Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for BSK Zephyr V2.0
Summary of Contents for BSK Zephyr V2.0
- Page 1 User Manual BSK Zephyr V2.0 Decentralized Heat Recovery Device...
-
Page 2: Part List
Part List Front cover part Inside cover part Wall fixture part Outer hood part Capsule part Filters Ceramic heat exchanger 2-way fan O-ring gaskets 10. Telescopic pipe (inside piece) 11. Telescopic pipe (outside piece) - Page 3 Wall Montage and Assembly For the installation of BSK Zephyr decentralized heat recovery device, a hole must be drilled on a wall facing the exterior with the dimensions indicated in the figure. In order for the condensation water to flow outwards, the hole must be drilled with an outward slope of about 2-3 degrees.
- Page 4 3. Align the capsule part such that the fan socket 4. Put the front cover part on to the inner cover is on the left. Then push it inside the pipe, part and push the hinges. Make sure that both making sure the fans socket is correctly seated.
-
Page 5: Electrical Connection
Wireless Pairing of Multiple Devices BSK Zephyr devices can work individually or as a group by connecting to each other wirelessly. By connecting devices in more than one room or in different rooms, you can also control other connected devices through a single master device. -
Page 6: Address List
Secondary Device - Parallel Mode; It works in parallel with the primary device by connecting to the primary device with the same address. (E.g., Primary device blows air out while secondary device does the same and blows air out) The #1 key is set to OFF and the #2 key set to ON. Address keys #3-4- 5-6 are set to be the same as the primary device to be connected. -
Page 7: On/Off Button
IR Remote On/Off Button: When this button is pressed while the device is in the off position, the front cover will open and the fan will start to operate. When this button is pressed while the device is on, the front cover will be closed and the fan will stop. Air Flow Mode Buttons •... -
Page 8: General Maintenance
Level I Level II Level III • Thanks to the humidity sensor on the device, it constantly controls the relative humidity level in the environment. If the humidity level in the environment is above the determined level, the device switches to shot mode for moisture evacuation. When the humidity level in the environment falls below the specified level, the device continues to operate normally. - Page 9 Filter Change and Capsule Disassembly 1. Remove the front cover piece by first tilting it about 45 degrees and then pulling it up from the inner cover piece. 2. Remove the capsule piece by holding it from its sides and pulling it off from the pipe.
- Page 10 3. You can remove the filter pieces by turning them counter-clock wise and pulling them off from the capsule piece. You do not need to disassemble the capsule pieces just to remove filters. 4. After removing both the front and the back filter, you can insert new filter cartridges, change the filters inside their cartridges or clean them with compressed air or warm water;...
- Page 11 6. Remove the 2 elastic gaskets holding the capsule together. Be careful that once the gaskets are off there will be nothing holding the 2 halves of the capsule together 7. Gently remove the ceramic heat exchanger core 8. Unplug the wire from its socket and then from inside the capsule.
- Page 12 Cleaning the Capsule 1. You can clean the capsule pieces by gently wiping them with a wet towel or sponge. Let them dry for a few hours before assembling them back. 2. You can clean the fan by gently wiping its blades and cover with a wet towel or sponge. Let it dry for a few hours before putting it back in.
- Page 13 Pairing your BSK Zephyr device with the Mobile App Download the iOS app from Apple Store Download the Android app from Google Play Store 1. Turn off your device using the IR remote control 2. Press and hold “Night Mode” button while the device is turned off.
- Page 14 4. Login to your BSK Zephyr app, then press “Add 5. Select your device from the available device Device” button. list. 6. A list of available networks will be shown. Select 7. Enter your Wi-Fi network password, and then the network you want to connect.
- Page 15 8. When the device successfully connects to your 9. You can now control your BSK Zephyr from network, press “Go to Panel” button. your mobile device.
Need help?
Do you have a question about the Zephyr V2.0 and is the answer not in the manual?
Questions and answers