turn the Gear Worm Œ...
Page 3
Alternatively, wear a discharging Wrist-strap device. (Be sure to remove it prior to applying power--this is an electric shock precaution.) Samsung Electronics...
Page 4
Always inspect for pinched, out- of-place, or frayed wiring. Do not change the spacing between components and the printed circuit board. Check the AC power cord for damage. Make sure that leads and components do not touch thermally hot parts. Samsung Electronics...
Page 5
3) When replacing the cylinder ass’y, be sure to adjust the “X-Point” and “Head switching adjustment”. 4) Among Samsung VCR remote control used for adjustment as a accessory, only the remote control that has figures buttons (0 ~ 9) is available for all adjustment regardless of chassis.
Page 6
Alignment and Adjustment 2-1-2 Test point location for adjustment mode setting Application Models ; SV-G180UM/G175UM/G170UM/G75UM/G70UM/G100UP/G70P/G50UP/G180P/G175P/G171P/G75P/G71P Short-Circuit for a second and release. Fig. 2-2 Main PCB (Top View) Samsung Electronics...
Page 7
Alignment and Adjustment Application Models ; SV-G95UMA/G45UMA/G55UP/G45UPA/G45UPV/G45PA/G45PV Short-Circuit for a second and release. Fig. 2-3 Main PCB (Top View) Samsung Electronics...
Page 8
2) Momently short-circuit the test point on Main 6) Turn the Power off. PCB with pincers to set the adjustment mode. (See Fig. 2-2 and 2-3) 3) Press the “5” button of remote control then adjust- ment is operated automatically. (See Fig. 2-1) Samsung Electronics...
Page 12
Exploded View and Parts List 3-1 Cabinet Assembly Samsung Electronics...
Page 13
Exploded View and Parts List Loc. No Parts No. Description ; Specification Remark Refer to table below ASSY-PANEL FRONT;HIPS94V2,SV-G180UM,BLK Refer to table below DOOR-CASSETTE;SV-G180UM,ABS94HBBLK,-,-,- AC61-62032A SPRING-MASK;X-9,-,SUS,-,4.4,-,SV-C130 AC64-00616B KNOB-JOG;01T,SILVER,ABS,-,-,-,-,-,- SV-G180UM/G180P ONLY AC64-00617B KNOB-SHUTTLE;01T,SILVER,ABS,-,-,-,-,-,- SV-G180UM/G180P ONLY AC61-30164D LOCKER-CODO ASSY L;-,LUCEL+SECC+SUS,-,-, AC61-30164C LOCKER-CODO ASSY R;-,LUCEL+SECC+SUS,-,BL Refer to table below CABINET-TOP;-,PCM(SECC),-,T0.5,-,MD552,-...
Page 18
Exploded View and Parts List MEMO Samsung Electronics...
Page 19
4. Electrical Parts List 4-1 SV-G180UM/G175UM/G170UM/G75UM/G70UM/G100UP/G70P/G50UP/G180P/G175P/G171P Only Loc.No Part No Description ; Specification Remark Loc.No Part No Description ; Specification Remark ASSY PCB-MAIN S.N.A. L1SS02 AC27-12001N COIL-CHOKE;10UH-15%,RA,K-30,Q80,150KHZ,- L1SS03 AC27-12001N COIL-CHOKE;10UH-15%,RA,K-30,Q80,150KHZ,- S.M.P.S. PARTS PT1SD1 AC26-00001D TRANS-SWITCHING;-,100V-240V,DEMCO,EE2821 FREE VOLTAGE ONLY BD1SF1 3301-000297 CORE-FERRITE BEAD;AA,3.6x1.2x5.7mm,1400,...
Important safety notices : Components identified with the mark have the special characteristics for safety. When replacing any of these components. Use only the same type. ♦ Block Identification of Main PCB Component Side Conductor Side Samsung Electronics...
Page 44
1-1-1 Top View Œ ´ ˇ ¨ ˆ Ø Fig. 1-1 Top parts Location-1 Œ GEAR FL CAM ´ MOTOR LOADING ASS’Y ˇ LEVER FL ARM ASS’Y ¨ HOLDER FL CASSETTE ASS’Y ˆ LEVER FL DOOR Ø SLIDER FL DRIVE Samsung Electronics...
Page 45
´ CYLINDER ASS’Y ˝ GEAR IDLE ˇ ACE HEAD ASS’Y Ô LEVER IDLE ¨ LEVER UNIT PINCH ASS’Y LEVER T BRAKE ASS’Y ˆ LEVER #9 GUIDE ASS’Y Ò DISK T REEL Ø LEVER TENSION ASS’Y ∏ BAND BRAKE ASS’Y Samsung Electronics...
Page 46
Œ GEAR JOINT 1 ´ GEAR JOINT 2 ˇ BRACKET GEAR ¨ MOTOR CAPSTAN ASS’Y ˆ LEVER T LOAD ASS’Y Ø GEAR LOADING DRIVE ∏ LEVER S LOAD ASS’Y ” HOLDER CLUTCH ASS’Y ’ BELT PULLEY ˝ SLIDER CAM Samsung Electronics...
Page 47
Lever FL Cassette-R ´ at disassembling and "B" reassembling. ´ LEVER FL DOOR ˇ HOOK "C" Fig. 1-4 Lever FL Door Removal RAIL [B] Œ HOLDER FL ´ LEVER FL CASSETTEE -R CASSETTEE ASS`Y "A" BOSS [A] Fig. 1-5 Holder FL Cassette Ass’y Removal Samsung Electronics...
Page 51
LEVER LOAD T LEVER LOAD S Lever Tension Drive Removal TIMING POINT 2 TIMING POINT 3 PIN A PIN C PIN D PIN B ˇ SLIDER CAM Fig. 1-14 Gear Loading Drive, Slider Cam, Lever Load S, T Ass’y Assembly Samsung Electronics...
Page 52
ˇ SPRING BRAKE Œ SPRING TENTION LEVER STOPPER Œ LEVER S BRAKE ASS`Y "A" HOOK(C) MARK[B] HOOK(B) ´ LEVER T BRAKE ASS`Y Fig. 1-16 Lever Tension Ass’y, Band Brake Ass’y Removal Fig. 1-17 Lever Brake S, T Ass’y Removal Samsung Electronics...
Page 53
´ DISK T REEL add oil in the boss of Lever Idle Œ. "A" Œ LEVER IDLE ´ GEAR IDLE "B" ´ GEAR IDLE HOOK "C" Fig. 1-19 Disk S, T Reel Removal Fig. 1-18 Gear Idle Ass’y Removal 1-10 Samsung Electronics...
Page 54
Fig. 1-21 Lever Up Down Ass’y Removal SPRING GEAR CENTER ASS'Y GUIDE LEVER UP DOWN ASS'Y RING <BAD> <GOOD> GEAR POST HOOK Fig. 1-20 Holder Clutch Ass’y Removal MAIN BASE Fig. 1-22 Lever Up Down Ass’y Removal Samsung Electronics 1-11...
Page 55
Œ GUIDE CASSETTE DOOR Œ LEVER UNIT PINCH ASS`Y HOOK [A] ´ PLATE JOINT ˇ SPRING PINCH DRIVE Fig. 1-23 Guide Cassette Door Removal Fig. 1-24 Lever Unit Pinch Ass’y, Plate Joint, Spring Pinch Drive Removal 1-12 Samsung Electronics...
Page 56
2) After reinstalling, check the bottom side of the Post #9 Guide to the top side of Main Base. "A" Œ SPRING #9 GUIDE ´ LEVER #9 GUIDE ASS`Y "B" Fig. 1-26 FE Head Removal Fig. 1-25 Lever #9 Guide Ass’y Removal Samsung Electronics 1-13...
Page 57
2) Remove the screw Œ. 3) Lift the ACE Head Ass’y ´. Œ SLIDER S ASS`Y Œ SCREW ´ SLIDER T ASS`Y ´ HEAD ACE ASS`Y Fig. 1-28 Slider S, T Ass’y Removal Fig. 1-27 ACE Head Removal 1-14 Samsung Electronics...
Page 58
1) Release the Hook Œ. 2) Lift the Lever Head Cleaner Ass’y ´. ´ LEVER HEAD CLEANER ASS'Y Œ HOOK SLEEVE-HEAD CLEANER ˇ CYLINDER ASS'Y Fig. 1-29 Plate Ground Deck, Cylinder Ass’y Removal Fig. 1-31 Level Head Cleaner Ass’y Removal Samsung Electronics 1-15...
Page 59
3) Rotate Gear Worm Œ clockwise using screw driver again up to the state of eject mode and then pick out the tape.(Refer to Fig.1-33) ˇ MOTOR CAPSTAN ASS'Y Fig. 1-32 Damper Capstan,Motor Capstan Ass’y Removal FRAME Fig. 1-33 1-16 Samsung Electronics...
Page 60
CAPSTAN MOTOR PULLEY BELT PULLEY ∆ HOLDER CLUTCH ASS’Y GEAR CENTER ASS’Y GEAR IDLE (2Point) LOADING MOTOR BAND BRAKE ASS’Y BRAKE T ASS’Y ◆ : Add Oil ∆ : Cleaning O : Check and replacement in necessary Samsung Electronics 1-17...
Page 61
Disassembly and Reassembly MEMO 1-18 Samsung Electronics...
Page 62
Fig. 2-1 Location of Tape Transport Adjustment FE HEAD CYLINDER ASS'Y PINCH ROLLER GUIDE ROLLER "S" GUIDE ROLLER "T" POST TENSION #8 GUIDE POST #9 GUIDE POST #3 GUIDE POST MAIN BASE ACE HEAD CAPSTAN SHAFT Fig. 2-2 Tape Travel Diagram Samsung Electronics...
Page 63
ADJUSTMENT Fig. 2-3 Location of ACE Head Adjustment Screw 1) See “2. Alignment and Adjustment” for ACE Head position (X-Point) adjustment. AUDIO HEAD VIDEO HEAD 0 ~ 0 .25 mm CONTROL HEAD Fig. 2-4 ACE Head Height Adjustment Samsung Electronics...
Page 64
) driver to obtain a flat video RF envelope as shown in Fig. 2-8. IDEAL ENVELOPE S HEIGHT TOO HIGH S HEIGHT TOO LOW T HEIGHT TOO HIGH T HEIGHT TOO LOW GUIDE ROLLER S GUIDE ROLLER T Fig. 2-8 Guide Roller S, T Height Adjustment Samsung Electronics...
Page 65
3) Brake is operated by slider cam at FF/REW mode. 4) Transportation of accurate driving force is done by gears. (Gear Center Ass’y) Note : If the spec. does not meet the followings speci- fications, replace the holder clutch ass’y and then recheck. Samsung Electronics...